Home › Suspension › ALIGNMENT / HANDLING DIAGNOSIS › FRONT WHEEL ALIGNMENT › from 2018.08
RM2170E _53 Suspension _057016 ALIGNMENT / HANDLING DIAGNOSIS _0278004 FRONT WHEEL ALIGNMENT N

ALIGNMENT / HANDLING DIAGNOSIS  FRONT WHEEL ALIGNMENT  ADJUSTMENT  


CAUTION / NOTICE / HINT

NOTICE:

If the wheel alignment has been adjusted, or if suspension or underbody components have been removed/installed or replaced, be sure to perform the following initialization procedure in order for the system to function normally:

Perform zero point calibration of the yaw rate and acceleration sensor.



PROCEDURE

Hide 1. PRECAUTION

Standard values indicated by *1 and *2 in the specification tables are for the vehicles with a purple or blue identification mark on the bottom of the rear coil spring.

C253259C01
2.094,1.698 2.875,1.698 true 2.917,1.604 3.083,1.781 0.167,0.177 10 false *a
*a Colored identification mark on the bottom of the rear coil spring


Hide 3.MEASURE VEHICLE HEIGHT

NOTICE:
·

Before inspecting the wheel alignment, adjust the vehicle height to the specified value.

·

Be sure to perform measurement on a level surface.

·

If it is necessary to go under the vehicle for measurement, confirm that the parking brake is applied and the vehicle is secured with chocks.

·

Inspect while the vehicle is unloaded.

·

The standard value shown here is a value that is used for adjusting the wheel alignment and does not indicate the height of an actual vehicle.



a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.
C249970N03
0.19,3.754 0.320,3.896 0.130,0.142 10 C 1.459,3.825 1.583,3.967 0.124,0.142 10 A 1.825,3.788 1.943,3.930 0.118,0.142 10 B 3.219,3.757 3.341,3.899 0.122,0.142 10 D

Measure the vehicle height.

Measurement points:

A: Ground clearance of front lower No. 1 suspension arm bushing set bolt center


B: Ground clearance of rear axle beam bushing set bolt center


C: Ground clearance of front wheel center


D: Ground clearance of rear wheel center


Vehicle Height (Unloaded Vehicle):
Tire Size Front C - A Rear D - B

*1: Vehicles with purple identification mark on the bottom of the rear coil spring

*2: Vehicles with blue identification mark on the bottom of the rear coil spring

*3: for Taiwan

*4: for Korea

*5: for Australia

*6: for New Zealand

175/65R15 92 mm (3.62 in.)*1, *3
76 mm (2.99 in.)*2, *3
98 mm (3.86 in.)*4
29 mm (1.14 in.)*1, *3
12 mm (0.472 in.)*2, *3
34 mm (1.34 in.)*4
185/60R15 93 mm (3.66 in.)
79 mm (3.11 in.)*1
69 mm (2.72 in.)*2
77 mm (3.03 in.)*1, *5
92 mm (3.62 in.)*6
32 mm (1.26 in.)
14 mm (0.551 in.)*1
4 mm (0.157 in.)*2
12 mm (0.472 in.)*1, *5
28 mm (1.10 in.)*6



Hide 4.INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION

NOTICE:

Inspect while the vehicle is unloaded.


a.
C132440C25
2.396,1.104 2.51,0.823 2.51,0.823 2.74,0.823 false 0.604,0.708 1.031,0.708 1.031,0.708 1.031,1.458 false 2.76,0.729 2.99,0.906 0.229,0.177 10 false *b 0.448,0.604 0.688,0.781 0.24,0.177 10 false *a
*a Turning Radius Gauge
*b Camber-caster-kingpin Gauge


Install a camber-caster-kingpin gauge and place the front wheels on the center of a turning radius gauge.


b.

Inspect the camber, caster and steering axis inclination.

Camber (Unloaded Vehicle):
Tire Size Camber Inclination Right-left Difference

*1: Vehicles with purple identification mark on the bottom of the rear coil spring

*2: Vehicles with blue identification mark on the bottom of the rear coil spring

*3: for Taiwan

*4: for Korea

*5: for Australia

*6: for New Zealand

175/65R15 -0°13' +/- 0°45' (-0.22° +/- 0.75°)*1, *3
0°00' +/- 0°45' (0.00° +/- 0.75°)*2, *3
-0°16' +/- 0°45' (-0.27° +/- 0.75°)*4
0°30' (0.50°) or less
185/60R15 -0°13' +/- 0°45' (-0.22° +/- 0.75°)
-0°04' +/- 0°45' (-0.07° +/- 0.75°)*1
0°05' +/- 0°45' (0.08° +/- 0.75°)*2
-0°02' +/- 0°45' (-0.03° +/- 0.75°)*1, *5
-0°12' +/- 0°45' (-0.20° +/- 0.75°)*6


Caster (Unloaded Vehicle):
Tire Size Caster Inclination Right-left Difference

*1: Vehicles with purple identification mark on the bottom of the rear coil spring

*2: Vehicles with blue identification mark on the bottom of the rear coil spring

*3: for Taiwan

*4: for Korea

*5: for Australia

*6: for New Zealand

175/65R15 4°54' +/- 0°45' (4.90° +/- 0.75°)*1, *3
4°38' +/- 0°45' (4.63° +/- 0.75°)*2, *3
4°57' +/- 0°45' (4.95° +/- 0.75°)*4
0°30' (0.50°) or less
185/60R15 4°59' +/- 0°45' (4.98° +/- 0.75°)
4°41' +/- 0°45' (4.68° +/- 0.75°)*1
4°32' +/- 0°45' (4.53° +/- 0.75°)*2
4°38' +/- 0°45' (4.63° +/- 0.75°)*1, *5
4°53' +/- 0°45' (4.88° +/- 0.75°)*6


Steering Axis (Unloaded Vehicle):
Tire Size Steering Axis Inclination Reference

*1: Vehicles with purple identification mark on the bottom of the rear coil spring

*2: Vehicles with blue identification mark on the bottom of the rear coil spring

*3: for Taiwan

*4: for Korea

*5: for Australia

*6: for New Zealand

175/65R15 11°23' (11.38°)*1, *3
11°01' (11.02°)*2, *3
11°31' (11.52°)*4
185/60R15 11°25' (11.42°)
11°04' (11.07°)*1
10°49' (10.82°)*2
11°02' (11.03°)*1, *5
11°23' (11.38°)*6



Hide 5.ADJUST CAMBER

NOTICE:

Inspect toe-in after the camber has been adjusted.


a.

Remove the front wheel.


b.
C249872

Remove the 2 nuts on the lower side of the front shock absorber assembly.

NOTICE:

Keep the bolts inserted.



c.

Remove the top and bottom bolts one at a time and confirm that the steering knuckle can move freely in the front shock absorber assembly.

HINT:
·

Reinstall each bolt after removing it and confirming steering knuckle movement.

·

If the steering knuckle does not move freely in the front shock absorber assembly, clean the installation surfaces of the front shock absorber assembly and the steering knuckle.




d.

Temporarily install the 2 nuts. (Step A)


e.
C131799

Fully push or pull the front axle hub in the direction of the required adjustment. (Step B)


f.
C249872

Tighten the nuts.

Torque:
164 N*m (1672 kgf*cm, 121 ft.*lbf)

NOTICE:

Keep the bolts from rotating when tightening the nuts.



g.

Install the front wheel.

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)


h.

Bounce the vehicle up and down at the corners to stabilize the suspension.


i.

Check the camber.

Camber (Unloaded Vehicle):
Tire Size Camber Inclination Right-left Difference

*1: Vehicles with purple identification mark on the bottom of the rear coil spring

*2: Vehicles with blue identification mark on the bottom of the rear coil spring

*3: for Taiwan

*4: for Korea

*5: for Australia

*6: for New Zealand

175/65R15 -0°13' +/- 0°45' (-0.22° +/- 0.75°)*1, *3
0°00' +/- 0°45' (0.00° +/- 0.75°)*2, *3
-0°16' +/- 0°45' (-0.27° +/- 0.75°)*4
0°30' (0.50°) or less
185/60R15 -0°13' +/- 0°45' (-0.22° +/- 0.75°)
-0°04' +/- 0°45' (-0.07° +/- 0.75°)*1
0°05' +/- 0°45' (0.08° +/- 0.75°)*2
-0°02' +/- 0°45' (-0.03° +/- 0.75°)*1, *5
-0°12' +/- 0°45' (-0.20° +/- 0.75°)*6


i.
C253266N02
0.331,1.081 0.426,1.222 0.095,0.142 10 1 0.329,1.29 0.425,1.431 0.095,0.142 10 2 0.445,1.158 0.657,1.158 false 0.436,1.379 0.648,1.379 false

If the measured value is not within the specification, calculate the required adjustment amount using the formula below.

Camber adjustment amount = center of the specified range - measured value

Check the combination of the installed bolts. Select appropriate bolts from the tables below to adjust the camber to the specified values.

HINT:

Try to adjust the camber to the center of the specified values.


To move the axle hub toward (+) in step B To move the axle hub toward (-) in step B
Refer to table (1) (To move the axle hub toward the positive side) Refer to table (2) (To move the axle hub toward the negative side)

The vehicle body and suspension may be damaged if the camber cannot be correctly adjusted according to the table above.

NOTICE:

Replace the nut with a new one when replacing the bolt.



ii.

Table (1) (To move the axle hub toward the positive side)

C212217C15
2.052,0.531 2.188,0.74 0.135,0.208 10 1 2.052,1.146 2.188,1.354 0.135,0.208 10 2 2.521,0.792 2.75,0.99 0.229,0.198 10 *c 3.219,1.406 3.448,1.594 0.229,0.188 10 *d 5.979,0.792 6.198,0.99 0.219,0.198 10 *e 5.271,0.792 5.521,0.99 0.25,0.198 10 *d 4.604,1.406 4.781,1.583 0.177,0.177 10 *f 3.917,1.406 4.125,1.615 0.208,0.208 10 *e 4.396,6.375 4.583,6.552 0.188,0.177 10 *f 5.969,1.396 6.177,1.552 0.208,0.156 10 *f 5.271,1.406 5.469,1.583 0.198,0.177 10 *f 6.656,1.396 6.833,1.552 0.177,0.156 10 *f 6.646,0.792 6.854,0.969 0.208,0.177 10 *f 2.542,2.99 2.719,3.219 0.177,0.229 10 A 2.542,4.188 2.771,4.406 0.229,0.219 10 F 2.542,3.469 2.771,3.688 0.229,0.219 10 C 2.542,3.938 2.74,4.156 0.198,0.219 10 E 2.542,3.24 2.729,3.448 0.188,0.208 10 B 2.542,3.708 2.729,3.927 0.188,0.219 10 D 3.927,3.01 4.177,3.24 0.25,0.229 10 C 5.271,3 5.51,3.229 0.24,0.229 10 E 3.229,3.01 3.406,3.219 0.177,0.208 10 B 4.604,3 4.792,3.24 0.188,0.24 10 D 3.229,2.76 3.448,2.99 0.219,0.229 10 G 3.229,3.24 3.406,3.448 0.177,0.208 10 C 3.229,3.708 3.448,3.938 0.219,0.229 10 E 3.229,3.469 3.427,3.698 0.198,0.229 10 D 3.229,3.938 3.427,4.167 0.198,0.229 10 F 3.927,2.51 4.115,2.74 0.188,0.229 10 G 3.927,2.76 4.135,2.969 0.208,0.208 10 A 3.927,3.708 4.115,3.938 0.188,0.229 10 F 3.917,3.469 4.083,3.688 0.167,0.219 10 E 3.927,3.24 4.135,3.458 0.208,0.219 10 D 4.604,2.281 4.802,2.531 0.198,0.25 10 G 6.656,1.563 6.833,1.823 0.177,0.26 10 G 5.979,1.813 6.26,2.063 0.281,0.25 10 G 5.271,2.031 5.458,2.281 0.188,0.25 10 G 6.656,1.813 6.813,2.042 0.156,0.229 10 A 6.656,2.281 6.844,2.531 0.188,0.25 10 C 6.656,2.76 6.885,3.01 0.229,0.25 10 E 6.656,2.031 6.833,2.26 0.177,0.229 10 B 6.656,2.51 6.875,2.781 0.219,0.271 10 D 5.979,2.031 6.177,2.292 0.198,0.26 10 A 5.979,2.51 6.188,2.75 0.208,0.24 10 C 5.979,2.281 6.26,2.531 0.281,0.25 10 B 5.979,2.76 6.167,2.99 0.188,0.229 10 D 5.979,3 6.115,3.208 0.135,0.208 10 F 5.271,3.24 5.49,3.448 0.219,0.208 10 F 5.271,2.281 5.406,2.51 0.135,0.229 10 A 5.271,2.76 5.448,2.969 0.177,0.208 10 C 5.271,2.51 5.438,2.74 0.167,0.229 10 B 4.604,2.51 4.781,2.76 0.177,0.25 10 A 4.604,2.76 4.781,2.969 0.177,0.208 10 B 4.604,3.24 4.813,3.458 0.208,0.219 10 E 4.604,3.469 4.813,3.698 0.208,0.229 10 F 1.625,5.073 1.76,5.281 0.135,0.208 10 A 5.094,5.073 5.229,5.281 0.135,0.208 10 F 3.052,5.073 3.188,5.281 0.135,0.208 10 C 4.406,5.073 4.542,5.281 0.135,0.208 10 E 2.344,5.073 2.479,5.281 0.135,0.208 10 B 3.729,5.073 3.865,5.281 0.135,0.208 10 D 5.802,5.073 5.938,5.281 0.135,0.208 10 G 1.073,5.5 1.208,5.708 0.135,0.208 10 1 1.104,6.135 1.24,6.344 0.135,0.208 10 2 3.042,6.375 3.229,6.531 0.188,0.156 10 *f 3.719,6.375 3.958,6.542 0.24,0.167 10 *f 5.083,6.375 5.292,6.573 0.208,0.198 10 *f 5.094,5.75 5.292,5.917 0.198,0.167 10 *f 4.385,5.75 4.604,5.917 0.219,0.167 10 *e 2.333,6.375 2.542,6.542 0.208,0.167 10 *e 1.625,6.375 1.854,6.552 0.229,0.177 10 *d 3.719,5.75 3.927,5.938 0.208,0.188 10 *d 3.01,5.75 3.208,5.938 0.198,0.188 10 *c 1.625,5.75 1.844,5.948 0.219,0.198 10 *c 2.333,5.75 2.521,5.906 0.188,0.156 10 *c 5.802,6.365 6.021,6.563 0.219,0.198 10 *c 5.76,5.76 5.969,5.948 0.208,0.188 10 *c 0.177,1.563 2.198,1.75 2.021,0.188 10 -1°30' to -1°15' (-1.50° to -1.25°) 0.406,2.76 1.969,2.948 1.563,0.188 10 -0°15' to 0° (-0.25° to 0°) 0.208,2.51 2.156,2.729 1.948,0.219 10 -0°30' to -0°15' (-0.5° to -0.25°) 0.208,2.281 2.156,2.479 1.948,0.198 10 -0°45' to -0°30' (-0.75° to -0.5°) 0.271,2.031 2.104,2.208 1.833,0.177 10 -1°00' to -0°45' (-1° to -0.75°) 0.26,1.813 2.094,2.021 1.833,0.208 10 -1°15' to -1°00' (-1.25° to -1°) 0.354,3.938 2.01,4.115 1.656,0.177 10 1°00' to 1°15' (1° to 1.25°) 0.354,3.708 2,3.906 1.646,0.198 10 0°45' to 1°00' (0.75° to 1°) 0.302,3.469 2.073,3.646 1.771,0.177 10 0°30' to 0°45' (0.5° to 0.75°) 0.302,3.24 2.073,3.417 1.771,0.177 10 0°15' to 0°30' (0.25° to 0.5°) 0.448,3 1.917,3.198 1.469,0.198 10 0° to 0°15' (0° to 0.25°) 0.302,4.188 2.073,4.365 1.771,0.177 10 1°15' to 1°30' (1.25° to 1.5°) 2.542,1.406 2.76,1.604 0.219,0.198 10 *c 3.219,0.792 3.448,0.969 0.229,0.177 10 *c 3.917,0.792 4.135,1.01 0.219,0.219 10 *c 4.604,0.792 4.823,1.01 0.219,0.219 10 *c 5.979,3 6.24,3.24 0.26,0.24 10 F 1.156,0.625 1.333,0.792 0.177,0.167 10 *a 0.625,1.115 0.802,1.281 0.177,0.167 10 *b 0.875,4.792 1.198,5.021 0.323,0.229 12 *B 0.063,0.135 0.333,0.333 0.271,0.198 12 *A
*A Table (1) (To move the axle hub toward the positive side) *B Selected Bolt Combination
*a Installed Bolt *b Adjusting Value
*c 90109-15001 *d 90109-15002
*e 90109-15003 *f 90109-15004



iii.

Table (2) (To move the axle hub toward the negative side)

C212218C15
2.052,0.531 2.188,0.74 0.135,0.208 10 1 2.052,1.146 2.188,1.354 0.135,0.208 10 2 1.635,5.052 1.771,5.26 0.135,0.208 10 A 5.094,5.052 5.229,5.26 0.135,0.208 10 F 3.052,5.052 3.188,5.26 0.135,0.208 10 C 4.406,5.052 4.542,5.26 0.135,0.208 10 E 2.344,5.052 2.479,5.26 0.135,0.208 10 B 3.729,5.052 3.865,5.26 0.135,0.208 10 D 5.802,5.052 5.938,5.26 0.135,0.208 10 G 1.073,5.5 1.208,5.708 0.135,0.208 10 1 1.104,6.135 1.24,6.344 0.135,0.208 10 2 0.177,1.563 2.198,1.75 2.021,0.188 10 -1°30' to -1°15' (-1.50° to -1.25°) 0.406,2.76 1.969,2.948 1.563,0.188 10 -0°15' to 0° (-0.25° to 0°) 0.208,2.521 2.156,2.74 1.948,0.219 10 -0°30' to -0°15' (-0.5° to -0.25°) 0.208,2.281 2.156,2.479 1.948,0.198 10 -0°45' to -0°30' (-0.75° to -0.5°) 0.271,2.031 2.104,2.208 1.833,0.177 10 -1°00' to -0°45' (-1° to -0.75°) 0.26,1.813 2.094,2.021 1.833,0.208 10 -1°15' to -1°00' (-1.25° to -1°) 0.354,3.938 2.01,4.115 1.656,0.177 10 1°00' to 1°15' (1° to 1.25°) 0.354,3.708 2,3.906 1.646,0.198 10 0°45' to 1°00' (0.75° to 1°) 0.302,3.469 2.073,3.646 1.771,0.177 10 0°30' to 0°45' (0.5° to 0.75°) 0.302,3.24 2.073,3.417 1.771,0.177 10 0°15' to 0°30' (0.25° to 0.5°) 0.448,3 1.917,3.198 1.469,0.198 10 0° to 0°15' (0° to 0.25°) 0.302,4.188 2.073,4.365 1.771,0.177 10 1°15' to 1°30' (1.25° to 1.5°) 1.156,0.625 1.333,0.792 0.177,0.167 10 *a 0.625,1.115 0.802,1.281 0.177,0.167 10 *b 0.875,4.792 1.167,5.021 0.292,0.229 12 *B 0.063,0.135 0.417,0.354 0.354,0.219 12 *A 5.292,2.76 5.427,2.969 0.135,0.208 10 E 5.292,3.708 5.427,3.917 0.135,0.208 10 G 5.292,2.521 5.427,2.729 0.135,0.208 10 F 5.292,3.469 5.427,3.677 0.135,0.208 10 A 5.292,3 5.427,3.208 0.135,0.208 10 C 5.292,3.24 5.427,3.448 0.135,0.208 10 B 2.542,2.76 2.677,2.969 0.135,0.208 10 A 2.542,1.563 2.677,1.771 0.135,0.208 10 F 2.542,2.281 2.677,2.49 0.135,0.208 10 C 2.542,1.813 2.677,2.021 0.135,0.208 10 E 2.542,2.521 2.677,2.729 0.135,0.208 10 B 2.542,2.031 2.677,2.24 0.135,0.208 10 D 3.229,2.76 3.365,2.969 0.135,0.208 10 B 3.229,3 3.365,3.208 0.135,0.208 10 G 3.229,2.521 3.365,2.729 0.135,0.208 10 C 3.229,2.031 3.365,2.24 0.135,0.208 10 E 3.229,2.281 3.365,2.49 0.135,0.208 10 D 3.229,1.813 3.375,2.021 0.146,0.208 10 F 3.927,2.76 4.063,2.969 0.135,0.208 10 C 3.927,3.24 4.063,3.448 0.135,0.208 10 G 3.927,3 4.063,3.208 0.135,0.208 10 A 3.927,2.031 4.063,2.24 0.135,0.208 10 F 3.927,2.281 4.063,2.49 0.135,0.208 10 E 3.927,2.521 4.063,2.729 0.135,0.208 10 D 4.604,2.76 4.74,2.969 0.135,0.208 10 D 4.604,3.469 4.74,3.677 0.135,0.208 10 G 4.604,3.24 4.74,3.448 0.135,0.208 10 A 4.604,3 4.74,3.208 0.135,0.208 10 B 4.604,2.521 4.74,2.729 0.135,0.208 10 E 4.604,2.281 4.74,2.49 0.135,0.208 10 F 5.99,3.938 6.125,4.146 0.135,0.208 10 G 5.99,3.708 6.125,3.917 0.135,0.208 10 A 5.99,3.24 6.125,3.448 0.135,0.208 10 C 5.99,3.469 6.125,3.677 0.135,0.208 10 B 5.99,3 6.125,3.208 0.135,0.208 10 D 5.99,2.76 6.125,2.969 0.135,0.208 10 F 6.688,4.188 6.823,4.396 0.135,0.208 10 G 6.688,3.938 6.823,4.146 0.135,0.208 10 A 6.688,3.469 6.823,3.677 0.135,0.208 10 C 6.688,3 6.823,3.208 0.135,0.208 10 E 6.688,3.708 6.823,3.917 0.135,0.208 10 B 6.688,3.24 6.823,3.448 0.135,0.208 10 D 2.51,0.792 2.729,0.969 0.219,0.177 10 *c 3.219,1.396 3.406,1.573 0.188,0.177 10 *d 5.969,0.781 6.115,0.938 0.146,0.156 10 *e 5.271,0.792 5.469,0.979 0.198,0.188 10 *d 4.604,1.396 4.781,1.573 0.177,0.177 10 *f 3.906,1.396 4.083,1.573 0.177,0.177 10 *e 5.979,1.396 6.188,1.552 0.208,0.156 10 *f 5.281,1.396 5.479,1.573 0.198,0.177 10 *f 6.656,1.396 6.833,1.552 0.177,0.156 10 *f 6.656,0.792 6.823,0.958 0.167,0.167 10 *f 2.51,1.396 2.688,1.573 0.177,0.177 10 *c 3.219,0.792 3.396,0.948 0.177,0.156 10 *c 3.927,0.792 4.115,0.979 0.188,0.188 10 *c 4.604,0.792 4.781,0.958 0.177,0.167 10 *c 4.385,6.375 4.531,6.531 0.146,0.156 10 *f 3.01,6.375 3.198,6.531 0.188,0.156 10 *f 3.708,6.375 3.948,6.542 0.24,0.167 10 *f 5.094,6.375 5.302,6.573 0.208,0.198 10 *f 5.083,5.75 5.271,5.906 0.188,0.156 10 *f 4.375,5.75 4.573,5.906 0.198,0.156 10 *e 2.313,6.375 2.521,6.542 0.208,0.167 10 *e 1.625,6.375 1.771,6.531 0.146,0.156 10 *d 3.688,5.75 3.875,5.938 0.188,0.188 10 *d 3.01,5.75 3.208,5.938 0.198,0.188 10 *c 1.625,5.74 1.802,5.927 0.177,0.188 10 *c 2.323,5.75 2.5,5.906 0.177,0.156 10 *c 5.781,6.375 5.969,6.542 0.188,0.167 10 *c 5.771,5.75 5.979,5.938 0.208,0.188 10 *c
*A Table (2) (To move the axle hub toward the negative side) *B Selected Bolt Combination
*a Installed Bolt *b Adjusting Value
*c 90109-15001 *d 90109-15002
*e 90109-15003 *f 90109-15004




j.

If the camber was out of adjustment in the previous step, perform the adjust camber steps mentioned above. In step (A), replace the existing bolts with the selected bolts.

HINT:

Replace one bolt at a time when replacing both bolts.



Hide 6.INSPECT TOE-IN

NOTICE:

Inspect while the vehicle is unloaded.


a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.

Release the parking brake and move the shift lever to N.


c.

Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step C)


d.
C188968C24
0.833,0.583 0.833,1.115 false 1.365,0.583 1.365,0.99 1.365,0.99 0.833,0.99 false 2.521,1.333 2.521,1.667 false 0.74,1.135 0.917,1.302 0.177,0.167 10 *a 2.427,1.698 2.604,1.854 0.177,0.156 10 *b
*a Tread Center Mark
*b Dimension B
V100135

Front of the Vehicle


Put tread center marks on the rearmost points of the front wheels and measure the distance between the marks (dimension B).


e.

Slowly push the vehicle straight ahead to cause the front wheels to rotate 180°. Use the front tire valve as a reference point.

HINT:

Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from Step C again.



f.
C188969C24
0.646,1.271 0.646,1.635 false 1.917,0.542 2.052,0.698 0.135,0.156 10 C 3.073,0.552 3.208,0.708 0.135,0.156 10 D 2.5,0.719 2.635,0.875 0.135,0.156 10 A 2.51,1.542 2.646,1.698 0.135,0.156 10 B 0.563,1.656 0.74,1.813 0.177,0.156 10 *a
*a Dimension A
V100135

Front of the Vehicle


Measure the distance between the tread center marks on the front of the wheels (dimension A).

Toe-in (Unloaded Vehicle):
Tire Size Specified Condition
175/65R15 C + D: 0°06' +/- 0°12' (0.10° +/- 0.21°)
B - A: 1.0 +/- 2.0 mm (0.0394 +/- 0.0787 in.)
185/60R15 C + D: 0°06' +/- 0°12' (0.09° +/- 0.19°)
B - A: 1.0 +/- 2.0 mm (0.0394 +/- 0.0787 in.)


HINT:

Measure "B - A" only when "C + D" cannot be measured.


If the toe-in is not within the specified range, adjust it at the rack ends.


Hide 7.ADJUST TOE-IN

a.
C249963C03
2.5,1.188 2.719,1.385 0.219,0.198 10 true *a
*a Thread Length


Make sure that the thread length of the right and left rack ends are approximately the same.

Standard Difference:

1.5 mm (0.0591 in.) or less



b.

Separate the boot clips.


c.
C249964

Loosen the tie rod end lock nuts.


d.

Adjust the rack ends if the difference in thread length between the right and left rack ends is not within the specified range.

i.

Extend the shorter rack end if the measured toe-in deviates toward the outer-side.


ii.

Shorten the longer rack end if the measured toe-in deviates toward the inner-side.



e.
C317577C20
1.625,0.51 1.781,0.708 0.156,0.198 10 false A 1.667,1.365 1.823,1.563 0.156,0.198 10 false B 1.031,0.323 1.188,0.521 0.156,0.198 10 false C 2.208,0.344 2.365,0.542 0.156,0.198 10 false D
V100135

Front of the Vehicle


Turn the right and left rack ends by an equal amount to adjust the toe-in.

Toe-in (Unloaded Vehicle):
Tire Size Specified Condition
175/65R15 C + D: 0°06' +/- 0°12' (0.10° +/- 0.21°)
B - A: 1.0 +/- 2.0 mm (0.0394 +/- 0.0787 in.)
185/60R15 C + D: 0°06' +/- 0°12' (0.09° +/- 0.19°)
B - A: 1.0 +/- 2.0 mm (0.0394 +/- 0.0787 in.)


HINT:

Perform adjustments so that the value is as close as possible to the median of the specified range.



f.

Make sure that the thread lengths of the right and left rack ends are the same.


g.

Tighten the tie rod end lock nuts.

Torque:
75 N*m (760 kgf*cm, 55 ft.*lbf)


h.

Place the boots on the seats and install the clips.

HINT:

Make sure that the boots are not twisted.



Hide 8.INSPECT WHEEL ANGLE

a.
C132439C20
0.863,0.204 1.036,0.381 0.173,0.177 10 *b 0.538,0.204 0.713,0.381 0.176,0.177 10 *a 2.397,0.204 2.57,0.381 0.173,0.177 10 *b 2.725,0.204 2.901,0.381 0.176,0.177 10 *a
*a Inside
*b Outside
V100135

Front of the Vehicle


Put tread center marks on the rearmost points of a turning radius gauge.


b.

Turn the steering wheel fully to the left and right and measure the turning angle.

NOTICE:

Inspect while the vehicle is unloaded.


Wheel Turning Angle (Unloaded Vehicle):
Tire Size Inside Wheel Outside Wheel Reference

*1: Vehicles with purple identification mark on the bottom of the rear coil spring

*2: Vehicles with blue identification mark on the bottom of the rear coil spring

*3: for Taiwan

*4: for Korea

*5: for Australia

*6: for New Zealand

175/65R15 40°50' +/- 2° (40.83° +/- 2°)*1, *3
41°12' +/- 2° (41.20° +/- 2°)*2, *3
40°42' +/- 2° (40.70° +/- 2°)*4
35°11' (35.18°)*1, *3
35°32' (35.53°)*2, *3
35°02' (35.03°)*4
185/60R15 40°50' +/- 2° (40.83° +/- 2°)
41°09' +/- 2° (41.15° +/- 2°)*1
41°21' +/- 2° (41.35° +/- 2°)*2
41°11' +/- 2° (41.18° +/- 2°)*1, *5
40°52' +/- 2° (40.87° +/- 2°)*6
35°09' (35.15°)
35°30' (35.50°)*1
35°44' (35.73°)*2
35°32' (35.53°)*1, *5
35°11' (35.18°)*6


If the right and left inside wheel angles differ from the specified value, check and adjust the right and left rack end lengths.



Hide 9.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 10.PERFORM YAW RATE AND ACCELERATION SENSOR CALIBRATION