Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2018.08
RM2170E _58 Vehicle Interior _057039 SUPPLEMENTAL RESTRAINT SYSTEMS _0278099 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

DTC output mode is set by connecting terminals TC and CG of the DLC3.

DTCs are displayed by blinking of the SRS warning light.

HINT:
·

When multiple warning lights in the combination meter blink continuously, a ground short in the wiring or an ECU connected to terminal TC of the DLC3 is suspected.

·

A DTC output mode signal is transmitted through the CAN communication system to each ECU including the airbag sensor assembly. Thus when multiple systems do not enter DTC output mode, there may be a hybrid vehicle control ECU malfunction.



WIRING DIAGRAM

C265835E51
0.177,3.917 2.271,4.156 2.094,0.24 10 false *1: for RHD 0.292,3.354 2.427,3.625 2.135,0.271 10 false G81 1.375,0.896 1.667,1.333 0.292,0.438 10 false 24 1.375,0.208 1.656,0.49 0.281,0.281 10 false 25 1.385,2.083 1.927,2.49 0.542,0.406 10 false 28 0.948,1.052 1.469,1.521 0.521,0.469 10 false CA1L 0.927,0.375 1.469,0.802 0.542,0.427 10 false CA1H 5.938,2.188 6.271,2.458 0.333,0.271 10 false TC 1.115,2.177 1.521,2.458 0.406,0.281 10 false TC 5.698,2.083 6.031,2.396 0.333,0.313 10 false 13 5.76,2.708 6.063,2.958 0.302,0.25 10 false 4 5.927,2.802 6.271,3.094 0.344,0.292 10 false CG 5.906,3.344 6.885,3.646 0.979,0.302 10 false G4*1, G93*2 5.917,3.521 6.5,3.938 0.583,0.417 10 false DLC3 5.948,1.063 6.417,1.323 0.469,0.26 10 false CANL 5.604,1.5 6.833,1.802 1.229,0.302 10 false G18 5.698,0.906 5.99,1.177 0.292,0.271 10 false 22 5.688,0.198 6.021,0.448 0.333,0.25 10 false 13 5.948,0.365 6.469,0.781 0.521,0.417 10 false CANH 5.604,1.646 7.156,2.042 1.552,0.396 10 false Airbag Sensor Assembly 0.865,4.521 2.688,4.792 1.823,0.271 10 false : CAN Communication Line 0.302,3.521 2.396,3.76 2.094,0.24 10 false Hybrid Vehicle Control ECU 0.177,4.198 2.271,4.438 2.094,0.24 10 false *2: for LHD

PROCEDURE

1.CHECK WIRE HARNESS (TC OF DLC3 - TC OF HYBRID VEHICLE CONTROL ECU)
a.
C286199C18
0.135,0.854 0.479,1.094 0.344,0.24 0.26,3.417 0.667,3.677 0.406,0.26 0.135,1.156 0.479,1.396 0.344,0.24 2.073,1.906 2.073,1.49 true 0.729,4.323 1.865,3.99 true 0.198,0.156 0.542,0.448 0.344,0.292 10 false *1 0.281,2.417 0.646,2.781 0.365,0.365 10 false *a 0.229,0.896 0.573,1.188 0.344,0.292 10 false G4 0.333,3.469 0.677,3.76 0.344,0.292 10 false G81 2,1.927 2.344,2.219 0.344,0.292 10 false TC 0.542,4.25 0.885,4.542 0.344,0.292 10 false TC 0.521,0.896 0.865,1.188 0.344,0.292 10 false *A 0.188,1.198 0.531,1.49 0.344,0.292 10 false G93 0.531,1.198 0.875,1.49 0.344,0.292 10 false *B
*A for RHD
*B for LHD
*1 DLC3
*2 Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Turn the power switch off.


b.

Disconnect the connector from the hybrid vehicle control ECU.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD:
Tester Connection Condition Specified Condition
G4-13 (TC) - G81-28 (TC) Always Below 1 Ω

for LHD:
Tester Connection Condition Specified Condition
G93-13 (TC) - G81-28 (TC) Always Below 1 Ω




OK

2.CHECK WIRE HARNESS (CG OF DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE WIRE HARNESS

2.CHECK WIRE HARNESS (CG OF DLC3 - BODY GROUND)
a.
C204945C82
0.104,0.927 0.458,1.156 0.354,0.229 0.104,1.198 0.458,1.427 0.354,0.229 1.615,0.802 1.615,0.302 1.615,0.302 1.813,0.302 true 0.156,0.135 0.469,0.396 0.313,0.26 10 false *1 0.198,0.958 0.51,1.26 0.313,0.302 10 false G4 1.854,0.219 2.25,0.469 0.396,0.25 10 false CG 0.5,0.958 0.813,1.26 0.313,0.302 10 false *A 0.167,1.24 0.563,1.542 0.396,0.302 10 false G93 0.51,1.24 0.906,1.542 0.396,0.302 10 false *B
*A for RHD
*B for LHD
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD:
Tester Connection Condition Specified Condition
G4-4 (CG) - Body ground Always Below 1 Ω

for LHD:
Tester Connection Condition Specified Condition
G93-4 (CG) - Body ground Always Below 1 Ω




OK

3.CHECK WIRE HARNESS (TC OF DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE WIRE HARNESS

3.CHECK WIRE HARNESS (TC OF DLC3 - BODY GROUND)
a.
C204945C83
0.094,0.854 0.448,1.094 0.354,0.24 0.094,1.146 0.448,1.385 0.354,0.24 1.958,1.854 1.792,1.854 1.792,1.854 1.792,1.354 true 0.156,0.135 0.469,0.396 0.313,0.26 10 false *1 0.188,0.896 0.5,1.198 0.313,0.302 10 false G4 2,1.781 2.396,2.031 0.396,0.25 10 false TC 0.5,0.896 0.813,1.198 0.313,0.302 10 false *A 0.156,1.188 0.583,1.531 0.427,0.344 10 false G93 0.51,1.188 0.938,1.531 0.427,0.344 10 false *B
*A for RHD
*B for LHD
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD:
Tester Connection Condition Specified Condition
G4-13 (TC) - Body ground Always 1 MΩ or higher

for LHD:
Tester Connection Condition Specified Condition
G93-13 (TC) - Body ground Always 1 MΩ or higher




OK

NG

REPAIR OR REPLACE WIRE HARNESS OR REPLACE EACH ECU