Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › from 2018.08
RM2170E _53 Suspension _057019 TIRE PRESSURE MONITORING _0278018 TIRE PRESSURE WARNING SYSTEM D

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  DTC CHECK / CLEAR  


CHECK FOR DTC (for TIRE PRESSURE WARNING ECU AND RECEIVER) (USING GTS)


a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Tire Pressure Monitor / Trouble Codes.


f.

Read the DTCs.



CHECK FOR DTC (for TIRE PRESSURE WARNING ECU AND RECEIVER) (USING SST CHECK WIRE) (w/o Occupant Classification System)


C354379E01
1.677,1.104 1.677,0.583 false 1.896,2.24 1.896,1.719 false 0.125,0.115 0.438,0.313 0.313,0.198 10 false *1 0.75,2.938 1.063,3.135 0.313,0.198 10 false *2 1.573,0.354 1.927,0.594 0.354,0.24 10 false CG 1.813,2.302 2.125,2.5 0.313,0.198 10 false TC

C328265E01
0.188,0.146 0.5,0.344 0.313,0.198 10 false *a 1.167,0.563 1.479,0.76 0.313,0.198 10 false *d 0.24,0.896 0.552,1.094 0.313,0.198 10 false *b 0.271,1.365 0.583,1.563 0.313,0.198 10 false *c 1.271,1.719 1.583,1.917 0.313,0.198 10 false *d 0.104,2.5 0.417,2.698 0.313,0.198 10 false *e 1.375,2.479 1.688,2.677 0.313,0.198 10 false *h 0.365,2.76 0.677,2.958 0.313,0.198 10 false *f 0.906,2.75 1.219,2.948 0.313,0.198 10 false *g 0.448,3.927 0.76,4.125 0.313,0.198 10 false *h 1.479,3.948 1.792,4.146 0.313,0.198 10 false *f 2.813,3.979 3.125,4.177 0.313,0.198 10 false *j 2.063,2.75 2.375,2.948 0.313,0.198 10 false *i

a.

Turn the power switch off.


b.

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  


c.

Turn the power switch on (IG).


d.

Read and record any DTCs indicated by the tire pressure warning light on the combination meter assembly. Refer to the illustration for examples of a normal system code and codes 13 and 33.

HINT:
·

If the tire pressure warning light does not indicate any DTCs or the normal system code, inspect the tire pressure warning light circuit or TC and CG terminal circuit.

Trouble Area See page
Tire pressure warning light circuit (Click here)
TC and CG terminal circuit (Click here)

·

If 2 or more malfunctions are indicated at the same time, the lowest numbered DTC is displayed first.



Text in Illustration
*1 DLC3
*2 Tire Pressure Warning Light
*a Normal System Code
*b ON
*c OFF
*d 0.25 sec.
*e Code 13 and 33
*f 0.5 sec.
*g 2.5 sec.
*h 1.5 sec.
*i 4.5 sec.
*j Repeat


e.

Refer to Diagnostic Trouble Code Chart (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>DIAGNOSTIC TROUBLE CODE CHART) for DTC information.


f.

After completing the check, turn the power switch off and remove SST from the DLC3.



CHECK FOR DTC (for MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))


a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Main Body / Trouble Codes.


f.

Read the DTCs.



CLEAR DTC (for TIRE PRESSURE WARNING ECU AND RECEIVER)


HINT:

After repairing the malfunctions, clear the DTCs.


a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Tire Pressure Monitor / Trouble Codes.


f.

Clear the DTCs following the prompts on the GTS screen.

HINT:

Refer to the GTS operator's manual for further details.




CLEAR DTC (for MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))


HINT:

After repairing the malfunctions, clear the DTCs.


a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Main Body / Trouble Codes.


f.

Clear the DTCs following the prompts on the GTS screen.

HINT:

Refer to the GTS operator's manual for further details.