Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2019.07–2020.08
RM2170E _57 Power Source / Network _057033 NETWORKING _0278068 CAN COMMUNICATION SYSTEM U

NETWORKING  CAN COMMUNICATION SYSTEM  TERMINALS OF ECU  


NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Turn the power switch off before measuring the resistances between CAN main bus lines and between CAN branch lines.

·

Turn the power switch off before inspecting CAN bus lines for a ground short.

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

This section describes the standard values for all CAN related components.



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



CAN JUNCTION CONNECTOR LH (for LHD)


a.

Check the CAN junction connector LH (instrument panel wire side).

i.

Connection diagram

C251171C96
3.438,0.302 3.875,0.531 0.438,0.229 3.01,1.688 3.01,1 3.01,1 2.698,1 true 3.01,1.917 3.01,2.208 3.01,2.208 2.698,2.208 true 3.146,1.917 3.146,2.563 3.146,2.563 2.76,2.563 true 3.125,1.688 3.125,0.656 3.125,0.656 2.729,0.656 true 3.385,1.927 3.385,2.219 3.385,2.219 4.365,2.219 true 3.26,1.917 3.26,2.521 3.26,2.521 4.354,2.521 true 3.385,1.698 3.385,1 3.385,1 4.365,1 true 3.25,1.698 3.25,0.667 3.25,0.667 4.344,0.667 true 0.135,0.094 0.573,0.448 0.438,0.354 10 false *a 2.188,0.938 3.167,1.344 0.979,0.406 10 false CANH*b 2.188,2.146 2.958,2.406 0.771,0.26 10 false CANL*b 2.198,2.49 2.99,2.698 0.792,0.208 10 false CANL*c 2.177,0.594 2.906,0.906 0.729,0.313 10 false CANH*c 4.458,2.156 5.26,2.406 0.802,0.25 10 false CANL*e 4.458,2.458 5.281,2.688 0.823,0.229 10 false CANL*d 4.448,0.938 5.229,1.25 0.781,0.313 10 false CANH*e 4.448,0.604 5.354,0.885 0.906,0.281 10 false CANH*d 3.51,0.333 4.094,0.677 0.583,0.344 10 false G86
*a Front view of wire harness connector
(to CAN Junction Connector LH (Instrument Panel Wire Side))
*b to Vehicle Approaching Speaker Controller
(w/ Vehicle Proximity Notification System)
(for V Bus)
*c to Hybrid Vehicle Control Computer Assembly
(for V Bus)
*d to DLC3
(for V Bus)
*e to CAN Junction Connector RH
(for V Bus)
- -



ii.

Check the connection diagram of the components which are connected to the CAN junction connector LH.

Terminal No. (Symbol) Wiring Color Connected to
G86-1 (CANH) GR Vehicle approaching speaker controller*
(for V bus)
G86-12 (CANL) W
G86-2 (CANH) BE Hybrid vehicle control computer assembly
(for V bus)
G86-13 (CANL) W
G86-3 (CANH) GR DLC3
(for V bus)
G86-14 (CANL) W
G86-4 (CANH) SB CAN junction connector RH
(for V bus)
G86-15 (CANL) W

*: w/ Vehicle Proximity Notification System




b.

Check the CAN junction connector LH (engine room main wire side).

i.

Connection diagram

U183589E01
3.495,0.366 3.797,0.519 0.302,0.153 10 A74 5.026,1.117 5.584,1.279 0.557,0.162 10 CANH*c 5.026,2.063 5.584,2.225 0.557,0.162 10 CANL*c 4.118,1.663 4.118,1.188 4.118,1.188 5.001,1.188 false 4.906,0.845 5.464,1.007 0.557,0.162 10 CANH*b 3.998,1.664 3.998,0.916 3.998,0.916 4.881,0.916 false 0.052,0.019 0.228,0.181 0.176,0.162 10 *a 4.121,1.905 4.121,2.135 4.121,2.135 5.003,2.135 false 4.899,2.318 5.456,2.480 0.557,0.162 10 CANL*b 3.994,1.907 3.994,2.389 3.994,2.389 4.876,2.389 false

Text in Illustration
*a Front view of wire harness connector
(to CAN Junction Connector LH (Engine Room Main Wire Side))
*b to ECM
(for V Bus)
*c to Brake Booster with Master Cylinder Assembly (Skid Control ECU)
(for V Bus)
- -


ii.

Check the connection diagram of the components which are connected to the CAN junction connector LH.

Terminal No. (Symbol) Wiring Color Connected to
A74-9 (CANH) L ECM
(for V bus)
A74-20 (CANL) W
A74-10 (CANH) B Brake booster with master cylinder assembly (Skid control ECU)
(for V bus)
A74-21 (CANL) W




CAN JUNCTION CONNECTOR LH (for RHD)


a.

Check the CAN junction connector LH (instrument panel wire side).

i.

Connection diagram

U183588E01
3.495,0.372 3.778,0.526 0.283,0.153 10 G86 2.222,0.866 2.918,1.028 0.696,0.162 10 CANH*b 3.144,1.669 3.144,0.939 3.144,0.939 2.776,0.939 false 4.298,0.852 4.939,1.014 0.641,0.162 10 CANH*d 3.39,1.671 3.39,0.922 3.39,0.922 4.273,0.922 false 2.342,0.59 3.066,0.752 0.724,0.162 10 CANH*c 0.052,0.026 0.228,0.188 0.176,0.162 10 *a 3.264,1.666 3.264,0.663 3.264,0.663 2.896,0.663 false 2.242,2.304 2.917,2.459 0.676,0.156 10 CANL*b 3.144,1.913 3.144,2.374 3.144,2.374 2.776,2.374 false 2.366,2.525 2.958,2.680 0.592,0.156 10 CANL*c 3.268,1.912 3.268,2.594 3.268,2.594 2.9,2.594 false 4.291,2.324 4.987,2.486 0.696,0.162 10 CANL*d 3.386,1.913 3.386,2.395 3.386,2.395 4.268,2.395 false

Text in Illustration
*a Front view of wire harness connector
(to CAN Junction Connector LH (Instrument Panel Wire Side))
*b to Hybrid Vehicle Control Computer Assembly
(for V Bus)
*c to Smart Key ECU Assembly (Certification ECU)
(for V Bus)
*d to CAN Junction Connector RH
(for V Bus)


ii.

Check the connection diagram of the components which are connected to the CAN junction connector LH.

Terminal No. (Symbol) Wiring Color Connected to
G86-2 (CANH) BE Hybrid vehicle control computer assembly
(for V bus)
G86-13 (CANL) W
G86-3 (CANH) L Smart key ECU assembly (Certification ECU)
(for V bus)
G86-14 (CANL) W
G86-4 (CANH) SB CAN junction connector RH
(for V bus)
G86-15 (CANL) W



b.

Check the CAN junction connector LH (engine room main wire side).

i.

Connection diagram

C251171C97
3.417,0.219 3.844,0.458 0.427,0.24 4.229,1.906 4.229,2.188 4.229,2.188 4.396,2.188 true 3.979,1.917 3.979,2.5 3.979,2.5 4.167,2.5 true 4.104,1.698 4.104,0.781 4.104,0.781 4.271,0.781 true 3.969,1.688 3.969,0.604 3.969,0.604 4.135,0.604 true 4.104,1.906 4.104,2.323 4.104,2.323 4.271,2.323 true 4.219,1.698 4.219,0.979 4.219,0.979 4.365,0.979 true 0.115,0.083 0.542,0.365 0.427,0.281 10 false *a 4.26,2.448 5.063,2.75 0.802,0.302 10 false CANL*b 4.333,2.26 5.146,2.542 0.813,0.281 10 false CANL*c 4.344,0.719 5.198,1.115 0.854,0.396 10 false CANH*c 4.208,0.552 5.146,0.927 0.938,0.375 10 false CANH*b 3.51,0.25 4.031,0.583 0.521,0.333 10 false A74 4.469,2.115 5.281,2.396 0.813,0.281 10 false CANL*d 4.438,0.917 5.292,1.313 0.854,0.396 10 false CANH*d
*a Front view of wire harness connector
(to CAN Junction Connector LH (Engine Room Main Wire Side))
*b to ECM
(for V Bus)
*c to Brake Booster with Master Cylinder Assembly (Skid Control ECU)
(for V Bus)
*d to Headlight Leveling ECU Assembly
(w/ Automatic Headlight Beam Level Control System)
(for V Bus)



ii.

Check the connection diagram of the components which are connected to the CAN junction connector LH.

Terminal No. (Symbol) Wiring Color Connected to
A74-9 (CANH) L ECM
(for V bus)
A74-20 (CANL) W
A74-10 (CANH) B Brake booster with master cylinder assembly (Skid control ECU)
(for V bus)
A74-21 (CANL) W
A74-11 (CANH) P Headlight leveling ECU assembly*
(for V bus)
A74-22 (CANL) W

*: w/ Automatic Headlight Beam Level Control System





CAN JUNCTION CONNECTOR RH (for LHD)


a.

Check the CAN junction connector RH.

i.

Connection diagram

U183590E01
2.105,1.168 2.663,1.330 0.557,0.162 10 CANH*b 2.125,2.06 2.662,2.215 0.537,0.156 10 CANL*b 3.495,0.366 3.778,0.519 0.283,0.153 10 G72 3.027,1.661 3.027,1.241 3.027,1.241 2.659,1.241 false 2.346,0.86 2.903,1.022 0.557,0.162 10 CANH*c 4.784,0.795 5.342,0.957 0.557,0.162 10 CANH*g 4.784,2.349 5.342,2.511 0.557,0.162 10 CANL*g 3.268,1.663 3.268,0.933 3.268,0.933 2.9,0.933 false 3.876,1.663 3.876,0.87 3.876,0.87 4.759,0.87 false 5.026,1.382 5.583,1.544 0.557,0.162 10 CANH*i 4.118,1.66 4.118,1.452 4.118,1.452 5.001,1.452 false 4.679,0.621 5.236,0.783 0.557,0.162 10 CANH*f 3.756,1.664 3.756,0.683 3.756,0.683 4.639,0.683 false 2.452,0.696 3.009,0.858 0.557,0.162 10 CANH*d 0.052,0.019 0.228,0.181 0.176,0.162 10 *a 3.642,1.66 3.642,0.618 3.642,0.618 3.32,0.618 false 3.644,1.905 3.644,2.588 3.644,2.588 3.209,2.588 false 3.388,1.66 3.388,0.768 3.388,0.768 3.02,0.768 false 3.027,1.903 3.027,2.13 3.027,2.13 2.659,2.13 false 2.366,2.213 2.903,2.369 0.537,0.156 10 CANL*c 3.268,1.906 3.268,2.282 3.268,2.282 2.9,2.282 false 2.49,2.35 3.027,2.506 0.537,0.156 10 CANL*d 3.392,1.905 3.392,2.447 3.392,2.447 3.024,2.447 false 3.88,1.905 3.88,2.437 3.88,2.437 4.761,2.437 false 4.909,2.157 5.449,2.319 0.540,0.162 10 CANL*h 4.005,1.895 4.005,2.228 4.005,2.228 4.886,2.228 false 5.021,1.975 5.561,2.137 0.540,0.162 10 CANL*i 4.117,1.906 4.117,2.046 4.117,2.046 4.998,2.046 false 4.657,2.505 5.215,2.667 0.557,0.162 10 CANL*f 3.753,1.907 3.753,2.576 3.753,2.576 4.634,2.576 false 2.651,2.506 3.209,2.668 0.557,0.162 10 CANL*e 2.715,0.553 3.272,0.715 0.557,0.162 10 CANH*e 3.99,1.657 3.99,1.009 3.99,1.009 4.873,1.009 false 4.918,0.928 5.475,1.090 0.557,0.162 10 CANH*h

Text in Illustration
*a Front view of wire harness connector
(to CAN Junction Connector RH)
*b to Spiral Cable with Sensor Sub-assembly (Steering Sensor)
(for V Bus)
*c to Smart Key ECU Assembly (Certification ECU)
(for V Bus)
*d to Airbag Sensor Assembly
(for V Bus)
*e to Power Steering ECU Assembly
(for V Bus)
*f to Combination Meter Assembly
(for V Bus)
*g to Air Conditioning Amplifier Assembly
(for V Bus)
*h to Main Body ECU (Multiplex Network Body ECU)
(for V Bus)
*i to CAN Junction Connector LH
(for V Bus)
- -


ii.

Check the connection diagram of the components which are connected to the CAN junction connector RH.

Terminal No. (Symbol) Wiring Color Connected to
G72-1 (CANH) P Spiral cable with sensor sub-assembly (Steering sensor)
(for V bus)
G72-12 (CANL) W
G72-3 (CANH) L Smart key ECU assembly (Certification ECU)
(for V bus)
G72-14 (CANL) W
G72-4 (CANH) B Airbag sensor assembly
(for V bus)
G72-15 (CANL) W
G72-6 (CANH) LG Power steering ECU assembly
(for V bus)
G72-17 (CANL) W
G72-7 (CANH) G Combination meter assembly
(for V bus)
G72-18 (CANL) W
G72-8 (CANH) V Air conditioning amplifier assembly
(for V bus)
G72-19 (CANL) W
G72-9 (CANH) BE Main body ECU (Multiplex network body ECU)
(for V bus)
G72-20 (CANL) W
G72-10 (CANH) SB CAN junction connector LH
(for V bus)
G72-21 (CANL) W




CAN JUNCTION CONNECTOR RH (for RHD)


a.

Check the CAN junction connector RH.

i.

Connection diagram

U183591E01
2.105,1.322 2.663,1.484 0.557,0.162 10 CANH*b 2.125,2.06 2.662,2.215 0.537,0.156 10 CANL*b 3.495,0.366 3.778,0.519 0.283,0.153 10 G72 3.027,1.661 3.027,1.395 3.027,1.395 2.659,1.395 false 2.343,1.126 2.900,1.288 0.557,0.162 10 CANH*c 4.784,0.81 5.342,0.972 0.557,0.162 10 CANH*g 4.784,2.383 5.342,2.545 0.557,0.162 10 CANL*g 3.391,1.663 3.391,1.199 3.391,1.199 2.897,1.199 false 3.993,1.663 3.993,0.88 3.993,0.88 4.759,0.88 false 5.026,1.036 5.583,1.198 0.557,0.162 10 CANH*h 4.118,1.66 4.118,1.106 4.118,1.106 5.001,1.106 false 5.148,1.279 5.705,1.441 0.557,0.162 10 CANH*i 4.239,1.658 4.239,1.35 4.239,1.35 5.123,1.35 false 2.759,0.576 3.316,0.738 0.557,0.162 10 CANH*e 3.881,1.664 3.881,0.647 3.881,0.647 4.537,0.647 false 3.879,1.907 3.879,2.664 3.879,2.664 4.533,2.664 false 3.75,1.664 3.75,0.647 3.75,0.647 3.416,0.647 false 2.527,0.92 3.084,1.082 0.557,0.162 10 CANH*d 0.052,0.019 0.228,0.181 0.176,0.162 10 *a 3.631,1.66 3.631,0.993 3.631,0.993 3.081,0.993 false 3.027,1.903 3.027,2.13 3.027,2.13 2.659,2.13 false 2.348,2.213 2.885,2.369 0.537,0.156 10 CANL*c 3.39,1.906 3.39,2.283 3.39,2.283 2.938,2.283 false 2.593,2.378 3.130,2.534 0.537,0.156 10 CANL*d 3.635,1.905 3.635,2.448 3.635,2.448 3.127,2.448 false 3.993,1.905 3.993,2.454 3.993,2.454 4.761,2.454 false 5.021,2.178 5.561,2.340 0.540,0.162 10 CANL*h 4.117,1.906 4.117,2.249 4.117,2.249 4.998,2.249 false 5.145,1.966 5.685,2.128 0.540,0.162 10 CANL*i 4.24,1.906 4.24,2.037 4.24,2.037 5.121,2.037 false 2.836,2.593 3.393,2.755 0.557,0.162 10 CANL*e 3.753,1.907 3.753,2.664 3.753,2.664 3.419,2.664 false 4.587,0.58 5.144,0.742 0.557,0.162 10 CANH*f 4.601,2.585 5.159,2.747 0.557,0.162 10 CANL*f

Text in Illustration
*a Front view of wire harness connector
(to CAN Junction Connector RH)
*b to Spiral Cable with Sensor Sub-assembly (Steering Sensor)
(for V Bus)
*c to Airbag Sensor Assembly
(for V Bus)
*d to Power Steering ECU Assembly
(for V Bus)
*e to Combination Meter Assembly
(for V Bus)
*f to Air Conditioning Amplifier Assembly
(for V Bus)
*g to Main Body ECU (Multiplex Network Body ECU)
(for V Bus)
*h to CAN Junction Connector LH
(for V Bus)
*i to DLC3
(for V Bus)
- -


ii.

Check the connection diagram of the components which are connected to the CAN junction connector RH.

Terminal No. (Symbol) Wiring Color Connected to
G72-1 (CANH) P Spiral cable with sensor sub-assembly (Steering sensor)
(for V bus)
G72-12 (CANL) W
G72-4 (CANH) B Airbag sensor assembly
(for V bus)
G72-15 (CANL) W
G72-6 (CANH) LG Power steering ECU assembly
(for V bus)
G72-17 (CANL) W
G72-7 (CANH) G Combination meter assembly
(for V bus)
G72-18 (CANL) W
G72-8 (CANH) V Air conditioning amplifier assembly
(for V bus)
G72-19 (CANL) W
G72-9 (CANH) BE Main body ECU (Multiplex network body ECU)
(for V bus)
G72-20 (CANL) W
G72-10 (CANH) SB CAN junction connector LH
(for V bus)
G72-21 (CANL) W
G72-11 (CANH) GR DLC3
(for V bus)
G72-22 (CANL) W




CAN JUNCTION CONNECTOR LH


a.

Check the CAN junction connector LH (engine room main wire side).

i.

Connection diagram

U183592E02
3.49,1.688 3.49,0.771 3.49,0.771 3.323,0.771 false 3.75,1.906 3.75,2.323 3.75,2.323 3.917,2.323 false 3.74,1.688 3.74,0.771 3.74,0.771 3.906,0.771 false 3.5,1.896 3.5,2.313 3.5,2.313 3.333,2.313 false 3.5,0.365 3.781,0.521 0.281,0.156 10 false A74 3.969,0.698 4.521,0.865 0.552,0.167 10 false CANH*c 4.01,2.229 4.563,2.396 0.552,0.167 10 false CANL*c 2.75,0.688 3.302,0.854 0.552,0.167 10 false CANH*b 0.052,0.021 0.229,0.188 0.177,0.167 10 false *a 2.802,2.24 3.354,2.406 0.552,0.167 10 false CANL*b

Text in Illustration
*a Front view of wire harness connector
(to CAN Junction Connector LH (Engine Room Main Wire Side))
*b to Brake Booster with Master Cylinder Assembly (Skid Control ECU)
(for Sub Bus 15)
*c to ECM
(for Sub Bus 15)
- -


ii.

Check the connection diagram of the components which are connected to the CAN junction connector LH.

Terminal No. (Symbol) Wiring Color Connected to
A74-5 (CANH) L Brake booster with master cylinder assembly (Skid control ECU)
(for Sub bus 15)
A74-16 (CANL) W
A74-7 (CANH) B ECM
(for Sub bus 15)
A74-18 (CANL) W



b.

Check the CAN junction connector LH (instrument panel wire side).

i.

Connection diagram

U183593E02
3.49,1.698 3.49,0.781 3.49,0.781 3.323,0.781 false 3.5,1.906 3.5,2.323 3.5,2.323 3.333,2.323 false 3.5,0.365 3.781,0.521 0.281,0.156 10 false G86 2.771,0.708 3.323,0.875 0.552,0.167 10 false CANH*b 0.052,0.021 0.229,0.188 0.177,0.167 10 false *a 2.813,2.25 3.365,2.417 0.552,0.167 10 false CANL*b

Text in Illustration
*a Front view of wire harness connector
(to CAN Junction Connector LH (Instrument Panel Wire Side))
*b to Hybrid Vehicle Control Computer Assembly
(for Sub Bus 15)


ii.

Check the connection diagram of the components which are connected to the CAN junction connector LH.

Terminal No. (Symbol) Wiring Color Connected to
G86-5 (CANH) R Hybrid vehicle control computer assembly
(for Sub bus 15)
G86-16 (CANL) W




DLC3


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Measure the resistance according to the value(s) in the table below.

C188081C50
1.51,1.667 1.885,1.885 0.375,0.219 1.51,1.323 1.885,1.542 0.375,0.219 4.198,1.948 4.198,2.365 4.198,2.365 4.365,2.365 true 4,0.917 3.833,0.917 3.833,0.917 3.833,1.417 true 3.313,0.906 3.479,0.906 3.479,0.906 3.479,1.406 true 3.833,1.969 3.833,2.385 3.833,2.385 3.667,2.385 true 0.135,0.104 0.656,0.271 0.521,0.167 10 false *1 1.604,1.688 2.094,2.073 0.49,0.385 10 false G4 3.25,2.313 3.865,2.594 0.615,0.281 10 false CANL 4.083,0.844 4.74,1.146 0.656,0.302 10 false CANH 4.438,2.271 5.031,2.521 0.594,0.25 10 false BAT 3.063,0.833 3.573,1.125 0.51,0.292 10 false CG 1.573,1.354 2.063,1.74 0.49,0.385 10 false G93 1.99,1.344 2.479,1.729 0.49,0.385 12 false *A 1.99,1.677 2.479,2.063 0.49,0.385 12 false *B
*A for LHD *B for RHD
*1 DLC3 - -


Standard Resistance:
for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G93-6 (CANH) - G93-14 (CANL) GR - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
G93-6 (CANH) - G93-4 (CG) GR - P HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G93-14 (CANL) - G93-4 (CG) W - P LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G93-6 (CANH) - G93-16 (BAT) GR - SB HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
G93-14 (CANL) - G93-16 (BAT) W - SB LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G4-6 (CANH) - G4-14 (CANL) GR - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
G4-6 (CANH) - G4-4 (CG) GR - P HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G4-14 (CANL) - G4-4 (CG) W - P LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G4-6 (CANH) - G4-16 (BAT) GR - SB HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
G4-14 (CANL) - G4-16 (BAT) W - SB LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




HYBRID VEHICLE CONTROL COMPUTER ASSEMBLY


U183657E02
5.26,1.146 5.813,0.354 false 5.135,1.01 4.813,0.198 false 5.125,1.146 4.281,0.344 false 5.25,1.01 5.604,0.188 false 5.542,1.469 5.823,1.615 0.281,0.146 10 false G81 4.25,1.469 4.531,1.615 0.281,0.146 10 false G80 5.625,0.042 5.99,0.219 0.365,0.177 10 false CA1L 4.427,0.052 4.813,0.229 0.385,0.177 10 false CA1H 3.906,0.198 4.292,0.375 0.385,0.177 10 false CA3P 5.844,0.208 6.229,0.385 0.385,0.177 10 false CA3N 1.448,1.458 1.729,1.604 0.281,0.146 10 false A71 2.802,1.5 3.083,1.646 0.281,0.146 10 false A72 0.271,0.031 0.656,0.208 0.385,0.177 10 false *a

Text in Illustration
*a Component without harness connected
(Hybrid Vehicle Control Computer Assembly)
- -

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U183185E02
2.469,2.5 1.646,2.208 false 2.417,2.51 1.667,2.458 false 2.698,2.365 2.833,1.917 false 1.698,2.771 2.417,2.573 false 1.76,3.052 2.479,2.573 false 1.823,1.396 1.573,0.896 false 2.51,2.958 2.792,3.104 0.281,0.146 10 false G81 1.25,2.083 1.615,2.26 0.365,0.177 10 false CA1L 1.25,2.354 1.635,2.531 0.385,0.177 10 false CA1H 1.323,2.688 1.708,2.865 0.385,0.177 10 false CA3P 1.333,2.99 1.719,3.167 0.385,0.177 10 false CA3N 0.156,0.063 0.354,0.229 0.198,0.167 10 false *a 2.875,1.833 3.25,2.01 0.375,0.177 10 false BATT 1.354,0.75 1.542,0.896 0.188,0.146 10 false E1 1.917,0.75 2.198,0.896 0.281,0.146 10 false G80

Disconnect the G81 hybrid vehicle control computer assembly connector.

Text in Illustration
*a Rear view of wire harness connector
(to Hybrid Vehicle Control Computer Assembly)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
V Bus Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G81-25 (CA1H) - G81-24 (CA1L) BE - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
G81-25 (CA1H) - G80-6 (E1) BE - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G81-24 (CA1L) - G80-6 (E1) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G81-25 (CA1H) - G81-3 (BATT) BE - BE HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
G81-24 (CA1L) - G81-3 (BATT) W - BE LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Sub Bus 15 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G81-31 (CA3P) - G81-30 (CA3N) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
G81-31 (CA3P) - G80-6 (E1) R - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G81-30 (CA3N) - G80-6 (E1) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G81-31 (CA3P) - G81-3 (BATT) R - BE HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
G81-30 (CA3N) - G81-3 (BATT) W - BE LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




ECM


U183553E02
5.125,1.417 4.51,0.76 4.51,0.76 4.313,0.76 false 5.25,1.417 5.76,0.76 5.76,0.76 6.031,0.76 false 5.125,1.292 4.844,0.427 4.844,0.427 4.552,0.427 false 5.25,1.302 5.333,0.438 5.333,0.438 5.573,0.438 false 5.875,2.24 6.198,2.406 0.323,0.167 10 false A40 1.906,2.24 2.104,2.396 0.198,0.156 10 false C9 2.219,2.333 2.417,2.49 0.198,0.156 10 false *B 3.406,2.333 3.604,2.49 0.198,0.156 10 false *A 3.063,2.24 3.344,2.396 0.281,0.156 10 false C10 4.146,0.354 4.573,0.521 0.427,0.167 10 false CANH 5.604,0.365 6.031,0.531 0.427,0.167 10 false CANP 6.063,0.688 6.49,0.854 0.427,0.167 10 false CANN 3.917,0.698 4.344,0.865 0.427,0.167 10 false CANL 0.115,0.104 0.365,0.313 0.25,0.208 10 false *a

Text in Illustration
*A for LHD *B for RHD
*a Component without harness connected
(ECM)
- -

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A40 and C9 or C10 ECM connectors.

U183639E03
2.5,1.271 2.5,0.844 2.5,0.844 2.75,0.844 false 2.427,1.281 2.427,0.615 2.427,0.615 2.677,0.615 false 2.5,1.354 2.5,1.927 2.5,1.927 2.75,1.927 false 2.427,1.354 2.427,2.208 2.427,2.208 2.667,2.208 false 4.813,1.281 4.708,0.74 4.708,0.74 4.5,0.74 false 1.521,1.271 1.417,0.729 1.417,0.729 1.208,0.729 false 1.792,2.083 2.177,2.344 0.385,0.26 10 false A40 4.427,1.948 4.625,2.125 0.198,0.177 10 false C9 5.375,1.938 5.646,2.115 0.271,0.177 10 false C10 4.74,2.021 4.906,2.167 0.167,0.146 10 false *B 0.083,0.052 0.25,0.198 0.167,0.146 10 false *a 2.781,0.771 3.198,0.917 0.417,0.146 10 false CANH 4.302,0.667 4.51,0.823 0.208,0.156 10 false E1 2.719,0.531 3.135,0.677 0.417,0.146 10 false CANP 2.781,1.854 3.198,2 0.417,0.146 10 false CANL 2.708,2.135 3.125,2.281 0.417,0.146 10 false CANN 5.74,2.01 5.906,2.156 0.167,0.146 10 false *A 0.833,0.667 1.208,0.813 0.375,0.146 10 false BATT

Text in Illustration
*A for LHD *B for RHD
*a Front view of wire harness connector
(to ECM)
- -


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
V Bus Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A40-13 (CANH) - A40-26 (CANL) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
A40-13 (CANH) - C10-16 (E1)*1
A40-13 (CANH) - C9-16 (E1)*2
L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A40-26 (CANL) - C10-16 (E1)*1
A40-26 (CANL) - C9-16 (E1)*2
W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A40-13 (CANH) - A40-1 (BATT) L - Y HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A40-26 (CANL) - A40-1 (BATT) W - Y LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Sub Bus 15 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A40-12 (CANP) - A40-25 (CANN) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
A40-12 (CANP) - C10-16 (E1)*1
A40-12 (CANP) - C9-16 (E1)*2
B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A40-25 (CANN) - C10-16 (E1)*1
A40-25 (CANN) - C9-16 (E1)*2
W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A40-12 (CANP) - A40-1 (BATT) B - Y HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A40-25 (CANN) - A40-1 (BATT) W - Y LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher


*1: for LHD

*2: for RHD



BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU)


U159318E01
0.25,0.235 0.489,0.412 0.239,0.177 10 *a 3.462,0.696 3.735,0.852 0.272,0.156 10 A41 2.461,2.098 2.859,2.254 0.398,0.155 10 CA1L 4.09,2.098 4.488,2.254 0.398,0.155 10 CA2L 3.268,1.873 3.06,2.164 3.06,2.164 2.861,2.164 false 3.681,1.873 3.854,2.164 3.854,2.164 4.059,2.164 false 2.538,2.358 2.936,2.513 0.398,0.155 10 CA1H 4.032,2.358 4.430,2.513 0.398,0.155 10 CA2H 3.363,1.875 3.137,2.423 3.137,2.423 2.938,2.423 false 3.58,1.875 3.765,2.423 3.765,2.423 4.008,2.423 false

Text in Illustration
*a Component without harness connected
(Brake Booster with Master Cylinder Assembly (Skid Control ECU))
- -

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C354342E01
1.5,0.5 1.917,0.75 0.417,0.25 2.448,1.458 2.448,0.75 2.448,0.75 2.698,0.75 true 2.875,2.583 2.625,2.583 2.625,2.583 2.625,1.75 true 1.396,2.75 1.646,2.75 1.646,2.75 1.646,1.885 true 1.5,3 1.75,3 1.75,3 1.75,1.885 true 2.198,3 1.948,3 1.948,3 1.948,1.885 true 2.302,2.75 2.052,2.75 2.052,2.75 2.052,1.896 true 0.083,0.073 0.396,0.271 0.313,0.198 10 false *a 1.583,0.542 1.896,0.74 0.313,0.198 10 false A41 2.74,0.667 3.052,0.865 0.313,0.198 10 false BI 2.927,2.49 3.323,2.76 0.396,0.271 10 false GND 2.365,2.656 2.792,2.885 0.427,0.229 10 false CA1L 2.25,2.917 2.75,3.177 0.5,0.26 10 false CA1H 1,2.656 1.427,2.885 0.427,0.229 10 false CA2L 1.094,2.917 1.594,3.177 0.5,0.26 10 false CA2H

Disconnect the A41 brake booster with master cylinder assembly (skid control ECU) connector.

Text in Illustration
*a Front view of wire harness connector
(to Brake Booster with Master Cylinder Assembly (Skid Control ECU))


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
V Bus Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A41-37 (CA1H) - A41-38 (CA1L) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A41-37 (CA1H) - A41-28 (GND) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A41-38 (CA1L) - A41-28 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A41-37 (CA1H) - A41-14 (BI) B - W HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A41-38 (CA1L) - A41-14 (BI) W - W LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Sub Bus 15 Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A41-35 (CA2H) - A41-34 (CA2L) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A41-35 (CA2H) - A41-28 (GND) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A41-34 (CA2L) - A41-28 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A41-35 (CA2H) - A41-14 (BI) L - W HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A41-34 (CA2L) - A41-14 (BI) W - W LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




AIRBAG SENSOR ASSEMBLY


U159349E01
2.633,0.189 2.912,0.370 0.280,0.181 10 G18 3.924,0.189 4.211,0.370 0.287,0.181 10 M36 4.824,0.189 5.111,0.370 0.287,0.181 10 M37 0.059,0.064 0.222,0.217 0.163,0.153 10 *a 1.317,0.149 1.738,0.302 0.421,0.153 10 CANH 3.015,0.136 3.435,0.289 0.421,0.153 10 CANL 3.172,0.946 2.05,0.217 2.05,0.217 1.735,0.217 false 3.345,1.222 3.703,0.201 3.703,0.201 3.428,0.201 false

Text in Illustration
*a Component without harness connected
(Airbag Sensor Assembly)
- -

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the G18 airbag sensor assembly connector.

C188802C46
0.552,1.552 0.927,1.76 0.375,0.208 3.323,1.75 3.698,1.958 0.375,0.208 3.333,1.479 3.708,1.688 0.375,0.208 1.677,1.104 1.51,1.104 1.51,1.104 1.51,1.604 true 1.417,1.885 1.417,2.219 1.417,2.219 1.25,2.219 true 1.688,1.885 1.688,2.219 1.688,2.219 1.854,2.219 true 5.688,1.948 5.688,2.365 5.688,2.365 5.854,2.365 true 0.188,0.146 2.583,0.5 2.396,0.354 10 false *a 0.802,2.146 1.25,2.313 0.448,0.167 10 false CANL 1.76,1.021 2.208,1.188 0.448,0.167 10 false CANH 1.948,2.135 2.271,2.344 0.323,0.208 10 false E1 5.938,2.281 6.292,2.448 0.354,0.167 10 false BAT 0.615,1.573 1.063,1.865 0.448,0.292 10 false G18 3.396,0.146 4.656,0.49 1.26,0.344 10 false *1 3.427,1.771 3.854,2.042 0.427,0.271 10 false G4 3.385,1.5 3.813,1.771 0.427,0.271 10 false G93 3.76,1.75 4.188,2.021 0.427,0.271 12 false *B 3.75,1.49 4.177,1.76 0.427,0.271 12 false *A
*A for LHD *B for RHD
*1 DLC3 - -
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G18-13 (CANH) - G18-22 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
G18-13 (CANH) - G18-25 (E1) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G18-22 (CANL) - G18-25 (E1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G18-13 (CANH) - G93-16 (BAT) B - SB HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
G18-22 (CANL) - G93-16 (BAT) W - SB LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G18-13 (CANH) - G18-22 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
G18-13 (CANH) - G18-25 (E1) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G18-22 (CANL) - G18-25 (E1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G18-13 (CANH) - G4-16 (BAT) B - SB HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
G18-22 (CANL) - G4-16 (BAT) W - SB LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


U183416E03
4.052,1.021 4.052,0.615 4.052,0.615 4.167,0.615 false 1.677,1.417 1.927,1.417 false 0.719,2.656 1.031,2.656 false 1.625,0.854 1.625,0.427 1.625,0.427 1.802,0.427 false 1.677,4.604 1.677,4.938 1.677,4.938 1.573,4.938 false 1.76,4.604 1.76,4.938 1.76,4.938 1.865,4.938 false 4.219,0.542 4.604,0.854 0.385,0.313 10 false MB 3.448,7.896 3.813,8.208 0.365,0.313 10 false MB 0.375,2.469 0.74,2.625 0.365,0.156 10 false 3E*B 0.375,2.656 0.792,2.802 0.417,0.146 10 false 3F*C 5.042,5.208 5.25,5.344 0.208,0.135 10 false 3C 0.906,1.354 1.104,1.49 0.198,0.135 10 false 3D 0.146,0.094 0.344,0.229 0.198,0.135 10 false *A 5.042,3.833 5.24,3.99 0.198,0.156 10 false *B 5.615,3.833 5.813,4.01 0.198,0.177 10 false *C 1.833,5.198 2.031,5.333 0.198,0.135 10 false 3D 5.875,1.313 6.073,1.448 0.198,0.135 10 false 3B 1.833,6.573 2.031,6.708 0.198,0.135 10 false 3B 5.875,2 6.063,2.135 0.188,0.135 10 false 3A 5.083,6.563 5.271,6.698 0.188,0.135 10 false 3A 0.906,1.99 1.115,2.125 0.208,0.135 10 false 3C 1.948,1.344 2.24,1.479 0.292,0.135 10 false G59 1.833,0.354 2.125,0.49 0.292,0.135 10 false *1 5.344,3.854 5.573,3.99 0.229,0.135 10 false 3F 1.729,3.865 2.021,4 0.292,0.135 10 false G59 4.76,3.854 5.021,3.99 0.26,0.135 10 false 3E 1.896,4.854 2.604,5.073 0.708,0.219 10 false CANL 1.115,4.865 1.823,5.083 0.708,0.219 10 false CANH

Text in Illustration
*A Component without harness connected
(Main Body ECU (Multiplex Network Body ECU) with 1 connector)
*B for LHD
*C for RHD - -
*1 Main Body ECU (Multiplex Network Body ECU) - -

U183434E02
1.635,0.958 1.635,0.615 1.635,0.615 1.771,0.615 false 4.104,1.125 4.104,0.615 4.104,0.615 4.24,0.615 false 1.677,1.531 1.948,1.531 false 1.677,1.958 1.948,1.958 false 0.76,2.719 1.031,2.719 false 4.615,4.51 4.615,4.854 4.615,4.854 4.5,4.854 false 4.698,4.51 4.698,4.854 4.698,4.854 4.802,4.854 false 2.229,3.792 2.51,3.948 0.281,0.156 10 false G60 4.698,3.792 4.979,3.948 0.281,0.156 10 false G59 1.167,5.052 1.448,5.208 0.281,0.156 10 false 3D 3.927,5.052 4.208,5.208 0.281,0.156 10 false 3C 1.823,6.313 2.104,6.469 0.281,0.156 10 false 3B 3.479,7.563 3.76,7.719 0.281,0.156 10 false MB 4.938,6.313 5.219,6.469 0.281,0.156 10 false 3A 5.885,5.052 6.167,5.208 0.281,0.156 10 false 3F 0.146,0.083 0.427,0.24 0.281,0.156 10 false *A 1.813,0.552 2.094,0.708 0.281,0.156 10 false *1 1.969,1.469 2.26,1.625 0.292,0.156 10 false G59 1.969,1.885 2.26,2.042 0.292,0.156 10 false G60 4.281,0.542 4.563,0.698 0.281,0.156 10 false MB 5.875,1.417 6.156,1.573 0.281,0.156 10 false 3B 5.875,2.094 6.156,2.25 0.281,0.156 10 false 3A 0.906,1.417 1.188,1.573 0.281,0.156 10 false 3D 0.906,2.094 1.188,2.25 0.281,0.156 10 false 3C 0.552,2.656 0.771,2.813 0.219,0.156 10 false 3F 4.854,4.771 5.563,4.99 0.708,0.219 10 false CANL 4.063,4.781 4.573,5 0.51,0.219 10 false CANH

Text in Illustration
*A Component without harness connected
(Main Body ECU (Multiplex Network Body ECU) with 2 connectors)
- -
*1 Main Body ECU (Multiplex Network Body ECU) - -

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the G59 main body ECU (multiplex network body ECU) connector.

C250555C04
3.479,0.354 3.854,0.583 0.375,0.229 3.479,2.469 3.854,2.688 0.375,0.219 3.479,2.208 3.854,2.427 0.375,0.219 4.531,4.271 4.281,4.271 4.281,4.271 4.281,3.969 true 4.042,0.917 3.854,0.917 3.854,0.917 3.854,1.448 true 3.625,0.917 3.76,0.917 3.76,0.917 3.76,1.448 true 3.76,2.896 3.573,2.896 3.573,2.896 3.573,3.427 true 1.938,0.333 2.208,0.635 0.271,0.302 10 false *a 1.927,2.76 2.396,3.052 0.469,0.292 10 false *1 4.615,4.188 4.906,4.365 0.292,0.177 10 false BAT 3.521,0.396 4.24,0.833 0.719,0.438 10 false G59 3.563,2.5 4.083,2.74 0.521,0.24 10 false G4 3.208,0.844 3.875,1.073 0.667,0.229 10 false CANL 4.115,0.833 4.833,1.208 0.719,0.375 10 false CANH 3.854,2.823 4.26,3.073 0.406,0.25 10 false CG 3.542,2.25 4.063,2.49 0.521,0.24 10 false G93 3.917,2.229 4.438,2.469 0.521,0.24 12 false *A 3.917,2.49 4.438,2.729 0.521,0.24 12 false *B
*A for LHD *B for RHD
*1 DLC3 - -
*a Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G59-14 (CANH) - G59-13 (CANL) BE - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
G59-14 (CANH) - G93-4 (CG) BE - P HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G59-13 (CANL) - G93-4 (CG) W - P LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G59-14 (CANH) - G93-16 (BAT) BE - SB HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
G59-13 (CANL) - G93-16 (BAT) W - SB LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G59-14 (CANH) - G59-13 (CANL) BE - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
G59-14 (CANH) - G4-4 (CG) BE - P HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G59-13 (CANL) - G4-4 (CG) W - P LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G59-14 (CANH) - G4-16 (BAT) BE - SB HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
G59-13 (CANL) - G4-16 (BAT) W - SB LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY (STEERING SENSOR)


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U159561E01
1.591,1.067 1.873,1.215 0.282,0.147 10 G30 0.41,1.322 0.724,1.470 0.314,0.147 10 ESS 0.844,2.677 1.242,2.824 0.398,0.147 10 CANL 2.192,2.672 2.633,2.819 0.440,0.147 10 CANH 2.671,1.322 2.967,1.470 0.296,0.147 10 BAT 0.06,0.038 0.217,0.185 0.158,0.147 10 *a 1.376,2.095 1.055,1.402 1.055,1.402 0.791,1.402 false 2.364,2.105 2.364,1.396 2.364,1.396 2.654,1.396 false 1.639,2.317 1.505,2.752 1.505,2.752 1.32,2.752 false 1.88,2.317 1.962,2.752 1.962,2.752 2.178,2.752 false

Disconnect the G30 spiral cable with sensor sub-assembly (steering sensor) connector.

Text in Illustration
*a Front view of wire harness connector
(to Spiral Cable with Sensor Sub-assembly (Steering Sensor))


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G30-4 (CANH) - G30-3 (CANL) P - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
G30-4 (CANH) - G30-2 (ESS) P - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G30-3 (CANL) - G30-2 (ESS) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G30-4 (CANH) - G30-6 (BAT) P - B HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
G30-3 (CANL) - G30-6 (BAT) W - B LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




POWER STEERING ECU ASSEMBLY


U183538E02
1.531,1.479 1.052,1.479 false 1.719,1.448 1.969,0.729 1.969,0.729 2.25,0.729 false 1.677,2.031 1.875,2.177 0.198,0.146 10 false G6 2.375,2.031 2.542,2.177 0.167,0.146 10 false z7 3.427,2.031 3.594,2.177 0.167,0.146 10 false z8 4.885,2.031 5.156,2.177 0.271,0.146 10 false A33 0.135,0.083 0.302,0.25 0.167,0.167 10 false *a 0.646,1.396 1.063,1.552 0.417,0.156 10 false CANL 2.271,0.646 2.688,0.802 0.417,0.156 10 false CANH

Text in Illustration
*a Component without harness connected
(Power Steering ECU Assembly)
- -

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A33 and G6 power steering ECU assembly connectors.

U159559E03
1.865,1.906 2.323,1.906 false 1.729,1.875 2.083,1.531 2.083,1.531 2.292,1.531 false 4.802,1.531 4.354,1.531 false 6.135,1.531 5.688,1.531 false 1.531,2.313 2.01,2.625 0.479,0.313 10 false G6 0.198,0.115 0.365,0.271 0.167,0.156 10 false *a 2.385,1.833 3.104,2.115 0.719,0.281 10 false CANL 2.354,1.458 3.146,1.729 0.792,0.271 10 false CANH 4.073,1.458 4.521,1.698 0.448,0.24 10 false PIG 6.198,1.448 6.802,1.677 0.604,0.229 10 false PGND 5.188,2.302 5.615,2.542 0.427,0.24 10 false A33

Text in Illustration
*a Front view of wire harness connector
(to Power Steering ECU Assembly)
- -


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G6-7 (CANH) - G6-8 (CANL) LG - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
G6-7 (CANH) - A33-2 (PGND) LG - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G6-8 (CANL) - A33-2 (PGND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G6-7 (CANH) - A33-1 (PIG) LG - W HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
G6-8 (CANL) - A33-1 (PIG) W - W LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




SMART KEY ECU ASSEMBLY (CERTIFICATION ECU)


U183377E02
4.802,1.49 4.406,0.385 4.406,0.385 4.229,0.385 false 4.719,1.479 4.417,0.688 4.417,0.688 4.24,0.688 false 1.938,0.865 2.323,1.021 0.385,0.156 10 false G77 3.313,0.865 3.677,1.021 0.365,0.156 10 false G78 4.854,0.865 5.281,1.021 0.427,0.156 10 false G79 3.813,0.615 4.208,0.771 0.396,0.156 10 false CANL 3.792,0.302 4.229,0.458 0.438,0.156 10 false CANH 0.198,0.094 0.479,0.25 0.281,0.156 10 false *a

Text in Illustration
*a Component without harness connected
(Smart Key ECU Assembly (Certification ECU))
- -

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U183540E01
0.131,0.137 0.350,0.330 0.220,0.194 10 *a 0.658,0.854 0.881,1.029 0.223,0.175 10 +B 2.566,1.176 2.716,1.358 0.150,0.182 10 E 2.242,1.261 2.526,1.261 false 0.906,0.939 1.19,0.939 false 1.532,2.08 1.952,2.231 0.420,0.152 10 G79 1.547,0.264 1.974,0.421 0.427,0.157 10 G77 0.492,1.994 1.048,2.177 0.557,0.183 10 CANH 1.051,2.092 1.279,2.092 1.279,2.092 1.501,3.086 false 1.035,2.31 1.219,2.31 1.219,2.31 1.409,3.082 false 0.482,2.233 1.039,2.416 0.557,0.183 10 CANL

Disconnect the G77 and G79 smart key ECU assembly (certification ECU) connectors.

Text in Illustration
*a Rear view of wire harness connector
(to Smart Key ECU Assembly (Certification ECU))


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G79-14 (CANH) - G79-15 (CANL) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
G79-14 (CANH) - G77-11 (E) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G79-15 (CANL) - G77-11 (E) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G79-14 (CANH) - G77-2 (+B) L - B HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
G79-15 (CANL) - G77-2 (+B) W - B LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




COMBINATION METER ASSEMBLY


U159502E01
2.198,0.255 2.403,0.408 0.205,0.153 10 G1 5.08,0.255 5.285,0.408 0.205,0.153 10 G3 0.077,0.058 0.282,0.212 0.205,0.153 10 *a 1.443,1.378 1.846,1.531 0.403,0.153 10 CANL 2.529,1.376 2.959,1.529 0.430,0.153 10 CANH 2.127,1.004 2.008,1.445 2.008,1.445 1.836,1.445 false 2.242,1.004 2.307,1.445 2.307,1.445 2.514,1.445 false

Text in Illustration
*a Component without harness connected
(Combination Meter Assembly)
- -

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U159532E01
1.619,0.754 1.825,0.907 0.206,0.153 10 G1 0.097,0.075 0.255,0.227 0.158,0.152 10 *a 0.223,1.599 0.333,1.751 0.110,0.152 10 B 0.975,2.91 1.403,3.062 0.429,0.152 10 CANH 2.25,2.904 2.679,3.056 0.429,0.152 10 CANL 3.081,1.601 3.292,1.753 0.211,0.152 10 ET 0.642,2.366 0.515,1.682 0.515,1.682 0.353,1.682 false 2.839,2.366 2.839,1.682 2.839,1.682 3.059,1.682 false 1.801,2.634 1.698,2.992 1.698,2.992 1.497,2.992 false 1.914,2.634 2.031,2.992 2.031,2.992 2.231,2.992 false

Disconnect the G1 combination meter assembly connector.

Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Assembly)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G1-31 (CANH) - G1-32 (CANL) G - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
G1-31 (CANH) - G1-20 (ET) G - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G1-32 (CANL) - G1-20 (ET) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G1-31 (CANH) - G1-1 (B) G - L HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
G1-32 (CANL) - G1-1 (B) W - L LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




AIR CONDITIONING AMPLIFIER ASSEMBLY


U159655E03
2.885,0.875 2.74,0.292 2.74,0.292 2.469,0.292 false 3.052,0.885 3.271,0.302 3.271,0.302 3.583,0.302 false 5.177,1.469 5.5,1.667 0.323,0.198 10 false z1 2.979,1.469 3.375,1.677 0.396,0.208 10 false G34 0.104,0.021 0.427,0.24 0.323,0.219 10 false *a 2.073,0.219 2.708,0.427 0.635,0.208 10 false CANL 3.635,0.229 4.302,0.479 0.667,0.25 10 false CANH

Text in Illustration
*a Component without harness connected
(Air Conditioning Amplifier Assembly)
- -

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U159533E01
1.566,0.754 1.847,0.907 0.282,0.153 10 G34 0.097,0.075 0.255,0.227 0.158,0.152 10 *a 0.118,2.506 0.229,2.658 0.110,0.152 10 B 0.814,1.371 1.243,1.522 0.429,0.152 10 CANH 2.298,1.366 2.727,1.518 0.429,0.152 10 CANL 2.743,1.662 3.070,1.814 0.327,0.152 10 GND 1.801,2.377 1.622,1.459 1.622,1.459 1.327,1.459 false 1.914,2.375 1.996,1.449 1.996,1.449 2.276,1.449 false 2.145,2.361 2.424,1.748 2.424,1.748 2.705,1.748 false 0.58,2.583 0.244,2.583 false

Disconnect the G34 air conditioning amplifier assembly connector.

Text in Illustration
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G34-11 (CANH) - G34-12 (CANL) V - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
G34-11 (CANH) - G34-14 (GND) V - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G34-12 (CANL) - G34-14 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G34-11 (CANH) - G34-21 (B) V - BE HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
G34-12 (CANL) - G34-21 (B) W - BE LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




VEHICLE APPROACHING SPEAKER CONTROLLER (w/ Vehicle Proximity Notification System)


B345454C04
1.573,0.885 1.979,1.115 0.406,0.229 3.521,0.26 3.688,0.26 3.688,0.26 3.688,1.01 true 4.063,0.26 3.896,0.26 3.896,0.26 3.896,1.01 true 0.167,0.115 0.479,0.313 0.313,0.198 10 false *a 1.656,0.917 1.969,1.115 0.313,0.198 10 false G97 4.156,0.198 4.813,0.396 0.656,0.198 10 false CANH 3.146,0.198 3.802,0.396 0.656,0.198 10 false CANL
*a Component without harness connected
(Vehicle Approaching Speaker Controller)
- -


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the G97 vehicle approaching speaker controller connector.

C398277C14
4.99,0.281 5.438,0.51 0.448,0.229 1.865,0.344 2.313,0.573 0.448,0.229 1.688,2 1.854,2 1.854,2 1.854,1.583 true 2.438,2.01 2.271,2.01 2.271,2.01 2.271,1.594 true 1.833,2.25 2,2.25 2,2.25 2,1.583 true 6,2.083 5.833,2.083 5.833,2.083 5.833,1.667 true 3.552,0.292 3.865,0.49 0.313,0.198 10 false *1 0.958,0.313 1.271,0.51 0.313,0.198 10 false *a 1.948,0.375 2.333,0.625 0.385,0.25 10 false G97 5.073,0.323 5.458,0.573 0.385,0.25 10 false G93 2.5,1.927 3.115,2.167 0.615,0.24 10 false GND 1.25,1.927 1.781,2.167 0.531,0.24 10 false CANH 1.427,2.167 1.958,2.406 0.531,0.24 10 false CANL 6.052,2 6.583,2.24 0.531,0.24 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to Vehicle Approaching Speaker Controller)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G97-3 (CANH) - G97-4 (CANL) GR - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
G97-3 (CANH) - G97-6 (GND) GR - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G97-4 (CANL) - G97-6 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G97-3 (CANH) - G93-16 (BAT) GR - SB HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
G97-4 (CANL) - G93-16 (BAT) W - SB LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




HEADLIGHT LEVELING ECU ASSEMBLY (w/ Automatic Headlight Beam Level Control System)


E208529C06
0.896,0.76 1.333,1.042 0.438,0.281 2.604,0.406 2.771,0.406 2.771,0.406 2.771,0.906 true 3.104,0.406 2.938,0.406 2.938,0.406 2.938,0.906 true 1,0.823 1.458,1.021 0.458,0.198 10 false A34 0.135,0.188 0.594,0.385 0.458,0.198 10 false *a 2.229,0.354 2.688,0.552 0.458,0.198 10 false CANL 3.188,0.354 3.646,0.552 0.458,0.198 10 false CANH
*a Component without harness connected
(Headlight Leveling ECU Assembly)
- -


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A34 headlight leveling ECU assembly connector.

C286973C18
4.917,0.75 5.323,1 0.406,0.25 1.885,0.896 2.26,1.167 0.375,0.271 6.219,2.26 5.948,2.26 5.948,2.26 5.698,1.969 true 2.813,1.604 3.146,1.604 true 2.573,1.563 2.833,1.177 2.833,1.177 3.042,1.177 true 2.469,1.563 2.906,0.896 2.906,0.896 3.083,0.896 true 0.906,0.583 1.26,0.875 0.354,0.292 10 false *a 6.281,2.167 6.771,2.51 0.49,0.344 10 false BAT 3.125,0.802 3.74,1.063 0.615,0.26 10 false CANH 3.094,1.083 3.708,1.344 0.615,0.26 10 false CANL 3.188,1.51 3.802,1.771 0.615,0.26 10 false E1 1.958,0.948 2.417,1.146 0.458,0.198 10 false A34 5.042,0.792 5.406,1.094 0.365,0.302 10 false G4 3.677,0.615 4.031,0.906 0.354,0.292 10 false *1
*1 DLC3 - -
*a Front view of wire harness connector
(to Headlight Leveling ECU Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A34-6 (CANH) - A34-7 (CANL) P - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A34-6 (CANH) - A34-9 (E1) P - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A34-7 (CANL) - A34-9 (E1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A34-6 (CANH) - G4-16 (BAT) P - SB HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A34-7 (CANL) - G4-16 (BAT) W - SB LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher