Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2019.07
RM2170E _57 Power Source / Network _057033 NETWORKING _0278068 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Vehicle Approaching Sound ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Vehicle Approaching Sound ECU Communication Stop Mode Either condition is met:
·

"Vehicle Proximity Notification System" is not displayed on the CAN Bus Check screen of the GTS.

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Vehicle Approaching Sound ECU Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Vehicle approaching speaker controller branch line or connector

·

Power source circuit of vehicle approaching speaker controller

·

Vehicle approaching speaker controller ground circuit

·

Vehicle approaching speaker controller



WIRING DIAGRAM

C418743E01
2.375,1.281 2.24,0.938 2.24,0.938 2.104,0.938 false 4.219,1.292 3.823,0.594 3.823,0.594 3.531,0.594 false 6.219,2.854 6.552,3.021 0.333,0.167 10 false ECM 2.875,4.063 3.24,4.375 0.365,0.313 10 false G97 3.198,4.063 5.052,4.635 1.854,0.573 10 false Vehicle Approaching Speaker Controller 4.76,0.563 5.135,0.74 0.375,0.177 10 false DLC3 1.146,5.01 3.073,5.365 1.927,0.354 10 false : CAN Main Bus Line (CANH) 4.292,5.021 6.031,5.375 1.74,0.354 10 false : CAN Branch Line (CANH) 4.281,5.427 6.021,5.781 1.74,0.354 10 false : CAN Branch Line (CANL) 1.125,5.438 3.052,5.792 1.927,0.354 10 false : CAN Main Bus Line (CANL) 2.479,3.74 3.615,4.073 1.135,0.333 10 false GAUGE 1.25,3.74 2.104,3.948 0.854,0.208 10 false Trouble Area 3.406,3.583 3.76,3.885 0.354,0.302 10 false IG 4.427,3.583 4.813,3.865 0.385,0.281 10 false GND 3.625,3.302 4.073,3.552 0.448,0.25 10 false CANH 4.104,3.302 4.521,3.542 0.417,0.24 10 false CANL 3.188,3.458 3.417,3.792 0.229,0.333 10 false 1 4.823,3.469 5.042,3.865 0.219,0.396 10 false 6 3.698,3.073 3.958,3.479 0.26,0.406 10 false 3 4.323,3.073 4.49,3.396 0.167,0.323 10 false 4 0.323,0.844 2.146,1.031 1.823,0.188 10 false CAN Junction Connector RH 0.167,0.125 1.417,0.354 1.25,0.229 12 false V Bus (for LHD): 1.76,0.51 3.771,0.698 2.01,0.188 10 false CAN Junction Connector LH 0.292,2.875 1.5,3.219 1.208,0.344 10 false Combination Meter Assembly 0.646,2.219 1.094,2.365 0.448,0.146 10 false 120 Ω 6.177,2.25 6.625,2.396 0.448,0.146 10 false 120 Ω

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (VEHICLE APPROACHING SPEAKER CONTROLLER BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the G97 vehicle approaching speaker controller connector.


c.
C394468C40
1.479,0.135 1.99,0.354 0.51,0.219 1.313,1.771 1.479,1.771 1.479,1.771 1.479,1.354 true 1.813,1.781 1.646,1.781 1.646,1.781 1.646,1.365 true 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a 1.604,0.167 2.094,0.385 0.49,0.219 10 false G97 0.875,1.698 1.365,1.917 0.49,0.219 10 false CANH 1.896,1.688 2.385,1.906 0.49,0.219 10 false CANL
*a Front view of wire harness connector
(to Vehicle Approaching Speaker Controller)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G97-3 (CANH) - G97-4 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C394468C41
1.479,0.135 1.99,0.354 0.51,0.219 0.969,1.771 1.135,1.771 1.135,1.771 1.135,1.354 true 2.156,1.781 1.99,1.781 1.99,1.781 1.99,1.365 true 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a 1.604,0.167 2.094,0.385 0.49,0.219 10 false G97 0.771,1.708 1.26,1.927 0.49,0.219 10 false IG 2.229,1.719 2.719,1.938 0.49,0.219 10 false GND
*a Front view of wire harness connector
(to Vehicle Approaching Speaker Controller)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G97-6 (GND) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G97-1 (IG) - Body ground Power switch on (IG) 11 to 14 V



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)