Home › Vehicle Exterior › LIGHTING (EXT) › AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM › from 2019.07
RM2170E _59 Vehicle Exterior _057049 LIGHTING (EXT) _0278195 AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM J

LIGHTING (EXT)  AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM  Headlight Beam Level Control Actuator Circuit  


DESCRIPTION

The headlight leveling ECU assembly operate the headlight leveling motors according to the vehicle conditions.

WIRING DIAGRAM

E378648E07
0.948,0.208 1.469,0.427 0.521,0.219 10 false 12 V 4.688,0.708 5.823,1.25 1.135,0.542 10 false Headlight Leveling Motor LH 4.688,2.781 5.823,3.219 1.135,0.438 10 false Headlight Leveling Motor RH 4.417,1.646 4.875,1.844 0.458,0.198 10 false A57 4.417,1.813 6.406,2.01 1.99,0.198 10 false Headlight Assembly LH 4.427,3.656 4.885,3.854 0.458,0.198 10 false A56 4.427,3.823 6.417,4.021 1.99,0.198 10 false Headlight Assembly RH 3.677,0.479 4.292,0.677 0.615,0.198 10 false LHIG 3.677,0.781 4.292,0.979 0.615,0.198 10 false LH T 3.677,1.073 4.292,1.271 0.615,0.198 10 false LH E 3.458,0.49 3.615,0.688 0.156,0.198 10 false 3 3.458,0.781 3.615,0.979 0.156,0.198 10 false 2 3.458,1.083 3.615,1.281 0.156,0.198 10 false 1 1.906,0.479 2.219,0.677 0.313,0.198 10 false 11 1.906,0.781 2.219,0.979 0.313,0.198 10 false 18 1.917,1.083 2.229,1.281 0.313,0.198 10 false 24 1.531,0.479 1.885,0.771 0.354,0.292 10 false LH+ 1.531,0.781 2.146,0.979 0.615,0.198 10 false LHT 1.552,1.083 2.167,1.281 0.615,0.198 10 false LH- 3.688,2.5 4.302,2.698 0.615,0.198 10 false RHIG 3.688,2.802 4.302,3 0.615,0.198 10 false RH T 3.688,3.094 4.302,3.292 0.615,0.198 10 false RH E 3.458,2.5 3.615,2.698 0.156,0.198 10 false 3 3.458,2.792 3.615,2.99 0.156,0.198 10 false 2 3.448,3.104 3.604,3.302 0.156,0.198 10 false 1 1.906,2.5 2.219,2.698 0.313,0.198 10 false 10 1.906,2.802 2.219,3 0.313,0.198 10 false 17 1.917,3.094 2.229,3.292 0.313,0.198 10 false 23 1.531,2.5 1.99,2.698 0.458,0.198 10 false RH+ 1.531,2.802 1.99,3 0.458,0.198 10 false RHT 1.552,3.104 2.01,3.302 0.458,0.198 10 false RH- 0.313,3.656 0.771,3.854 0.458,0.198 10 false A34 0.313,3.833 2.573,4.083 2.26,0.25 10 false Headlight Leveling ECU Assembly 0.927,2.229 1.448,2.448 0.521,0.219 10 false 12 V

CAUTION / NOTICE / HINT

NOTICE:

If the headlight leveling ECU assembly has been replaced, it is necessary to initialize the headlight leveling ECU assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM>INITIALIZATION


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (READY).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / HL AutoLeveling / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > HL AutoLeveling > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Drive The Leveling Motor Headlight leveling motor upward or downward operation Stop/Down/Up Perform the Active Test with the power switch on (READY) and vehicle stopped

OK:

Headlight leveling motors operate normally.



Result:
Result Proceed to
OK A
NG (for LH Side) B
NG (for RH Side) C



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY LH - HEADLIGHT LEVELING ECU ASSEMBLY)

C

5.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY RH - HEADLIGHT LEVELING ECU ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY LH - HEADLIGHT LEVELING ECU ASSEMBLY)
a.

Disconnect the A34 headlight leveling ECU assembly connector.


b.

Disconnect the A57 headlight assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A34-11 (LH+) - A57-3 (LHIG) Always Below 1 Ω
A34-18 (LHT) - A57-2 (LH T) Always Below 1 Ω
A34-24 (LH-) - A57-1 (LH E) Always Below 1 Ω
A34-11 (LH+) or A57-3 (LHIG) - Body ground Always 10 kΩ or higher
A34-18 (LHT) or A57-2 (LH T) - Body ground Always 10 kΩ or higher
A34-24 (LH-) or A57-1 (LH E) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HEADLIGHT ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HEADLIGHT ASSEMBLY LH
a.

Interchange the headlight unit assembly LH with RH and connect the connectors.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Headlight)>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK HEADLIGHT LEVELING MOTOR LH
4.CHECK HEADLIGHT LEVELING MOTOR LH
a.

Connect all of the disconnected connectors.


b.

Disconnect the headlight leveling motor LH connector.


Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

NG

5.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY RH - HEADLIGHT LEVELING ECU ASSEMBLY)
a.

Disconnect the A34 headlight leveling ECU assembly connector.


b.

Disconnect the A56 headlight assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A34-10 (RH+) - A56-3 (RHIG) Always Below 1 Ω
A34-17 (RHT) - A56-2 (RH T) Always Below 1 Ω
A34-23 (RH-) - A56-1 (RH E) Always Below 1 Ω
A34-10 (RH+) or A56-3 (RHIG) - Body ground Always 10 kΩ or higher
A34-17 (RHT) or A56-2 (RH T) - Body ground Always 10 kΩ or higher
A34-23 (RH-) or A56-1 (RH E) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HEADLIGHT ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HEADLIGHT ASSEMBLY RH
a.

Interchange the headlight unit assembly RH with LH and connect the connectors.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Headlight)>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK HEADLIGHT LEVELING MOTOR RH
7.CHECK HEADLIGHT LEVELING MOTOR RH
a.

Connect all of the disconnected connectors.


b.

Disconnect the headlight leveling motor RH connector.


Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

NG