Home › Vehicle Exterior › MIRROR (EXT) › OUTER REAR VIEW MIRROR › from 2019.07
RM2170E _59 Vehicle Exterior _057047 MIRROR (EXT) _0278168 OUTER REAR VIEW MIRROR A

MIRROR (EXT)  OUTER REAR VIEW MIRROR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.INSTALL OUTER MIRROR RETRACTOR (for Bulb Type Turn Signal Light)

w/ Power Retractable Mirror:

a.

Install a new retractor assembly with the screw.

B592570C01
0.323,3.25 0.635,3.406 0.313,0.156 10 false *a 2.521,3.25 2.833,3.406 0.313,0.156 10 false *b 4.771,3.25 5.083,3.406 0.313,0.156 10 false *c 2.031,3.792 2.188,3.99 0.156,0.198 10 false A 4.177,3.938 4.333,4.135 0.156,0.198 10 false A 6.448,3.844 6.604,4.042 0.156,0.198 10 false B
*a Screw Seated *b Screw Not Seated (Not fully tightened)
*c Screw Not Seated (Incorrect screw) - -


Screw Length:
A B
12 mm (0.472 in.) 14 mm (0.551 in.)


NOTICE:
·

When using a screw with a length of 12 mm, make sure to tighten it until it is fully seated.

·

Do not mistakenly use a screw with a length of 14 mm.




b.
B411117

Connect the connector.

NOTICE:

Make sure to replace the wire harness with a new one.



c.

Engage the clamp.


d.
B411118

Pass the wire harness through the visor body as shown in the illustration.


e.
B411119

Connect the connector.


f.

Engage the 2 clamps.


g.
B411120

Pass the wire harness through the retractor assembly as shown in the illustration.


h.
B308831

Install the reinforcement with the 5 screws.


i.
B308829

Install the unit drive assembly with the 3 screws.

NOTICE:

When installing the unit drive assembly, check that the wire harness is not caught.



j.
B308828

Pass the wire harness through the stay, install the stay with 3 new screws.

NOTICE:

When installing the stay, check that the wire harness is not caught between the stay and visor body. Failure to do so may cause a short circuit.



k.
B308827

Engage the 4 claws to install a new stay cover.


l.
B308826

Pass the wire harness through a new gasket, engage the 7 guides and 2 claws to install a new gasket.

NOTICE:

Do not make gaps between the gasket and stay.



m.
B308836E01
2.217,1.993 2.347,2.140 0.130,0.147 10 A 2.32,1.702 2.661,1.381 false 2.685,1.284 2.868,1.430 0.183,0.147 10 *1

Wrap new vinyl tape as shown in the illustration.

Text in Illustration
*1 Vinyl Tape

Area Measurement
A 45 mm (1.77 in.)

NOTICE:

Wrap the vinyl tape tightly around the wire harness to ensure that there are no gaps.



n.
B308837

Connect the connector of the shorter wire harness to the adapter.


o.

Twist the longer wire harness as shown in the illustration and connect the connector to the adapter.


Hide 81740 2.INSTALL SIDE TURN SIGNAL LIGHT ASSEMBLY (for Bulb Type Turn Signal Light)

Hide 81740 3.INSTALL SIDE TURN SIGNAL LIGHT ASSEMBLY (for LED Type Turn Signal Light)

Hide 8794A 4.INSTALL NO. 2 OUTER MIRROR COVER (for LED Type Turn Signal Light)

a.
E421427

Engage the 2 guides and 3 claws to temporarily install the No. 2 outer mirror cover.


b.

Install the No. 2 outer mirror cover with the screw.