Home › Vehicle Exterior › ACOUSTIC VEHICLE ALERTING SYSTEM › ACOUSTIC VEHICLE ALERTING SYSTEM › from 2020.08
RM2170E _59 Vehicle Exterior _092812 ACOUSTIC VEHICLE ALERTING SYSTEM _0437693 ACOUSTIC VEHICLE ALERTING SYSTEM C

ACOUSTIC VEHICLE ALERTING SYSTEM  ACOUSTIC VEHICLE ALERTING SYSTEM  B1350  Speaker Circuit  


DESCRIPTION

The vehicle approaching speaker assembly circuit consists of the vehicle approaching speaker controller and vehicle approaching speaker assembly.

This DTC is stored when a malfunction is detected in the vehicle approaching speaker assembly circuit or vehicle approaching speaker controller.

DTC No. Detection Item DTC Detecting Condition Trouble Area
B1350 Speaker Circuit
Detection condition(1):

The power switch is on (IG).


Detection condition(2):

IG power source voltage is 10 V or more.


Malfunction status(1):

When ECU output sound signal is being monitored with warning sound not being output, a speaker circuit open, short to auxiliary battery positive terminal or short to ground is detected.


Malfunction status(2):

When vehicle proximity warning sound output conditions are met, an internal malfunction is continuously detected in the vehicle approaching speaker controller.


Malfunction duration(1):

6 seconds or more


Malfunction duration(2):

3 seconds or more


·

Vehicle approaching speaker controller

·

Vehicle approaching speaker assembly

·

Harness or connector



WIRING DIAGRAM

E402276E20
1.083,1.917 1.542,2.115 0.458,0.198 10 false A73 1.083,2.073 2.375,2.583 1.292,0.51 10 false Vehicle Approaching Speaker Assembly 4.74,1.938 5.198,2.135 0.458,0.198 10 false G97 4.76,2.094 6.042,2.563 1.281,0.469 10 false Vehicle Approaching Speaker Controller 2.104,0.969 2.563,1.167 0.458,0.198 10 false 2 2.104,1.375 2.563,1.573 0.458,0.198 10 false 1 4.75,0.99 5.208,1.188 0.458,0.198 10 false 7 4.75,1.375 5.208,1.573 0.458,0.198 10 false 8 4.938,1.073 5.396,1.271 0.458,0.198 10 false SP+ 4.938,1.49 5.396,1.688 0.458,0.198 10 false SP-

PROCEDURE

1.INSPECT VEHICLE APPROACHING SPEAKER ASSEMBLY
a.

Remove the vehicle approaching speaker assembly.

Click hereVehicle Exterior>ACOUSTIC VEHICLE ALERTING SYSTEM>VEHICLE APPROACHING SPEAKER>REMOVAL


b.

Inspect the vehicle approaching speaker assembly.

Click hereVehicle Exterior>ACOUSTIC VEHICLE ALERTING SYSTEM>VEHICLE APPROACHING SPEAKER>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER ASSEMBLY - VEHICLE APPROACHING SPEAKER CONTROLLER)

NG

REPLACE VEHICLE APPROACHING SPEAKER ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER ASSEMBLY - VEHICLE APPROACHING SPEAKER CONTROLLER)
a.

Disconnect the G97 vehicle approaching speaker controller connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A73-2 - G97-7 (SP+) Always Below 1 Ω
A73-1 - G97-8 (SP-) Always Below 1 Ω
A73-2 or G97-7 (SP+) - Body ground Always 10 kΩ or higher
A73-1 or G97-8 (SP-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR