The ECM uses sensors mounted in front of and behind the three-way catalytic converter to monitor its efficiency.
The first sensor, the air fuel ratio sensor, sends pre-catalyst information to the ECM. The second sensor, the heated oxygen sensor, sends post-catalyst information to the ECM.
In order to detect any deterioration in the three-way catalytic converter, the ECM calculates the oxygen storage capacity of the three-way catalytic converter. This calculation is based on the voltage output of the heated oxygen sensor while performing active air fuel ratio control.
The oxygen storage capacity value is an indication of the oxygen storage capacity of the three-way catalytic converter. When the vehicle is being driven with a warm engine, active air fuel ratio control is performed for approximately 15 to 25 seconds. When it is performed, the ECM deliberately sets the air fuel ratio to lean or rich levels. If the cycle of the waveform for the heated oxygen sensor is long, the oxygen storage capacity is great. There is a direct correlation between the heated oxygen sensor and the oxygen storage capacity of the three-way catalytic converter.
The ECM uses the oxygen storage capacity value to determine the state of the three-way catalytic converter. If any deterioration has occurred, it illuminates the MIL and stores the DTC.
This system determines the deterioration of the entire catalyst system (including the front and rear catalysts), by using the oxygen storage capacity value of the front catalyst, that is more sensitive than the rear catalyst, as the representative value. Therefore, be sure to replace the front and rear catalysts together when catalyst replacement is necessary.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0420 | Oxygen storage capacity value smaller than standard value under active air fuel ratio control (2 trip detection logic). | ·
Gas leaks from exhaust system ·
Air fuel ratio sensor (sensor 1) ·
Heated oxygen sensor (sensor 2) ·
Front exhaust pipe assembly (TWC: Front and rear catalyst) ·
EGR valve assembly |
| *A | w/ Exhaust Heat Recirculation System | *B | w/o Exhaust Heat Recirculation System |
| *1 | Air Fuel Ratio Sensor (Sensor 1) | *2 | Heated Oxygen Sensor (Sensor 2) |
| *3 | Exhaust Manifold Sub-assembly | *4 | Front Exhaust Pipe Assembly |
| *5 | Tail Exhaust Pipe Assembly | *6 | TWC: Front Catalyst |
| *7 | TWC: Rear Catalyst | - | - |
When replacing the front exhaust pipe assembly (*4) in order to replace the three-way catalytic converter, it is not necessary to replace the heated oxygen sensor (*2).
| Required Sensors/Components (Main) | Air fuel ratio sensor
Heated oxygen sensor |
| Required Sensors/Components (Related) | Intake air temperature sensor
Mass air flow meter sub-assembly Crankshaft position sensor Engine coolant temperature sensor |
| Frequency of Operation | Once per driving cycle |
| Auxiliary battery voltage | 11 V or higher |
| Intake air temperature | -10°C (14°F) or higher |
| Engine coolant temperature | 75°C (167°F) or higher |
| Atmospheric pressure | 76 kPa(abs) [570 mmHg(abs)] or higher |
| Idling | Off |
| Engine speed | Less than 4000 rpm |
| Air fuel ratio sensor status | Activated |
| Fuel system status | Closed loop |
| Engine load | 10% or higher, and less than 70% |
| All of the following conditions (a), (b) and (c) are met | - |
| (a) Mass air flow rate | 2.5 gm/sec or more, and less than 50 gm/sec |
| (b) Front catalyst temperature (estimated) | 530°C (986°F) or higher, and less than 770°C (1418°F) |
| (c) Rear catalyst temperature (estimated) | 450°C (842°F) or higher, and less than 700°C (1292°F) |
Performing this confirmation driving pattern will activate the catalyst efficiency monitor. This is very useful for verifying the completion of a repair.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).
Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].
Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [B].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Drive the vehicle while keeping the engine load as constant as possible.
Turn the power switch off and wait for at least 30 seconds [C].
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).
Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [D].
Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [E].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Drive the vehicle while keeping the engine load as constant as possible.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [F].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0420.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A and no pending DTC is output, perform the following procedure.
Drive the vehicle at a speed 100 km/h (62 mph) for 10 minutes or more [G].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Drive the vehicle while keeping the engine load as constant as possible.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [H].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0420.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
Perform the operation with the engine speeds and time durations described below prior to checking the waveforms of the air fuel ratio and heated oxygen sensors. This is to activate the sensors sufficiently to obtain appropriate inspection results.
(a) Connect the GTS to the DLC3.
(b) Turn the power switch on (IG) and turn the GTS on.
(c) Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).
(d) Start the engine and warm it up with all the accessories switched off until the engine coolant temperature stabilizes [A].
(e) Run the engine at an engine speed of 2500 rpm for at least 3 minutes [B].
During charging control, the engine speed is set at idle. Therefore, the engine speed does not increase when depressing the accelerator pedal. In this case, perform step [B] after charging control has completed.
(f) While running the engine at 2500 rpm for 2 seconds and 1500 rpm for 2 seconds, check the waveforms of the air fuel ratio and heated oxygen sensors using the GTS [C].
If either of the voltage outputs of the air fuel ratio or heated oxygen sensor does not fluctuate, or there is noise in the waveform of either sensor, the sensor may be malfunctioning.
If the voltage outputs of both the sensors remain lean or rich, the air fuel ratio may be extremely lean or rich. In such cases, perform the Control the Injection Volume for A/F Sensor Active Test using the GTS.
If the three-way catalytic converter has deteriorated, the heated oxygen sensor (located behind the three-way catalytic converter) output voltage fluctuates up and down frequently, even under normal driving conditions (active air fuel ratio control is not performed).
If a malfunction cannot be found when troubleshooting DTC P0420, a lean or rich abnormality may be cause. Perform troubleshooting by following the inspection procedure for P0171 (System Too Lean) and P0172 (System Too Rich).
Sensor 1 refers to the sensor closest to the engine assembly.
Sensor 2 refers to the sensor farthest away from the engine assembly.
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P0420 is output | A |
| DTC P0420 and other DTCs are output | B |
If any DTCs other than P0420 are output, troubleshoot those DTCs first.
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).
Start the engine warm it up.
Run the engine at an engine speed of 2500 rpm for approximately 90 seconds.
During charging control, the engine speed is set at idle. Therefore, the engine speed does not increase when depressing the accelerator pedal. In this case, warm up the engine after charging control has completed.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and O2S B1S2.
Perform the Active Test operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).
Monitor the output voltages of the air fuel ratio sensor and heated oxygen sensor (AFS Voltage B1S1 and O2S B1S2) displayed on the GTS.
The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by -12.5% or increases the injection volume by 12.5%.
Each sensor reacts in accordance with increases and decreases in the fuel injection volume.
The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.
| GTS Display (Sensor) | Injection Volume | Status | Voltage |
|---|---|---|---|
| AFS Voltage B1S1
(Air fuel ratio) |
12.5% | Rich | Less than 3.1 V |
| AFS Voltage B1S1
(Air fuel ratio) |
-12.5% | Lean | Higher than 3.4 V |
| O2S B1S2
(Heated oxygen) |
12.5% | Rich | Higher than 0.55 V |
| O2S B1S2
(Heated oxygen) |
-12.5% | Lean | Less than 0.4 V |
| Status of AFS Voltage B1S1 | Status of O2S B1S2 | Air Fuel Ratio Condition and Air Fuel Ratio and Heated Oxygen Sensor Condition | Misfire | Suspected Trouble Area | Proceed to |
|---|---|---|---|---|---|
| Lean/Rich | Lean/Rich | Normal | - | ·
Tree-way catalytic converter ·
Gas leaks from exhaust system ·
EGR valve assembly |
A |
| Lean | Lean/Rich | Air fuel ratio sensor malfunction | - | Air fuel ratio sensor | B |
| Rich | Lean/Rich | Air fuel ratio sensor malfunction | - | Air fuel ratio sensor | |
| Lean/Rich | Lean | Heated oxygen sensor malfunction | - | ·
Heated oxygen sensor ·
Gas leaks from exhaust system |
C |
| Lean/Rich | Rich | Heated oxygen sensor malfunction | - | ·
Heated oxygen sensor ·
Gas leaks from exhaust system |
|
| Lean | Lean | Actual air fuel ratio lean | May occur | ·
Extremely lean actual air fuel ratio ·
Gas leaks from exhaust system ·
EGR valve assembly |
D |
| Rich | Rich | Actual air fuel ratio rich | - | ·
Extremely rich actual air fuel ratio ·
Gas leaks from exhaust system ·
EGR valve assembly |
Lean: During the Control the Injection Volume for A/F Sensor Active Test, the air fuel ratio sensor output voltage (AFS Voltage) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2S) is consistently less than 0.4 V.
Rich: During the Control the Injection Volume for A/F Sensor Active Test, the AFS Voltage is consistently less than 3.1 V, and the O2S is consistently higher than 0.55 V.
Lean/Rich: During the Control the Injection Volume for A/F Sensor Active Test, the output voltage of the air fuel ratio sensor or the heated oxygen sensor alternates correctly.
A
B
C
D
Check for exhaust gas leaks.
No gas leaks.
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
The A/C switch and all accessory switches should be off.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / All Data / MAP.
Check the MAP value in the Data List while performing the Active Test.
Do not leave the EGR valve open for 10 seconds or more during the Active Test.
Be sure to return the EGR valve to step 0 when the Active Test is completed.
Do not open the EGR valve 30 steps or more during the Active Test.
MAP change in response to EGR step position.
| - | EGR Step Position (Active Test) | |
|---|---|---|
| 0 Steps | 0 to 30 Steps | |
| MAP
(Data List) |
(EGR valve is fully closed) | MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed |
While performing the Active Test, if the increase in the value of MAP is small, the EGR valve assembly may be a malfunctioning.
Even if the EGR valve assembly is malfunctioning, rough idling or an increase in the value of MAP may occur while performing the Active Test. However, the amount that the value of MAP increases will be smaller than normal.
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Remove the EGR valve assembly (See page Engine / Hybrid System>2ZR-FXE (EMISSION CONTROL)>EGR VALVE>REMOVAL).
Check if the EGR valve is stuck open.
EGR valve is tightly closed.
OK
NG
When replacing the front exhaust pipe assembly in order to replace the three-way catalytic converter, it is not necessary to replace the heated oxygen sensor.
Confirm the replacement parts, referring to the illustration in the Catalyst Location.
Replace the front exhaust pipe assembly (TWC: Front and rear catalyst) (See page Engine / Hybrid System>2ZR-FXE (INTAKE / EXHAUST)>EXHAUST PIPE>COMPONENTS).
NEXT
Replace the air fuel ratio sensor (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL).
NEXT
Check for exhaust gas leaks.
No gas leaks.
OK
NG
Replace the heated oxygen sensor (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>HEATED OXYGEN SENSOR>REMOVAL).
NEXT
Check for exhaust gas leaks.
No gas leaks.
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
The A/C switch and all accessory switches should be off.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / All Data / MAP.
Check the MAP value in the Data List while performing the Active Test.
Do not leave the EGR valve open for 10 seconds or more during the Active Test.
Be sure to return the EGR valve to step 0 when the Active Test is completed.
Do not open the EGR valve 30 steps or more during the Active Test.
MAP change in response to EGR step position.
| - | EGR Step Position (Active Test) | |
|---|---|---|
| 0 Steps | 0 to 30 Steps | |
| MAP
(Data List) |
(EGR valve is fully closed) | MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed |
While performing the Active Test, if the increase in the value of MAP is small, the EGR valve assembly may be a malfunctioning.
Even if the EGR valve assembly is malfunctioning, rough idling or an increase in the value of MAP may occur while performing the Active Test. However, the amount that the value of MAP increases will be smaller than normal.
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Remove the EGR valve assembly (See page Engine / Hybrid System>2ZR-FXE (EMISSION CONTROL)>EGR VALVE>REMOVAL).
Check if the EGR valve is stuck open.
EGR valve is tightly closed.
OK
NG
Check the case of extremely rich or lean actual air fuel ratio, referring to the DTC P0171 Inspection Procedure (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>P0171).
NEXT
Repair or replace exhaust gas leak point.
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Clear the DTCs (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).
Start the engine.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P0420 is output | A |
| DTC is not output
(No pending DTCs output) |
B |
A
B
When replacing the front exhaust pipe assembly in order to replace the three-way catalytic converter, it is not necessary to replace the heated oxygen sensor.
Confirm the replacement parts, referring to the illustration in the Catalyst Location.
Replace the front exhaust pipe assembly (TWC: Front and rear catalyst) (See page Engine / Hybrid System>2ZR-FXE (INTAKE / EXHAUST)>EXHAUST PIPE>COMPONENTS).
NEXT