Home › Engine / Hybrid System › 2ZR-FXE (ENGINE CONTROL) › SFI SYSTEM › 2012.10–2014.11
RM2070E _51 Engine / Hybrid System _061905 2ZR-FXE ENGINE CONTROL _0301559 SFI SYSTEM C

2ZR-FXE ENGINE CONTROL  SFI SYSTEM  P0335  Crankshaft Position Sensor "A" Circuit  


DESCRIPTION

The crankshaft position sensor system consists of a No. 1 crankshaft position sensor plate and a pickup coil.

The sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of wound copper wire, an iron core and magnet. The sensor plate rotates and, as each tooth passes by the pickup coil, a pulse signal is created. The pickup coil generates 34 signals per engine revolution. Based on these signals, the ECM calculates the crankshaft position and engine speed. Using these calculations, the fuel injection time and ignition timing are controlled.

DTC No. DTC Detection Condition Trouble Area
P0335 Enter of the following conditions is met
(1 trip detection logic):
·

No crankshaft position sensor signal to ECM while engine running

·

Missing crankshaft position sensor signal despite camshaft position sensor signal inputs normal after engine cranked


·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

No. 1 crankshaft position sensor plate

·

ECM



A254145E19
2.969,0.99 3.323,1.188 0.354,0.198 10 false GND 0.063,0.063 0.604,0.24 0.542,0.177 10 false 5 V/DIV. 1.219,1.917 1.969,2.063 0.75,0.146 10 false 20 ms./DIV.

Reference: Inspection using an oscilloscope.

HINT:
·

The correct waveform is as shown.

·

Grounding failure of the shielded wire may cause noise in the waveform.



ECM Terminal Name Between NE+ and NE-
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine


MONITOR DESCRIPTION

If there is no signal from the crankshaft position sensor despite the engine rotating, the ECM interprets this as a malfunction of the sensor.

MONITOR STRATEGY

Required Sensors/Components (Main) Crankshaft position sensor
Required Sensors/Components (Related) Camshaft position sensor
Frequency of Operation Continuous

COMPONENT OPERATING RANGE

Crankshaft position sensor
·

Crankshaft position sensor output voltage fluctuates while crankshaft revolves

·

34 crankshaft position sensor signals per crankshaft revolution



CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for at least 30 seconds.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).

7.

Start the engine.

8.

Idle the engine for 20 seconds or more.

9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0335.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A255252E27
0.625,2.031 2.354,2.198 1.729,0.167 10 false Crankshaft Position Sensor 5.656,2.26 6.021,2.427 0.365,0.167 10 false ECM 0.625,1.865 0.927,2.031 0.302,0.167 10 false D27 5.083,0.708 5.333,0.896 0.25,0.188 10 false 74 5,1.542 5.302,1.729 0.302,0.188 10 false 120 5.656,2.104 6,2.281 0.344,0.177 10 false D28 5.344,0.708 5.635,0.854 0.292,0.146 10 false NE+ 5.344,1.542 5.635,1.688 0.292,0.146 10 false NE- 1.667,0.719 1.885,0.865 0.219,0.146 10 false NE 1.625,1.302 1.896,1.448 0.271,0.146 10 false NE- 2,0.719 2.104,0.885 0.104,0.167 10 false 1 2,1.521 2.115,1.688 0.115,0.167 10 false 2 3.229,1.729 3.802,1.917 0.573,0.188 10 false Shielded

CAUTION / NOTICE / HINT

HINT:
·

After performing the inspection procedure for the crankshaft position sensor, if DTC P0335 is output again, check the following items related to the camshaft position sensor.

-

Installation condition of the camshaft position sensor

-

Installation condition of the camshaft

-

Connection of the camshaft position sensor connector


·

If no problem is found through this diagnostic troubleshooting procedure, troubleshoot the engine mechanical system.

·

Check the engine speed. The engine speed can be checked using the GTS. To check, follow the operation below:

(a)

Connect the GTS to the DLC3.

(b)

Turn the power switch on (IG) and turn the GTS on.

(c)

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).

(d)

Start the engine.

(e)

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Engine Speed.


The engine speed may be indicated as zero despite the engine rotating normally. This is caused by a lack of NE signals from the crankshaft position sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed if the crankshaft position sensor output voltage is insufficient.


·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.



PROCEDURE

1.READ VALUE USING GTS (ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


e.

Start the engine.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Engine Speed.


g.

Read the values displayed on the GTS while the engine is running.

OK:

Correct values are displayed.


HINT:
·

To check the engine speed change, display the graph on the GTS.

·

If the engine does not start, check the engine speed while cranking.

·

If the engine speed indicated on the GTS remains at zero (0), there may be an open or short in the crankshaft position sensor circuit.





OK

NG

2.INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE)
2.INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE)

OK

3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Disconnect the crankshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D27-1 (NE) - D28-74 (NE+) Always Below 1 Ω
D27-2 (NE-) - D28-120 (NE-) Always Below 1 Ω
D27-1 (NE) or D28-74 (NE+) - Body ground Always 10 kΩ or higher
D27-2 (NE-) or D28-120 (NE-) - Body ground Always 10 kΩ or higher




OK

4.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)
A352601E02
1.656,1.563 2.5,1.802 0.844,0.24 10 false Clearance 0.5,1.698 0.906,1.938 0.406,0.24 10 false OK 2.656,1.813 3.427,2.177 0.771,0.365 10 true NG

a.

Check the crankshaft position sensor installation.

OK:

Crankshaft position sensor is installed correctly.




OK

5.INSPECT NO. 1 CRANKSHAFT POSITION SENSOR PLATE (TEETH OF SENSOR PLATE)

NG

SECURELY REINSTALL CRANKSHAFT POSITION SENSOR

5.INSPECT NO. 1 CRANKSHAFT POSITION SENSOR PLATE (TEETH OF SENSOR PLATE)
a.

Check the teeth of the No. 1 crankshaft position sensor plate (See page Engine / Hybrid System>2ZR-FXE (ENGINE MECHANICAL)>ENGINE UNIT>COMPONENTS).

OK:

Sensor plate does not have any cracks or deformation.




OK

6.REPLACE CRANKSHAFT POSITION SENSOR

NG

REPLACE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

6.REPLACE CRANKSHAFT POSITION SENSOR
a.


NEXT

7.CHECK WHETHER DTC OUTPUT RECURS
7.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.



e.

Turn the power switch off and wait for at least 30 seconds.


f.

Turn the power switch on (IG).


g.

Turn the GTS on.


h.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


i.

Start the engine.


j.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


k.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


l.

Read the DTCs.

Result
Result Proceed to
DTC is not output A
DTC P0335 is output B

HINT:

If the engine does not start, replace the ECM.




A

END

B