Home › Engine / Hybrid System › 2ZR-FXE (ENGINE CONTROL) › SFI SYSTEM › 2012.03–2014.11
RM2070E _51 Engine / Hybrid System _061905 2ZR-FXE ENGINE CONTROL _0301559 SFI SYSTEM C

2ZR-FXE ENGINE CONTROL  SFI SYSTEM  P0351  Ignition Coil "A" Primary / Secondary Circuit  P0352  Ignition Coil "B" Primary / Secondary Circuit  P0353  Ignition Coil "C" Primary / Secondary Circuit  P0354  Ignition Coil "D" Primary / Secondary Circuit  


DESCRIPTION

HINT:
·

These DTCs indicate malfunctions relating to the primary circuit.

·

If DTC P0351 is output, check the No. 1 ignition coil assembly circuit.

·

If DTC P0352 is output, check the No. 2 ignition coil assembly circuit.

·

If DTC P0353 is output, check the No. 3 ignition coil assembly circuit.

·

If DTC P0354 is output, check the No. 4 ignition coil assembly circuit.



A Direct Ignition System (DIS) is used on this vehicle.

The DIS is a 1-cylinder ignition system in which each cylinder is ignited by one ignition coil assembly and one spark plug is connected to the end of each secondary wiring. A powerful voltage, generated in the secondary wiring, is applied directly to each spark plug. The spark of the spark plugs passes from the center electrode to the ground electrodes.

The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches the current supplied to the primary coil on and off. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation (IGF) signal to the ECM for each cylinder ignition.

A259014E07
5.229,1.146 5.667,0.854 false 4.521,1.396 4.438,0.875 4.438,0.875 4.333,0.875 false 0.292,1.344 1.99,1.521 1.698,0.177 10 false Crankshaft Position Sensor 0.313,3.104 2.073,3.281 1.76,0.177 10 false Camshaft Position Sensor 0.188,4.219 2.125,5.01 1.938,0.792 10 false Other Sensors (Engine Coolant Temperature Sensor, Mass Air Flow Meter Sub-Assembly, Throttle Position Sensor, etc.) 2.75,0.573 3.073,0.75 0.323,0.177 10 false ECM 2.865,1.438 3.188,1.615 0.323,0.177 10 false IGT1 2.865,1.75 3.219,1.927 0.354,0.177 10 false IGF1 2.865,2.771 3.188,2.948 0.323,0.177 10 false IGT2 2.865,4.083 3.188,4.26 0.323,0.177 10 false IGT3 2.865,5.385 3.188,5.563 0.323,0.177 10 false IGT4 4.521,0.448 5.885,0.625 1.365,0.177 10 false from Auxiliary Battery 3.896,0.792 4.302,0.969 0.406,0.177 10 false Igniter 5.719,0.76 6.698,1.135 0.979,0.375 10 false No. 1 Ignition Coil Assembly 5.625,1.844 6.688,2.021 1.063,0.177 10 false No. 1 Spark Plug 4.25,2.625 5.188,2.99 0.938,0.365 10 false No. 2 Ignition Coil Assembly 4.25,3.958 5.188,4.354 0.938,0.396 10 false No. 3 Ignition Coil Assembly 4.25,5.26 5.177,5.615 0.927,0.354 10 false No. 4 Ignition Coil Assembly 5.625,3.063 6.688,3.24 1.063,0.177 10 false No. 2 Spark Plug 5.625,4.385 6.688,4.563 1.063,0.177 10 false No. 3 Spark Plug 5.625,5.698 6.688,5.875 1.063,0.177 10 false No. 4 Spark Plug

DTC No. DTC Detection Conditions Trouble Areas
P0351
P0352
P0353
P0354
No IGF signal to ECM while engine running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF or IGT circuit (1 to 4) between ignition coil assembly and ECM

·

No. 1 to No. 4 ignition coil assemblies

·

ECM



A122717E53
3.021,0.938 3.385,1.135 0.365,0.198 10 false GND 3.031,1.583 3.365,1.781 0.333,0.198 10 false GND 0.208,0.313 0.531,0.771 0.323,0.458 10 false CH1 (IGT) 0.188,1.302 0.573,1.698 0.385,0.396 10 false CH2 (IGF1) 0.031,0.031 0.573,0.208 0.542,0.177 10 false 2 V/DIV. 1.292,1.906 2.042,2.052 0.75,0.146 10 false 20 ms./DIV.

Reference: Inspection using an oscilloscope.


HINT:
·

The correct waveform is as shown.


·

While idling the engine, check the waveform between terminals IGT (1 to 4) and E1, and IGF1 and E1 of the ECM connector.



ECM Terminal Name CH1: Between IGT (1 to 4) and E1
CH2: Between IGF1 and E1
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Idling

MONITOR DESCRIPTION

A212405E08
1.782,1.645 2.181,1.818 0.399,0.173 10 ECM 2.956,1.3 3.225,1.485 0.269,0.185 10 IGT 2.949,1.726 3.226,1.886 0.278,0.160 10 IGF 4.153,1.509 4.594,1.655 0.441,0.145 10 Igniter 5.4,1.348 6.167,1.521 0.767,0.173 10 Ignition Coil 4.465,2.35 6.163,2.540 1.698,0.191 10 Ignition Coil Assembly 0.213,3.113 1.146,3.443 0.934,0.330 10 Ignition Signal (IGT) 1.642,3.541 2.131,3.731 0.489,0.191 10 Normal 1.383,3.947 2.150,4.138 0.767,0.191 10 Malfunction 0.262,3.907 1.146,4.768 0.884,0.862 10 Ignition Confirmation Signal (IGF) 3.631,4.507 4.482,4.684 0.850,0.177 10 Circuit Open 5.95,4.97 6.314,5.167 0.364,0.198 10 Time

If the ECM does not receive any IGF signals despite transmitting the IGT signal, it interprets this as a fault in the igniter and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) Igniter
Required Sensors/Components (Related) ECM
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for at least 30 seconds.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).

7.

Start the engine.

8.

Idle the engine for 10 seconds or more.

9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0351, P0352, P0353 or P0354.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A379318E02
0.083,0.813 0.5,1.125 0.417,0.313 10 false A 2.469,0.688 2.885,1 0.417,0.313 10 false 1 2.479,1.271 2.896,1.583 0.417,0.313 10 false 4 4.375,1.281 4.792,1.594 0.417,0.313 10 false 2 4.375,0.698 4.792,1.01 0.417,0.313 10 false 3 2.677,0.813 3.094,1.125 0.417,0.313 10 false +B 2.677,1.417 3.094,1.729 0.417,0.313 10 false GND 4.042,1.385 4.458,1.698 0.417,0.313 10 false IGF 3.99,0.802 4.406,1.115 0.417,0.313 10 false IGT1 5.219,0.698 5.635,1.01 0.417,0.313 10 false 108 5.24,2.438 5.656,2.75 0.417,0.313 10 false 107 5.208,4.219 5.625,4.531 0.417,0.313 10 false 106 2.615,1.729 3.031,2.042 0.417,0.313 10 false D23 2.615,1.896 4.542,2.281 1.927,0.385 10 false No. 1 Ignition Coil Assembly 2.635,3.479 3.052,3.792 0.417,0.313 10 false D22 2.615,5.229 3.031,5.542 0.417,0.313 10 false D21 2.646,7.01 3.063,7.323 0.417,0.313 10 false D20 5.76,8.146 6.177,8.458 0.417,0.313 10 false D28 6.125,8.146 6.542,8.458 0.417,0.313 10 false ECM 5.583,7.458 6,7.771 0.417,0.313 10 false E1 5.219,7.333 5.635,7.646 0.417,0.313 10 false 104 5.302,6.542 5.719,6.854 0.417,0.313 10 false 23 5.208,5.958 5.625,6.271 0.417,0.313 10 false 105 4.385,3.052 4.802,3.365 0.417,0.313 10 false 2 4.406,4.802 4.823,5.115 0.417,0.313 10 false 2 4.385,2.448 4.802,2.76 0.417,0.313 10 false 3 4.385,4.24 4.802,4.552 0.417,0.313 10 false 3 2.479,3.021 2.896,3.333 0.417,0.313 10 false 4 2.49,4.792 2.906,5.104 0.417,0.313 10 false 4 2.479,2.438 2.896,2.75 0.417,0.313 10 false 1 2.479,4.188 2.896,4.5 0.417,0.313 10 false 1 2.49,6.542 2.906,6.854 0.417,0.313 10 false 4 2.49,5.938 2.906,6.25 0.417,0.313 10 false 1 4.385,6.552 4.802,6.865 0.417,0.313 10 false 2 4.375,5.969 4.792,6.281 0.417,0.313 10 false 3 2.635,3.646 4.563,4.031 1.927,0.385 10 false No. 2 Ignition Coil Assembly 2.604,5.396 4.531,5.781 1.927,0.385 10 false No. 3 Ignition Coil Assembly 2.646,7.177 4.573,7.563 1.927,0.385 10 false No. 4 Ignition Coil Assembly 3.979,2.573 4.396,2.885 0.417,0.313 10 false IGT2 3.969,4.313 4.385,4.625 0.417,0.313 10 false IGT3 4.052,3.146 4.469,3.458 0.417,0.313 10 false IGF 4.042,4.875 4.458,5.188 0.417,0.313 10 false IGF 2.688,2.552 3.104,2.865 0.417,0.313 10 false +B 2.698,4.323 3.115,4.635 0.417,0.313 10 false +B 2.667,3.156 3.083,3.469 0.417,0.313 10 false GND 2.698,4.906 3.115,5.219 0.417,0.313 10 false GND 2.677,6.063 3.094,6.375 0.417,0.313 10 false +B 2.688,6.656 3.104,6.969 0.417,0.313 10 false GND 4.052,6.635 4.469,6.948 0.417,0.313 10 false IGF 3.979,6.063 4.396,6.375 0.417,0.313 10 false IGT4 5.573,6.552 5.99,6.865 0.417,0.313 10 false IGF1 5.563,5.885 5.979,6.198 0.417,0.313 10 false IGT4 5.573,4.167 5.99,4.479 0.417,0.313 10 false IGT3 5.583,2.406 6,2.719 0.417,0.313 10 false IGT2 5.552,0.646 5.969,0.958 0.417,0.313 10 false IGT1

A259016E01
0.696,3.901 1.299,4.235 0.603,0.334 10 Auxiliary Battery 3.248,3.871 4.542,4.185 1.294,0.313 10 Power Management Control ECU 0.588,1.819 1.192,2.000 0.603,0.181 10 P/I 1 3.78,3.372 4.164,3.553 0.384,0.181 10 IG2D 4.208,3.263 4.404,3.444 0.196,0.181 10 2 3.218,1.396 3.543,1.577 0.326,0.181 10 IG2 2.358,0.765 2.684,0.947 0.326,0.181 10 IG2 0.588,3.231 1.192,3.412 0.603,0.181 10 MAIN 7.01,0.606 7.150,0.787 0.141,0.181 10 A 2.949,3.871 3.225,4.052 0.276,0.181 10 A22 2.237,1.788 3.759,2.129 1.522,0.341 10 No. 2 Integration Relay 1.868,0.621 2.100,0.779 0.232,0.158 10 1C 3.97,1.064 4.202,1.222 0.232,0.158 10 1A 1.863,1.064 2.096,1.222 0.232,0.158 10 1A 3.97,0.616 4.202,0.774 0.232,0.158 10 1A 1.91,0.429 2.080,0.580 0.170,0.151 10 1 1.915,0.891 2.034,1.061 0.119,0.170 10 3 4.021,0.891 4.140,1.061 0.119,0.170 10 2 4.03,0.434 4.157,0.591 0.127,0.157 10 4

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGNITION COIL ASSEMBLY)
a.
U154230E03
1.313,2.49 0.792,3.021 false 2.167,2.49 2.635,3.01 false 0.271,0.198 0.458,0.406 0.188,0.208 10 false *a 0.635,3.042 0.844,3.219 0.208,0.177 10 false +B 2.563,3.031 2.927,3.188 0.365,0.156 10 false GND 0.135,1.979 0.427,2.167 0.292,0.188 10 false D23 0.625,1.99 0.906,2.177 0.281,0.188 10 false D22 0.146,2.26 0.417,2.417 0.271,0.156 10 false D21 0.625,2.26 0.906,2.417 0.281,0.156 10 false D20

Disconnect the ignition coil assembly connectors.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D23-1 (+B) - D23-4 (GND) Power switch on (IG) 11 to 14 V
D22-1 (+B) - D22-4 (GND) Power switch on (IG) 11 to 14 V
D21-1 (+B) - D21-4 (GND) Power switch on (IG) 11 to 14 V
D20-1 (+B) - D20-4 (GND) Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Ignition Coil Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION COIL ASSEMBLY - IG2 RELAY)

2.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)
a.

Disconnect the ignition coil assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D23-4 (GND) - Body ground Always Below 1 Ω
D22-4 (GND) - Body ground Always Below 1 Ω
D21-4 (GND) - Body ground Always Below 1 Ω
D20-4 (GND) - Body ground Always Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
a.

Disconnect the ignition coil assembly connectors.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D23-2 (IGF) - D28-23 (IGF1) Always Below 1 Ω
D22-2 (IGF) - D28-23 (IGF1) Always Below 1 Ω
D21-2 (IGF) - D28-23 (IGF1) Always Below 1 Ω
D20-2 (IGF) - D28-23 (IGF1) Always Below 1 Ω
D23-3 (IGT1) - D28-108 (IGT1) Always Below 1 Ω
D22-3 (IGT2) - D28-107 (IGT2) Always Below 1 Ω
D21-3 (IGT3) - D28-106 (IGT3) Always Below 1 Ω
D20-3 (IGT4) - D28-105 (IGT4) Always Below 1 Ω
D23-2 (IGF) or D28-23 (IGF1) - Body ground Always 10 kΩ or higher
D23-3 (IGT1) or D28-108 (IGT1) - Body ground Always 10 kΩ or higher
D22-3 (IGT2) or D28-107 (IGT2) - Body ground Always 10 kΩ or higher
D21-3 (IGT3) or D28-106 (IGT3) - Body ground Always 10 kΩ or higher
D20-3 (IGT4) or D28-105 (IGT4) - Body ground Always 10 kΩ or higher
D23-2 (IGF), D22-2 (IGF), D21-2 (IGF), D20-2 (IGF) or D28-23 (IGF1) - Body ground Always 10 kΩ or higher




OK

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353 OR P0354)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353 OR P0354)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.



e.

Shuffle arrangement of the ignition coil assemblies (among No. 1 to No. 4 cylinders).

NOTICE:

Do not shuffle the connectors.



f.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Read the DTCs.

Result
Result Proceed to
Same DTC output A
Different ignition coil DTC output B



A

B