Home › Engine / Hybrid System › 2ZR-FXE (ENGINE CONTROL) › SFI SYSTEM › from 2016.05
RM2070E _51 Engine / Hybrid System _061905 2ZR-FXE ENGINE CONTROL _0301559 SFI SYSTEM C

2ZR-FXE ENGINE CONTROL  SFI SYSTEM  P0443  Evaporative Emission Control System Purge Control Valve Circuit  


DESCRIPTION

To reduce hydrocarbon (HC) emissions, evaporated fuel from the fuel tank is routed through a charcoal canister to the intake manifold for combustion in the cylinders.

The ECM changes the duty signals to the purge VSV (Vacuum Switching Valve for Purge Control) so that the intake amount of hydrocarbon (HC) emissions is appropriate for the driving conditions (engine load, engine speed, vehicle speed, etc.) after the engine is warmed up.

DTC No. DTC Detection Condition Trouble Area
P0443 Both of the following conditions (a) and (b) are met (1 trip detection logic):
(a) The target control value and actual control value do not match for 10 seconds or more.
(b) The target control value and actual control value do not match for 80 times or more.
·

Open or short in purge VSV circuit

·

Purge VSV

·

ECM



CONFIRMATION DRIVING PATTERN

A179391E08
1.525,1.949 1.755,2.124 0.230,0.174 10 [A] 2.846,1.949 3.076,2.124 0.230,0.174 10 [B] 3.892,3.005 4.122,3.179 0.230,0.174 10 [C] 4.574,1.338 4.804,1.512 0.230,0.174 10 [D] 5.097,3.005 5.327,3.179 0.230,0.174 10 [E] 0.509,2.071 0.887,2.255 0.378,0.184 10 Idling 4.224,2.524 5.010,2.837 0.786,0.313 10 10 minutes or more 2.594,2.524 3.380,2.837 0.786,0.313 10 15 minutes or more 1.31,2.524 2.105,2.689 0.795,0.165 10 Warming up 1.332,1.069 2.905,1.392 1.573,0.323 10 Between 40 and 60 km/h 0.954,1.546 1.171,1.139 1.171,1.139 1.269,1.139 false 0.128,0.45 1.081,0.616 0.952,0.165 10 Vehicle Speed

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for at least 30 seconds.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).

7.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].

HINT:

The A/C switch and all accessory switches should be off.


8.

Idle the engine for 15 minutes or more [B].

HINT:

Check the EVAP (Purge) VSV item in the Data List. When the value of this item is between 5 and 95%, the judgment will be performed.


9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0443.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [D] and [E].



14.

Drive the vehicle at a constant speed between 40 and 60 km/h (25 and 37 mph) for 10 minutes or more [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


15.

Check the DTC judgment result again [E].


WIRING DIAGRAM

A256097E02
6.083,3.748 6.416,3.895 0.333,0.147 10 ECM 5.704,0.987 6.033,1.135 0.330,0.149 10 PRG 5.704,2.724 6.131,2.873 0.427,0.149 10 MREL 5.357,2.818 5.624,2.974 0.267,0.156 10 A57 5.445,2.64 5.545,2.796 0.100,0.156 10 6 5.357,1.071 5.631,1.227 0.274,0.156 10 D28 5.404,0.888 5.585,1.044 0.181,0.156 10 28 5.704,3.285 5.894,3.434 0.191,0.149 10 E1 5.357,3.285 5.631,3.441 0.274,0.156 10 D28 5.376,3.116 5.626,3.271 0.250,0.156 10 104 4.474,1.47 5.200,1.647 0.725,0.177 10 Purge VSV 4.474,1.302 4.828,1.458 0.354,0.156 10 D11 4.39,0.983 4.505,1.125 0.114,0.142 10 2 4.996,0.987 5.111,1.129 0.114,0.142 10 1 3.367,1.071 3.575,1.227 0.208,0.156 10 1B 1.424,1.596 1.632,1.752 0.208,0.156 10 1B 1.424,1.071 1.632,1.227 0.208,0.156 10 1C 1.464,0.888 1.597,1.046 0.133,0.158 10 1 2.372,1.833 3.014,1.970 0.642,0.137 10 EFI MAIN 1.731,1.21 2.355,1.360 0.625,0.150 10 EFI MAIN 0.505,2.2 0.888,2.344 0.383,0.144 10 MAIN 0.505,1.499 0.812,1.643 0.307,0.144 10 P/I 1 3.685,1.222 4.327,1.360 0.642,0.137 10 EFI NO. 2 1.464,1.424 1.581,1.580 0.117,0.156 10 3 3.367,1.596 3.575,1.752 0.208,0.156 10 1B 3.409,1.438 3.526,1.594 0.117,0.156 10 2 3.409,0.888 3.526,1.025 0.117,0.137 10 4 0.63,2.92 1.180,3.253 0.551,0.333 10 Auxiliary Battery 1.773,2.236 3.246,2.385 1.473,0.149 10 No. 2 Integration Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR EVAP CONTROL)
a.
A216013E04
1.542,1.063 1.208,1.979 false 1.208,1.979 1.083,1.979 false 2.719,1.229 3.063,1.625 false 3.063,1.625 3.167,1.625 false 3.188,1.531 3.365,1.719 0.177,0.188 10 false *2 0.865,1.854 1.042,2.042 0.177,0.188 10 true *1

Disconnect the hose (on the canister side) of the purge VSV.

Text in Illustration
*1 Purge VSV
*2 Hose (to Canister)


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


f.

Start the engine.


g.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for EVAP Control.


h.

Operate the purge VSV and check the air flow.

OK:
Activate the VSV for Evap Control Specified Condition
ON Air flows
OFF Air does not flow


Result
Result Proceed to
Abnormal A
Normal B

HINT:

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.




A

2.INSPECT PURGE VSV

B

2.INSPECT PURGE VSV

OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PURGE VSV)

NG

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PURGE VSV)
a.
U110413E03
0.271,0.208 0.458,0.396 0.188,0.188 10 false *a 0.656,2.156 0.969,2.333 0.313,0.177 10 false D11

Disconnect the purge VSV connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D11-2 - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Purge VSV)



OK

4.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI MAIN RELAY - PURGE VSV)

4.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)
a.

Disconnect the purge VSV connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D11-1 - D28-28 (PRG) Always Below 1 Ω
D11-1 or D28-28 (PRG) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR