Home › Engine / Hybrid System › 2ZR-FXE (ENGINE CONTROL) › SFI SYSTEM › 2012.03–2014.11
RM2070E _51 Engine / Hybrid System _061905 2ZR-FXE ENGINE CONTROL _0301559 SFI SYSTEM C

2ZR-FXE ENGINE CONTROL  SFI SYSTEM  P0560  System Voltage  


MONITOR DESCRIPTION

The auxiliary battery supplies electricity to the ECM even when the power switch is off. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the auxiliary battery voltage falls below a minimum level, the memory is cleared and the ECM determines that there is a malfunction in the power supply circuit. The next time the engine is started, the ECM illuminates the MIL and stores this DTC.

DTC No. DTC Detection Condition Trouble Area
P0560 An open in ECM back up power source circuit (1 trip detection logic).
·

Open in back up power source circuit

·

Auxiliary battery

·

Auxiliary battery terminals

·

ECM



HINT:

If DTC P0560 is stored, the ECM does not store other DTCs or the data stored in the ECM may be partly cleared.


MONITOR STRATEGY

Required Sensors/Components ECM
Frequency of Operation Continuous

TYPICAL MALFUNCTION THRESHOLDS

Both of the following conditions are met -
Stand-by RAM Initialized
ECM power source Less than 3.5 V

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for at least 30 seconds.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

Wait 5 seconds or more.

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0560.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A157717E35
0.927,1.885 1.49,2.375 0.563,0.49 10 false Auxiliary Battery 1.469,1.052 1.979,1.323 0.51,0.271 10 false MAIN 2.688,1.052 3.344,1.458 0.656,0.406 10 false P/I 1 3.813,1.052 4.656,1.365 0.844,0.313 10 false EFI MAIN 5.49,0.885 5.823,1.177 0.333,0.292 10 false A57 5.531,0.708 5.781,0.927 0.25,0.219 10 false 20 5.833,0.917 6.271,1.188 0.438,0.271 10 false BATT 5.49,1.469 5.823,1.729 0.333,0.26 10 false D28 5.49,1.302 5.802,1.521 0.313,0.219 10 false 104 5.833,1.49 6.156,1.74 0.323,0.25 10 false E1 6.031,2.375 6.531,2.604 0.5,0.229 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:
·

After turning power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


PROCEDURE

1.INSPECT AUXILIARY BATTERY
a.

Check that the auxiliary battery is not depleted (See page Power Source / Network>2ZR-FXE (BATTERY / CHARGING)>CHARGING SYSTEM>ON-VEHICLE INSPECTION).

OK:

Auxiliary battery is not depleted.




OK

2.CHECK AUXILIARY BATTERY TERMINAL

NG

REPLACE AUXILIARY BATTERY

2.CHECK AUXILIARY BATTERY TERMINAL
a.

Check that the auxiliary battery terminals are not loose or corroded.

OK:

Auxiliary battery terminals are not loose or corroded.




OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ECM)

NG

REPAIR OR REPLACE AUXILIARY BATTERY TERMINAL

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ECM)
a.
U190509E02
1.5,2.094 1.156,2.969 false 0.271,0.219 0.469,0.396 0.198,0.177 10 false *a 0.323,2.01 0.604,2.177 0.281,0.167 10 false A57 0.979,3 1.385,3.146 0.406,0.146 10 false BATT

Disconnect the ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A57-20 (BATT) - Body ground Always 11 to 16 V


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0560)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (AUXILIARY BATTERY - ECM)

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0560)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.



e.

Turn the power switch off and wait for at least 30 seconds.


f.

Turn the power switch on (IG).


g.

Turn the GTS on.


h.

Wait 5 seconds or more.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Read the DTCs.

Result
Result Proceed to
DTC P0560 is output A
DTC is not output B



A

B