Home › Engine / Hybrid System › 2ZR-FXE (ENGINE CONTROL) › SFI SYSTEM › 2012.03–2014.11
RM2070E _51 Engine / Hybrid System _061905 2ZR-FXE ENGINE CONTROL _0301559 SFI SYSTEM C

2ZR-FXE ENGINE CONTROL  SFI SYSTEM  P0010  Camshaft Position "A" Actuator Circuit (Bank 1)  


DESCRIPTION

The Variable Valve Timing (VVT) system adjusts the intake valve timing to improve driveability. The engine oil pressure turns the VVT controller to adjust the valve timing.

The camshaft timing oil control valve assembly is a solenoid valve and switches the engine oil line. The valve moves when the ECM applies 12 V to the solenoid. The ECM changes the energizing time to the solenoid (duty-cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.

A384173E12
2.542,4.625 2.813,4.271 2.813,4.271 3.521,4.271 false 3.74,5.115 3.344,5.115 3.344,5.115 3.156,4.813 false 0.135,0.104 1.188,0.49 1.052,0.385 10 false VVT System: 0.177,2.646 0.979,3.021 0.802,0.375 10 false Duty-cycle 1.604,3.74 4.427,4.094 2.823,0.354 10 false Camshaft Timing Oil Control Valve Assembly 0.323,4.313 1.719,4.698 1.396,0.385 10 false Engine Oil Pressure 3.573,4.198 6.635,4.51 3.063,0.313 10 false VVT Controller (Camshaft Timing Gear Assembly) 3.802,5.01 5.344,5.385 1.542,0.375 10 false Intake Camshaft 4.75,0.875 6.708,1.198 1.958,0.323 10 false Camshaft Position Sensor 4.688,1.406 6.573,1.729 1.885,0.323 10 false Crankshaft Position Sensor 4.51,1.906 6.823,2.219 2.313,0.313 10 false Mass Air Flow Meter Sub-assembly 4.823,2.406 6.563,2.792 1.74,0.385 10 false Throttle Position Sensor 4.49,2.917 6.802,3.188 2.313,0.271 10 false Engine Coolant Temperature Sensor 4.885,3.406 6.51,3.771 1.625,0.365 10 false Vehicle Speed Sensor 2.365,1.271 3.656,1.656 1.292,0.385 10 false Actual Valve Timing 2.354,2.021 3.74,2.396 1.385,0.375 10 false Target Valve Timing 2.646,2.729 3.448,3.104 0.802,0.375 10 false Correction 2.865,3.24 3.667,3.615 0.802,0.375 10 false ECM

DTC No. DTC Detection Condition Trouble Area
P0010 Open or short in camshaft timing oil control valve assembly circuit (1 trip detection logic).
·

Open or short in camshaft timing oil control valve assembly circuit

·

Camshaft timing oil control valve assembly

·

ECM



MONITOR DESCRIPTION

This DTC is designed to detect an open or short in the camshaft timing oil control valve assembly circuit. If the camshaft timing oil control valve duty-cycle is excessively high or low while the power switch is on (IG) or the engine is running, the ECM will illuminate the MIL and store the DTC.

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for at least 30 seconds.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

Wait 5 seconds or more.

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0010.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A255118E05
0.611,1.84 3.414,2.053 2.803,0.213 10 Camshaft Timing Oil Control Valve Assembly 0.247,1.84 0.542,1.985 0.295,0.145 10 D25 1.598,0.81 1.705,0.955 0.107,0.145 10 1 1.598,1.445 1.705,1.590 0.107,0.145 10 2 4.872,0.791 5.074,0.937 0.203,0.145 10 36 4.87,1.433 5.057,1.578 0.187,0.145 10 59 5.399,2.215 5.675,2.369 0.276,0.154 10 D28 5.143,1.435 5.550,1.580 0.407,0.145 10 OC1- 5.143,0.799 5.550,0.945 0.407,0.145 10 OC1+ 5.703,2.215 6.034,2.361 0.331,0.145 10 ECM 1.419,0.817 1.574,1.007 0.156,0.191 10 + 1.455,1.435 1.597,1.660 0.142,0.225 10 -

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ OUTPUT DTC (DTC P0010)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTC after recording the freeze frame data and DTC.


e.

Turn the power switch off and wait for 30 seconds.


f.

Turn the power switch on (IG).


g.

Turn the GTS on.


h.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


i.

Start the engine and allow the engine to idle.


j.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


k.

Read the DTCs.

Result
Result Proceed to
DTC P0010 is output A
DTC is not output B



A

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

B

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
a.

Inspect the camshaft timing oil control valve assembly (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>CAMSHAFT OIL CONTROL VALVE>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)
a.

Disconnect the camshaft timing oil control valve assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D25-1 (+) - D28-36 (OC1+) Always Below 1 Ω
D25-2 (-) - D28-59 (OC1-) Always Below 1 Ω
D25-1 (+) or D28-36 (OC1+) - Body ground Always 10 kΩ or higher
D25-2 (-) or D28-59 (OC1-) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR