Home › Engine / Hybrid System › 2ZR-FXE (ENGINE CONTROL) › SFI SYSTEM › 2012.03–2014.11
RM2070E _51 Engine / Hybrid System _061905 2ZR-FXE ENGINE CONTROL _0301559 SFI SYSTEM C

2ZR-FXE ENGINE CONTROL  SFI SYSTEM  P0403  Exhaust Gas Recirculation Control Circuit  


DESCRIPTION

Refer to DTC P0401 (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>P0401).

DTC No. DTC Detection Condition Trouble Area
P0403 Open or short in EGR valve circuit (1 trip detection logic).
·

Open or short in EGR valve assembly circuit

·

EGR valve assembly

·

ECM



MONITOR DESCRIPTION

This DTC is designed to detect an open or short in the EGR valve assembly circuit.

Example:

·

If the EGR1, EGR2, EGR3 or EGR4 terminal output voltage is excessively low, but the step motor is still operating, the ECM determines that there is a short in the EGR valve assembly circuit, and stores the DTC.

·

If the EGR1, EGR2, EGR3 or EGR4 terminal output voltage is excessively low, and the step motor is not operating, the ECM determines that there is an open in the EGR valve assembly circuit, and stores the DTC.


MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

A215251E08
2.329,2.896 2.916,3.225 0.586,0.330 10 Warming Up 3.406,2.896 4.119,3.085 0.714,0.190 10 10 minutes 2.025,2.046 2.223,2.234 0.198,0.188 10 [A] 2.532,1.777 2.757,1.966 0.225,0.189 10 [B] 3.781,0.69 3.993,0.877 0.211,0.187 10 [C] 4.44,3.293 4.678,3.463 0.238,0.171 10 [D] 0.737,0.817 1.790,0.991 1.053,0.173 10 20 km/h or more 1.435,1.902 1.808,2.074 0.373,0.172 10 Idling 0.886,2.204 1.799,2.576 0.913,0.371 10 Power Switch on (IG)

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for at least 30 seconds.

5.

Turn the power switch on (IG) and turn the GTS on [A].

6.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).

7.

Start the engine and warm it up [B].

8.

Drive the vehicle at 20 km/h (12 mph) or more for 10 minutes [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0403.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system has a normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




WIRING DIAGRAM

A259017E06
1.713,5.352 3.068,5.523 1.355,0.171 10 EGR Valve Assembly 0.709,4.759 1.344,5.102 0.635,0.343 10 Auxiliary Battery 0.631,3.894 1.043,4.047 0.413,0.154 10 MAIN 4.335,1.501 5.098,1.838 0.762,0.336 10 EFI NO. 2 2.691,1.315 3.417,1.468 0.725,0.154 10 EFI MAIN 5.842,1.064 6.278,1.217 0.436,0.154 10 MREL 5.488,1.064 5.785,1.217 0.297,0.154 10 A57 5.562,0.895 5.749,1.049 0.186,0.154 10 6 1.359,5.352 1.656,5.506 0.297,0.154 10 D10 5.534,2.885 5.755,3.038 0.221,0.154 10 45 5.534,3.277 5.755,3.431 0.221,0.154 10 44 5.534,3.669 5.755,3.823 0.221,0.154 10 43 5.534,4.062 5.755,4.215 0.221,0.154 10 42 3.068,2.955 3.212,3.108 0.144,0.154 10 4 3.068,3.347 3.212,3.501 0.144,0.154 10 3 3.068,3.739 3.212,3.893 0.144,0.154 10 6 3.068,4.888 3.212,5.042 0.144,0.154 10 5 3.068,4.524 3.212,4.678 0.144,0.154 10 2 3.068,4.132 3.212,4.285 0.144,0.154 10 1 5.842,3.06 6.248,3.214 0.405,0.154 10 EGR1 5.842,3.455 6.248,3.608 0.405,0.154 10 EGR2 5.842,3.84 6.248,3.993 0.405,0.154 10 EGR3 5.842,4.232 6.248,4.386 0.405,0.154 10 EGR4 2.592,2.955 3.007,3.108 0.415,0.154 10 EGR1 2.592,3.347 3.007,3.501 0.415,0.154 10 EGR2 2.592,3.739 3.007,3.893 0.415,0.154 10 EGR3 2.719,4.902 3.008,5.056 0.289,0.154 10 +B2 2.724,4.524 3.008,4.678 0.284,0.154 10 +B1 2.592,4.132 3.007,4.285 0.415,0.154 10 EGR4 5.486,4.232 5.759,4.386 0.273,0.154 10 D28 5.486,3.84 5.759,3.993 0.273,0.154 10 D28 5.486,3.455 5.759,3.608 0.273,0.154 10 D28 5.486,3.06 5.759,3.214 0.273,0.154 10 D28 1.993,0.824 2.626,0.978 0.634,0.154 10 EFI MAIN 6.096,4.789 6.432,4.943 0.336,0.154 10 ECM 0.649,2.866 1.062,3.020 0.413,0.154 10 P/I 1 1.697,0.689 1.933,0.869 0.236,0.180 10 1C 1.697,1.063 1.933,1.243 0.236,0.180 10 1B 3.511,1.063 3.747,1.243 0.236,0.180 10 1B 3.511,0.695 3.747,0.876 0.236,0.180 10 1B 1.747,0.53 1.903,0.671 0.156,0.141 10 1 1.747,0.899 1.867,1.099 0.120,0.200 10 3 3.572,0.899 3.692,1.099 0.120,0.200 10 2 3.559,0.525 3.664,0.686 0.105,0.161 10 4 1.861,1.541 3.452,1.877 1.591,0.336 10 No. 2 Integration Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


e.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

HINT:

The A/C switch and all accessory switches should be off.



f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / All Data / MAP.


g.

Check the MAP value in the Data List while performing the Active Test.

HINT:
·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.

·

Do not open the EGR valve 30 steps or more during the Active Test.



OK:

MAP change in response to EGR step position.


Standard:
- EGR Step Position (Active Test)
0 Steps 0 to 30 Steps
MAP
(Data List)
(EGR valve is fully closed) MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed


HINT:
·

While performing the Active Test, if the increase in the value of MAP is small, the EGR valve assembly may be a malfunctioning.

·

Even if the EGR valve assembly is malfunctioning, rough idling or an increase in the value of MAP may occur while performing the Active Test. However, the amount that the value of MAP increases will be smaller than normal.





OK

NG

2.INSPECT EGR VALVE ASSEMBLY
2.INSPECT EGR VALVE ASSEMBLY
a.


OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EGR VALVE ASSEMBLY)

NG

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EGR VALVE ASSEMBLY)
a.
U190521E02
1.823,2.021 2.625,1.26 false 2.594,2.938 1.833,2.375 false 0.365,1.896 0.698,2.073 0.333,0.177 10 false D10 0.229,0.188 0.448,0.365 0.219,0.177 10 false *a 2.646,2.885 2.969,3.063 0.323,0.177 10 false +B2 2.656,1.115 2.979,1.292 0.323,0.177 10 false +B1

Disconnect the EGR valve assembly connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D10-2 (+B1) - Body ground Power switch on (IG) 11 to 14 V
D10-5 (+B2) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to EGR Valve Assembly)



OK

4.CHECK HARNESS AND CONNECTOR (EGR VALVE ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (EGR VALVE ASSEMBLY - EFI MAIN RELAY)

4.CHECK HARNESS AND CONNECTOR (EGR VALVE ASSEMBLY - ECM)
a.

Disconnect the EGR valve assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D10-4 (EGR1) - D28-45 (EGR1) Always Below 1 Ω
D10-3 (EGR2) - D28-44 (EGR2) Always Below 1 Ω
D10-6 (EGR3) - D28-43 (EGR3) Always Below 1 Ω
D10-1 (EGR4) - D28-42 (EGR4) Always Below 1 Ω
D10-4 (EGR1) or D28-45 (EGR1) - Body ground Always 10 kΩ or higher
D10-3 (EGR2) or D28-44 (EGR2) - Body ground Always 10 kΩ or higher
D10-6 (EGR3) or D28-43 (EGR3) - Body ground Always 10 kΩ or higher
D10-1 (EGR4) or D28-42 (EGR4) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR