Home › Engine / Hybrid System › 2ZR-FXE (ENGINE CONTROL) › IGNITION SYSTEM › 2012.03–2014.11
RM2070E _51 Engine / Hybrid System _061905 2ZR-FXE ENGINE CONTROL _0301560 IGNITION SYSTEM G

2ZR-FXE ENGINE CONTROL  IGNITION SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 19100P 1. PERFORM SPARK TEST

a.

Check for DTCs (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

NOTICE:

If any DTC is present, perform troubleshooting in accordance with the procedure for that DTC.



b.

Remove the ignition coil assemblies and spark plugs (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>IGNITION COIL AND SPARK PLUG>REMOVAL).


c.
A216910

Disconnect the 4 fuel injector connectors.


d.

Set the vehicle to inspection mode (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).(Step 3)


e.
A216911

Install each spark plug into the ignition coil assembly, and then connect the ignition coil connector. (Step 4)


f.

Ground the spark plug. (Step 5)


g.

Check that spark occurs while the engine is being cranked. (Step 6)

HINT:

Repeat steps 3 to 6 for each spark plug and ignition coil assembly.


NOTICE:
·

Be sure to ground the spark plugs when checking them.

·

Do not crank the engine for more than 2 seconds.

Cranking will stop if the power switch is turned off.

·

If the ignition coil assembly has been struck or dropped, replace it.

·

If the spark plug has been struck or dropped, replace it.



HINT:

If spark does not occur for any cylinder, perform the following Inspect Ignition Coil and Spark Test procedure.



h.

Install the ignition coil assemblies and spark plugs (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>IGNITION COIL AND SPARK PLUG>INSTALLATION).


Hide 19500 2.INSPECT IGNITION COIL AND SPARK TEST

a.

Check that the ignition coil connector is securely connected.

Result:
Result Action
NG Connect securely
OK Go to next step



b.

Perform a spark test on each ignition coil assembly.

i.

Replace the ignition coil assembly with a known good one.


ii.

Set the vehicle to inspection mode (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


iii.

Perform the spark test again.

Result:
Result Action
NG Go to next step
OK Replace ignition coil assembly




c.

Perform a spark test.

i.

Replace the spark plug with a known good one.


ii.

Set the vehicle to inspection mode (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


iii.

Perform the spark test again.

Result:
Result Action
OK Replace the spark plug
NG Inspect the ignition system (See page (Click here))


NOTICE:
·

If the ignition coil assembly has been struck or dropped, replace it.

·

If the spark plug has been struck or dropped, replace it.





d.
A216910

Connect the 4 fuel injector connectors.


e.

Install the ignition coil assemblies and spark plugs (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>IGNITION COIL AND SPARK PLUG>INSTALLATION).


Hide 19100P 3.INSPECT SPARK PLUG

a.

Remove the ignition coil assemblies and spark plugs (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>IGNITION COIL AND SPARK PLUG>REMOVAL).


b.
I112891E02
0.667,2 1.073,2 false 0.479,1.896 0.792,2.094 0.313,0.198 10 false *a

Check the electrode.

Text in Illustration
*a Ground

i.

Using a megohmmeter, measure the resistance.

Standard Resistance:

10 MΩ or more


If the result is 10 MΩ or less, clean the plug and measure the resistance again.

HINT:

If a megohmmeter is not available, perform the following simple inspection instead.




c.
A126881

Alternative inspection method:

i.

Quickly accelerate the engine to approximately 2500 rpm 5 times.


ii.

Remove each spark plug.


iii.

Visually check the spark plug.

If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.



d.

Check the spark plug for any damage to its threads and insulator.

If there is any damage, replace the spark plug.

Recommended Spark Plug
Manufacturer Spark Plug Type
DENSO SC20HR11


e.
A126880E56
0.709,1.072 0.867,1.259 0.158,0.187 10 *a

Check the spark plug electrode gap.

Text in Illustration
*a Spark Plug Electrode Gap

Maximum Electrode Gap for Used Spark Plug:
Electrode Gap
1.3 mm (0.0512 in.)


If the gap is greater than the maximum, replace the spark plug.

Electrode Gap for New Spark Plug:
Electrode Gap
1.0 to 1.1 mm (0.0394 to 0.0433 in.)



f.
U110721

Clean the spark plugs.

If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner and then dry it.

Standard air pressure:

588 kPa (6.0 kgf/cm2, 85 psi)


Standard duration:

20 seconds or less.


HINT:

Only use the spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.



g.

Install the ignition coil assemblies and spark plugs (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>IGNITION COIL AND SPARK PLUG>INSTALLATION).