Home › Engine / Hybrid System › 2ZR-FXE (ENGINE CONTROL) › THROTTLE BODY › from 2014.11
RM2070E _51 Engine / Hybrid System _061905 2ZR-FXE ENGINE CONTROL _0301562 THROTTLE BODY A

2ZR-FXE ENGINE CONTROL  THROTTLE BODY  INSTALLATION  


PROCEDURE

Hide 22210 1.INSTALL THROTTLE BODY ASSEMBLY

a.

Type A:

i.
A212317E03
2.01,1.51 2.854,1.51 false 2.917,1.406 3.083,1.688 0.167,0.281 10 false *a

Install a new gasket onto the intake manifold.

HINT:

Orient the protrusion of the gasket as shown in the illustration.


Text in Illustration
*a Protrusion


ii.

Install the throttle body assembly with the 2 bolts and 2 nuts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


iii.

Connect the No. 1 water by-pass hose and No. 2 water by-pass hose.


iv.

Connect the connector.



b.

Type B:

i.
A288948E05
1.99,1.5 2.906,1.5 false 2.927,1.385 3.104,1.698 0.177,0.313 10 false *a

Install a new gasket onto the intake manifold.

HINT:

Orient the protrusion of the gasket as shown in the illustration.


Text in Illustration
*a Protrusion


ii.

Install the throttle body assembly with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


iii.

Connect the No. 1 water by-pass hose and No. 2 water by-pass hose.


iv.

Connect the connector.



Hide 2.INSTALL AIR CLEANER HOSE ASSEMBLY

a.

Install the air cleaner hose assembly and tighten the hose clamp.


b.

Connect the ventilation hose to the cylinder head cover sub-assembly.


Hide 3.INSTALL AIR CLEANER CASE

a.

Install the air cleaner case with the 3 bolts.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


b.

Connect the water hose to the 3 clamps.


c.

Install the air cleaner filter element sub-assembly.


Hide 17705 5.INSTALL AIR CLEANER CAP SUB-ASSEMBLY

a.

Install the air cleaner cap sub-assembly with the 2 clamps.


b.

Connect the air cleaner hose assembly and tighten the hose clamp.


c.

Connect the connector.


Hide 9.PERFORM INITIALIZATION

NOTICE:

Be sure to perform this procedure after reassembling the throttle body assembly, removing and reinstalling any throttle body component or replacing the ECM.


a.

Disconnect the cable from the negative (-) auxiliary battery terminal. Wait at least 60 seconds and reconnect the cable.


b.

Connect the GTS to the DLC3 and clear the DTCs (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).


c.

Set the vehicle to inspection mode (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


d.

Start the engine without operating the accelerator pedal and check that the MIL is not illuminated and that the idle speed is within the specified range when the air conditioning is switched off after the engine is warmed up.

Standard:
Condition Engine Idle Speed
A/C switched off 950 to 1050 rpm


NOTICE:
·

If the accelerator pedal is operated, perform the above steps again.

·

Be sure to perform this step with all accessories off.

·

Make sure that park (P) is selected.




e.

Perform a road test and confirm that there are no abnormalities.