Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2012.10–2016.05
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301573 HYBRID CONTROL SYSTEM J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  ECU Power Source Circuit  


DESCRIPTION

When the power switch is turned on (IG), current flows from the MREL terminal of the power management control ECU to the IGCT relay. This closes the IGCT relay contact points and supplies power to the +B1 and +B2 terminals of the power management control ECU.

WIRING DIAGRAM

A262625E01
0.439,2.553 0.535,2.709 0.096,0.156 10 2 1.901,2.814 1.996,2.998 0.096,0.184 10 2 2.751,2.814 2.846,2.998 0.096,0.184 10 1 2.751,2.38 2.846,2.564 0.096,0.184 10 5 5.493,1.866 5.589,2.050 0.096,0.184 10 5 5.771,2.071 6.043,2.214 0.272,0.143 10 +B1 5.771,2.477 6.043,2.620 0.272,0.143 10 +B2 5.771,2.916 6.214,3.059 0.443,0.143 10 MREL 5.038,5.21 7.137,5.402 2.099,0.192 10 Power Management Control ECU 5.771,3.406 6.043,3.549 0.272,0.143 10 E1 5.771,3.822 6.043,3.965 0.272,0.143 10 E12 5.493,2.277 5.589,2.461 0.096,0.184 10 2 5.493,2.73 5.589,2.914 0.096,0.184 10 6 5.493,3.197 5.589,3.381 0.096,0.184 10 6 5.493,3.631 5.589,3.815 0.096,0.184 10 4 3.498,2.366 3.594,2.550 0.096,0.184 10 1 3.904,2.366 4.000,2.550 0.096,0.184 10 2 1.901,2.38 1.996,2.564 0.096,0.184 10 3 0.663,2.763 1.032,2.919 0.369,0.156 10 IGCT 0.677,3.426 1.046,3.582 0.369,0.156 10 MAIN 0.789,4.229 1.820,4.385 1.031,0.156 10 Auxiliary Battery 2.19,3.309 2.545,3.465 0.355,0.156 10 IGCT 3.411,2.611 4.132,2.767 0.721,0.156 10 IGCT No. 2 0.439,2.926 0.535,3.082 0.096,0.156 10 1 5.771,4.275 6.043,4.418 0.272,0.143 10 E01 5.771,4.69 6.043,4.834 0.272,0.143 10 E02 5.493,4.08 5.589,4.263 0.096,0.184 10 5 5.493,4.5 5.589,4.684 0.096,0.184 10 5 3.411,2.069 4.150,2.225 0.739,0.156 10 IGCT No. 3 3.605,1.488 3.941,1.644 0.336,0.156 10 PCU 5.444,3.826 5.641,3.969 0.198,0.143 10 L6 5.458,4.276 5.646,4.419 0.188,0.143 10 L5 5.453,3.398 5.632,3.541 0.179,0.143 10 L5 5.453,4.711 5.632,4.854 0.179,0.143 10 L6 5.406,2.064 5.678,2.207 0.272,0.143 10 A22 5.406,2.926 5.678,3.069 0.272,0.143 10 A22 5.406,2.476 5.678,2.619 0.272,0.143 10 A21 4.896,0.956 6.746,1.291 1.849,0.336 10 to Transmission Control ECU Assembly 4.896,0.498 6.242,0.690 1.346,0.192 10 to Battery Smart Unit 4.896,0.064 7.159,0.256 2.262,0.192 10 to Inverter with Converter Assembly

PROCEDURE

1.CHECK POWER MANAGEMENT CONTROL ECU (+B1, +B2 VOLTAGE)
a.

Turn the power switch on (IG).


b.
U190670E03
0.667,2.667 0.927,1.719 false 1.521,2.677 1.323,1.719 false 0.688,0.99 0.958,1.156 0.271,0.167 10 false A21 1.281,1 1.552,1.167 0.271,0.167 10 false A22 1.417,2.688 1.74,2.885 0.323,0.198 10 false +B1 0.5,2.698 0.792,2.875 0.292,0.177 10 false +B2 0.188,0.125 0.365,0.302 0.177,0.177 10 false *a

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A22-5 (+B1) - Body ground Power switch on (IG) 11 to 14 V
A21-2 (+B2) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Component with harness connected
(Power Management Control ECU)


c.

Turn the power switch off.



OK

2.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)

NG

3.CHECK POWER MANAGEMENT CONTROL ECU (MREL VOLTAGE)
2.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)
a.

Disconnect the L5 and L6 power management control ECU connectors.


b.
U154442E03
1.781,2.115 1.479,2.896 false 1.854,2.115 1.927,2.906 false 2.708,2.115 2.531,2.906 false 2.781,2.104 2.958,2.885 false 1.948,1.458 2.125,1.625 0.177,0.167 10 false L5 2.708,1.458 2.885,1.625 0.177,0.167 10 false L6 1.385,2.896 1.604,3.063 0.219,0.167 10 false E1 2.396,2.896 2.688,3.063 0.292,0.167 10 false E02 2.854,2.896 3.146,3.063 0.292,0.167 10 false E12 1.802,2.896 2.083,3.063 0.281,0.167 10 false E01 0.188,0.188 0.406,0.354 0.219,0.167 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L5-5 (E01) - Body ground Always Below 1 Ω
L5-6 (E1) - Body ground Always Below 1 Ω
L6-4 (E12) - Body ground Always Below 1 Ω
L6-5 (E02) - Body ground Always Below 1 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)


c.

Reconnect the L5 and L6 power management control ECU connectors.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK POWER MANAGEMENT CONTROL ECU (MREL VOLTAGE)
a.

Turn the power switch on (IG).


b.
U154428E03
1.25,1.708 1.083,2.448 false 0.271,0.25 0.438,0.406 0.167,0.156 10 false *a 0.854,2.469 1.26,2.625 0.406,0.156 10 false MREL 1.281,0.99 1.552,1.156 0.271,0.167 10 false A22

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A22-6 (MREL) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Component with harness connected
(Power Management Control ECU)


c.

Turn the power switch off.



OK

4.CHECK FUSE (IGCT NO. 2)

NG

4.CHECK FUSE (IGCT NO. 2)
a.

Remove the IGCT NO. 2 fuse from the engine room relay block and junction block assembly.


b.
A270231E05
2.281,1.854 2.927,2.125 false 0.177,0.146 0.458,0.302 0.281,0.156 10 false *1 2.958,2.073 3.146,2.229 0.188,0.156 10 false *2

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IGCT NO. 2 fuse terminals Always Below 1 Ω


Text in Illustration
*1 Engine Room Relay Block and Junction Block Assembly
*2 IGCT NO. 2 Fuse


c.

Install the IGCT NO. 2 fuse.



OK

5.CHECK FUSE (IGCT)

NG

11.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY)
5.CHECK FUSE (IGCT)
a.
A270233E05
1.833,1.49 2.844,1.771 false 0.177,0.083 0.5,0.302 0.323,0.219 10 false *1 2.875,1.729 3.198,1.948 0.323,0.219 10 false *2

Remove the IGCT fuse from the engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IGCT fuse terminals Always Below 1 Ω


Text in Illustration
*1 Engine Room Relay Block and Junction Block Assembly
*2 IGCT Fuse


c.

Install the IGCT fuse.



OK

6.INSPECT RELAY (IGCT)

NG

12.CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY (IGCT FUSE - IGCT NO. 2 FUSE))
6.INSPECT RELAY (IGCT)
a.

Remove the IGCT relay from the engine room relay block and junction block assembly.


b.
A253297E01
0.165,0.068 0.398,0.266 0.232,0.198 10 *1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage is not applied between terminals 1 and 2 10 kΩ or higher
Auxiliary battery voltage is applied between terminals 1 and 2 Below 1 Ω


Text in Illustration
*1 IGCT Relay


c.

Install the IGCT relay.



OK

7.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY)

NG

REPLACE RELAY (IGCT)

7.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY)
a.

Remove the IGCT relay from the engine room relay block and junction block assembly.


b.

Disconnect the A21 and A22 power management control ECU connectors.


c.

Measure the resistance according to the value(s) in the table below.

U190723E02
1.458,1.542 1.635,1.938 false 1.823,1.542 2.125,1.948 false 0.688,0.042 0.844,0.208 0.156,0.167 10 false *a 6.24,1.802 6.396,1.969 0.156,0.167 10 false *2 4.365,0.042 4.521,0.208 0.156,0.167 10 false *1 1.531,1.938 1.802,2.083 0.271,0.146 10 false +B2 2.063,1.927 2.333,2.073 0.271,0.146 10 false +B1 1.813,2.167 2.083,2.333 0.271,0.167 10 false A22 1.219,2.167 1.49,2.333 0.271,0.167 10 false A21

Text in Illustration
*1 Engine Room Relay Block and Junction Block Assembly *2 IGCT relay
*a Rear view of wire harness connector
(to Power Management Control ECU)
- -

Standard Resistance:
Tester Connection Condition Specified Condition
A22-5 (+B1) - 5 (IGCT relay) Always Below 1 Ω
A21-2 (+B2) - 5 (IGCT relay) Always Below 1 Ω



d.

Install the IGCT relay.


e.

Reconnect the A21 and A22 power management control ECU connectors.



OK

8.CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY (IGCT RELAY - IGCT FUSE))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY (IGCT RELAY - IGCT FUSE))
a.
A270938E05
1.865,1.521 2.927,1.917 false 0.24,0.125 0.479,0.302 0.24,0.177 10 false *1 2.969,1.885 3.208,2.063 0.24,0.177 10 false *2

Remove the IGCT fuse from the engine room relay block and junction block assembly.

Text in Illustration
*1 Engine Room Relay Block and Junction Block Assembly
*2 IGCT Fuse


b.

Remove the IGCT relay from the engine room relay block and junction block assembly.


c.
A270939E03
0.137,0.068 0.302,0.224 0.165,0.156 10 *1 2.526,1.024 2.691,1.180 0.165,0.156 10 *2 2.56,2.386 2.725,2.542 0.165,0.156 10 *3

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (IGCT relay) - 2 (IGCT fuse) Always Below 1 Ω


Text in Illustration
*1 Engine Room Relay Block and Junction Block Assembly
*2 IGCT Fuse
*3 IGCT Relay


d.

Install the IGCT fuse.


e.

Install the IGCT relay.



OK

9.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY)
a.

Remove the IGCT relay from the engine room relay block and junction block assembly.


b.

Disconnect the A22 power management control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

U190725E02
0.52,0.226 0.690,0.377 0.170,0.151 10 *a 4.069,0.198 4.239,0.350 0.170,0.151 10 *1 6.153,1.931 6.323,2.082 0.170,0.151 10 *2 1.358,1.986 1.765,2.137 0.408,0.151 10 MREL 1.69,1.416 1.567,1.974 false 1.159,1.41 1.433,1.573 0.274,0.163 10 A22

Text in Illustration
*1 Engine Room Relay Block and Junction Block Assembly *2 IGCT Relay
*a Rear view of wire harness connector
(to Power Management Control ECU)
- -

Standard Resistance:
Tester Connection Condition Specified Condition
A22-6 (MREL) - 1 (IGCT relay) Always Below 1 Ω
A22-6 (MREL) or 1 (IGCT relay) - Body ground and other terminals Always 10 kΩ or higher



d.

Install the IGCT relay.


e.

Reconnect the A22 power management control ECU connectors.



OK

10.CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY - BODY GROUND)
a.

Remove the IGCT relay from the engine room relay block and junction block assembly.


b.
A270941E02
0.138,0.113 0.308,0.264 0.170,0.151 10 *1 2.532,2.398 2.701,2.549 0.170,0.151 10 *2

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (IGCT relay) - Body ground Always Below 1 Ω


Text in Illustration
*1 Engine Room Relay Block and Junction Block Assembly
*2 IGCT Relay


c.

Install the IGCT relay.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A59 inverter with converter assembly connector.


c.

Disconnect the A23 transmission control ECU assembly connector.


d.

Remove the No. 1 hybrid vehicle battery carrier bracket sub-assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL).


e.

Disconnect the L144 battery smart unit connector.


f.
A270942E05
2.302,1.875 2.969,2.188 false 0.24,0.031 0.521,0.219 0.281,0.188 10 false *1 3.01,2.167 3.292,2.354 0.281,0.188 10 false *2

Remove the IGCT No. 2 fuse from the engine room relay block and junction block assembly.

Text in Illustration
*1 Engine Room Relay Block and Junction Block Assembly
*2 IGCT No. 2 Fuse


g.

Disconnect the A21 and A22 power management control ECU connectors.


h.

Measure the resistance according to the value(s) in the table below.

U190726E02
1.448,1.542 1.573,1.948 false 1.833,1.542 2.094,1.948 false 0.688,0.052 0.844,0.219 0.156,0.167 10 false *a 6.24,1.031 6.396,1.198 0.156,0.167 10 false *2 4.406,0.125 4.563,0.292 0.156,0.167 10 false *1 1.469,1.948 1.74,2.094 0.271,0.146 10 false +B2 2.042,1.927 2.313,2.073 0.271,0.146 10 false +B1 1.823,2.167 2.094,2.333 0.271,0.167 10 false A22 1.219,2.167 1.49,2.333 0.271,0.167 10 false A21

Text in Illustration
*1 Engine Room Relay Block and Junction Block Assembly *2 IGCT No. 2 Fuse
*a Rear view of wire harness connector
(to Power Management Control ECU)
- -

Standard Resistance:
Tester Connection Condition Specified Condition
A22-5 (+B1) or 2 (IGCT No. 2 fuse) - Body ground and other terminals Always 10 kΩ or higher
A21-2 (+B2) or 2 (IGCT No. 2 fuse) - Body ground and other terminals Always 10 kΩ or higher



i.

Install the IGCT No. 2 fuse.


j.

Reconnect the A21 and A22 power management control ECU connectors.


k.

Reconnect the L144 battery smart unit connector.


l.

Install the No. 1 hybrid vehicle battery carrier bracket sub-assembly.


m.

Reconnect the A23 transmission control ECU assembly connector.


n.

Reconnect the A59 inverter with converter assembly connector.



OK

REPLACE FUSE (IGCT NO. 2)

NG

13.REPAIR OR REPLACE HARNESS OR CONNECTOR
12.CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY (IGCT FUSE - IGCT NO. 2 FUSE))
a.
A270944E04
2.302,0.948 2.948,0.719 false 1.865,1.51 2.969,1.375 false 2.292,1.875 2.948,2.031 false 2.292,1.958 2.938,2.302 false 0.26,0.146 0.417,0.292 0.156,0.146 10 false *1 2.979,2.229 3.135,2.375 0.156,0.146 10 false *5 2.979,1.958 3.135,2.104 0.156,0.146 10 false *4 2.979,0.604 3.135,0.75 0.156,0.146 10 false *3 2.979,1.281 3.135,1.427 0.156,0.146 10 false *2

Remove the IGCT fuse, IGCT No. 2 fuse, IGCT No. 3 fuse and PCU fuse from the engine room relay block and junction block assembly.

Text in Illustration
*1 Engine Room Relay Block and Junction Block Assembly
*2 IGCT Fuse
*3 IGCT No. 3 fuse
*4 IGCT No. 2 fuse
*5 PCU Fuse


b.

Remove the IGCT relay from the engine room relay block and junction block assembly.


c.
A270939E04
0.137,0.068 0.302,0.224 0.165,0.156 10 *1 2.526,1.024 2.691,1.180 0.165,0.156 10 *2 2.56,2.386 2.725,2.542 0.165,0.156 10 *3

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (IGCT relay) or 2 (IGCT fuse) - Body ground and other terminals Always 10 kΩ or higher


Text in Illustration
*1 Engine Room Relay Block and Junction Block Assembly
*2 IGCT Fuse
*3 IGCT Relay


d.
A270945E02
0.095,0.067 0.250,0.214 0.155,0.147 10 *1 2.537,2.38 2.691,2.527 0.155,0.147 10 *3 2.529,1.426 2.684,1.573 0.155,0.147 10 *2

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (IGCT relay) or 1 (IGCT No. 2 fuse) - Body ground and other terminals Always 10 kΩ or higher


Text in Illustration
*1 Engine Room Relay Block and Junction Block Assembly
*2 IGCT No. 2 Fuse
*3 IGCT Relay


e.

Install the IGCT fuse, IGCT No. 2 fuse, IGCT No. 3 fuse and PCU fuse.


f.

Install the IGCT relay.



OK

REPLACE FUSE (IGCT)

NG

14.REPAIR OR REPLACE HARNESS OR CONNECTOR
13.REPAIR OR REPLACE HARNESS OR CONNECTOR

NEXT

REPLACE FUSE (IGCT NO. 2)

14.REPAIR OR REPLACE HARNESS OR CONNECTOR

NEXT

REPLACE FUSE (IGCT)