Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HV BATTERY › 2012.03–2014.11
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301578 HV BATTERY A

HYBRID / BATTERY CONTROL  HV BATTERY  REMOVAL  


PROCEDURE

Hide 2. READ VALUE USING GTS

a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Temp of Batt TB 0 to 5.


d.

Read the Data List.

NOTICE:

If any of the temperatures listed in "Temp of Batt TB 0 to 5" are 50°C or more, leave the vehicle until the temperature drops to less than 50°C.



Hide 3. READ OUTPUT DTC

a.

Check for DTCs (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>DTC CHECK / CLEAR).

NOTICE:

Check for DTCs and confirm that P0AA6 (Hybrid Battery Voltage System Isolation Fault) is not output before removing or installing internal battery components. If this DTC is output, perform troubleshooting for this DTC first.



Hide 8.REMOVE FRONT SEAT ASSEMBLY RH

Hide 58534H 9.REMOVE CENTER FLOOR CARPET COVER LH

Hide 58533F 10.REMOVE CENTER FLOOR CARPET COVER RH

Hide 58804A 11.REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY

Hide 58817A 12.REMOVE FRONT NO. 2 CONSOLE BOX INSERT

Hide G920Q 14.REMOVE NO. 1 HYBRID BATTERY SHIELD SUB-ASSEMBLY

CAUTION:

Wear insulated gloves.


NOTICE:
·

When handling the HV battery, disconnect the high voltage connector of the battery smart unit to prevent the hybrid battery cell voltage from dropping.

·

Insulate the removed connectors with insulating tape.



a.
A251490

Disconnect the 3 clamps.


b.
A251491

Remove the 4 bolts and No. 1 hybrid battery shield sub-assembly.


c.
A251648

Disconnect the 4 connectors from the battery smart unit.

NOTICE:

Insulate the removed connectors with insulating tape.



Hide 82164 15.DISCONNECT FRAME WIRE

CAUTION:

Wear insulated gloves.


NOTICE:

Insulate the removed terminals with insulating tape.


a.
A251492

Using an insulated tool, remove the 3 nuts and disconnect the frame wire from the hybrid battery junction block assembly.


b.
A251483E01
0.681,2.587 0.935,2.915 0.254,0.327 10 *a

Install the frame wire as shown in the illustration.

Text in Illustration
*a Front of Vehicle


Hide G92F1 16.REMOVE NO. 1 HYBRID BATTERY EXHAUST DUCT

a.
A251494

Remove the 2 clips and No. 1 hybrid battery exhaust duct.


Hide G92D4 17.REMOVE NO. 4 HYBRID BATTERY INTAKE DUCT

a.
A251495

Remove the 2 clips and No. 4 hybrid battery intake duct.


Hide G9510 18.REMOVE HV BATTERY

CAUTION:

Wear insulated gloves.


NOTICE:
·

Insulate the removed connectors and terminals with insulating tape.

·

Since the HV battery is very heavy, 2 people are needed to remove the HV battery.

·

Use cardboard or other similar material to protect the HV battery and vehicle body from damage.

·

When moving the hybrid battery, make sure to use an engine lifter.



a.
A251493

Disconnect the 2 connectors.


b.

Disconnect the floor carpet from the HV battery.


c.

Remove the 6 bolts.

A251496


d.
A251497E01
0.796,1.818 1.009,1.985 0.213,0.167 10 *1 2.645,1.744 2.858,1.911 0.213,0.167 10 *1 1.135,1.657 0.964,1.818 false 2.614,1.478 2.734,1.729 false

Remove the HV battery.

HINT:

Be sure to place the HV battery on the attachment to prevent the guide pins from being damaged.


Text in Illustration
*1 Guide Pin


Hide G92N2 19.REMOVE NO. 2 HYBRID VEHICLE BATTERY COVER PANEL LH

CAUTION:

Wear insulated gloves.


NOTICE:

Insulate the removed connectors with insulating tape.


a.
A254770

Disconnect the connector.


b.
A251606

Remove the 4 bolts and No. 2 hybrid vehicle battery LH cover panel.


Hide G920R 21.REMOVE NO. 2 HYBRID BATTERY SHIELD SUB-ASSEMBLY

CAUTION:

Wear insulated gloves.


NOTICE:

Insulate the removed connectors with insulating tape.


a.
A251484

Disconnect the connector and clamp.


b.
A251485

Disconnect the clamp.


c.
A251486

Disconnect the connector.


d.

Remove the bolt and electric vehicle battery plug assembly as shown in the illustration.


e.
A251607

Remove the 4 bolts and No. 2 hybrid battery shield sub-assembly.


Hide G92Z0 22.REMOVE HYBRID BATTERY JUNCTION BLOCK ASSEMBLY

Hide G92X2 23.REMOVE NO. 2 HYBRID BATTERY PACK WIRE

CAUTION:

Wear insulated gloves.


a.
A249895

Disconnect the 2 clamps and remove the No. 2 hybrid battery pack wire.


Hide 24.PERFORM HV BATTERY RECOVERY INSPECTION

a.

Before returning the HV battery, make sure to perform a recovery inspection (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>RECOVERY INSPECTION)