Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2016.05
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301573 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0560-117  System Voltage  


DESCRIPTION

Regular battery power is supplied to the BATT terminal of the hybrid control ECU in order to store DTCs and freeze frame data. Even if the power switch is turned off, back-up power is supplied.


DTC No. INF Code DTC Detection Condition Trouble Area
P0560 117 Malfunction in the hybrid vehicle control ECU assembly back-up power source circuit
(1 trip detection logic)
·

Wire harness or connector

·

Hybrid vehicle control ECU

·

Fuse



WIRING DIAGRAM

A384172E02
0.906,2.115 1.5,2.625 0.594,0.51 10 false Auxiliary Battery 1.49,1.302 2.104,1.5 0.615,0.198 10 false MAIN 3.76,1.302 4.219,1.5 0.458,0.198 10 false AM2 1.458,1 1.615,1.198 0.156,0.198 10 false 1 1.76,1.01 1.917,1.208 0.156,0.198 10 false 2 3.698,1.021 3.854,1.219 0.156,0.198 10 false 1 4,1.021 4.156,1.219 0.156,0.198 10 false 2 5.177,2.813 7.031,3.26 1.854,0.448 10 false Hybrid Vehicle Control ECU 5.323,1.125 5.938,1.323 0.615,0.198 10 false L6 5.333,1.729 5.948,1.927 0.615,0.198 10 false L5 5.354,0.938 5.51,1.135 0.156,0.198 10 false 3 5.354,1.531 5.51,1.729 0.156,0.198 10 false 6 5.656,1.135 6.271,1.333 0.615,0.198 10 false BATT 5.667,1.74 5.979,1.938 0.313,0.198 10 false E1

CAUTION / NOTICE / HINT

HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the power switch on (IG) and wait for 5 seconds or more.



PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

OK

2.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - AM2 FUSE)

NG

CONNECT SECURELY

2.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - AM2 FUSE)
a.

Turn the power switch off.


b.
U190786E02
1.813,1.719 1.656,2.479 true 2.698,1.719 2.958,2.51 true 1.563,2.49 1.813,2.708 0.25,0.219 10 false E1 2.813,2.521 3.25,2.698 0.438,0.177 10 false BATT 1.896,1.083 2.292,1.271 0.396,0.188 10 false L5 2.521,1.073 2.917,1.26 0.396,0.188 10 false L6 0.115,0.083 0.51,0.271 0.396,0.188 10 false *a

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L6-3 (BATT) - L5-6 (E1) Power switch off 11 to 14 V


Text in Illustration
*a Component without harness connected
(Hybrid Vehicle Control ECU)



OK

NG

3.CHECK FUSE (AM2)
3.CHECK FUSE (AM2)
a.
A380881E03
1.771,1.26 2.875,1.625 true 0.094,0.073 0.26,0.302 0.167,0.229 10 false *1 2.917,1.552 3.083,1.781 0.167,0.229 10 false *2

Remove the AM2 fuse from the engine room relay block and junction block assembly.

Text in Illustration
*1 Engine Room Relay Block and Junction Block Assembly
*2 AM2 Fuse


b.

Check if there is an open circuit in the AM2 fuse in the engine room relay block and junction block assembly.

OK:

There is no open circuit in the AM2 fuse.



c.

Install the AM2 fuse.



OK

4.CHECK HARNESS AND CONNECTOR (AM2 FUSE - BATTERY TERMINAL)

NG

REPLACE FUSE (AM2)

4.CHECK HARNESS AND CONNECTOR (AM2 FUSE - BATTERY TERMINAL)
a.
A380882E02
0.094,0.094 0.448,0.365 0.354,0.271 10 false *1 2.313,0.979 2.667,1.25 0.354,0.271 10 false *2

Remove the AM2 fuse from the engine room relay block and junction block assembly.

Text in Illustration
*1 Engine Room Relay Block and Junction Block Assembly
*2 AM2 Fuse


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Disconnect the cable from the positive (+) auxiliary battery terminal


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - Auxiliary battery positive (+) cable Power switch off Below 1 Ω
1 - Body ground Power switch off 10 kΩ or higher



e.

Connect the cable to the positive (+) auxiliary battery terminal.


f.

Connect the cable to the negative (-) auxiliary battery terminal.


g.

Install the AM2 fuse.



OK

5.CHECK HARNESS AND CONNECTOR (AM2 FUSE - HYBRID VEHICLE CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (AM2 FUSE - HYBRID VEHICLE CONTROL ECU)
a.

Remove the AM2 fuse from the engine room relay block and junction block assembly.


b.

Disconnect the L6 hybrid vehicle control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

U190789E02
6.083,1.688 6.448,1.958 true 0.417,0.073 1.063,0.385 0.646,0.313 10 false *1 2.125,0.76 2.771,1.073 0.646,0.313 10 false *2 3.448,0.073 4.094,0.385 0.646,0.313 10 false *a 6.479,1.885 6.927,2.198 0.448,0.313 10 false BATT 5.427,1.677 5.833,1.844 0.406,0.167 10 false L6

Text in Illustration
*1 Engine Room Relay Block and Junction Block Assembly *2 AM2 Fuse
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)
- -

Standard Resistance:
Tester Connection Switch Condition Specified Condition
2 (AM2 fuse terminal) - L6-3 (BATT) Power switch off Below 1 Ω



d.

Reconnect the L6 hybrid vehicle control ECU connector.


e.

Install the AM2 fuse.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR