Refer to the description for DTC P0A37-260 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A37-260).
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| P0A38 | 257 | Short to GND in the generator temperature sensor circuit | ·
Wire harness or connector ·
Power management control ECU ·
Hybrid vehicle generator assembly (Generator temperature sensor) |
| P0A39 | 259 | Open or short to +B in the generator temperature sensor circuit |
After confirming that DTC P0A38-257 or P0A39-259 is output, use the GTS to check "Motor Temp No2" in the power management control ECU Data List.
| Displayed Temperature | Malfunction |
|---|---|
| -40°C (-40°F) | Open circuit or short to +B |
| 215°C (419°F) | Short circuit or short to GND |
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
1. Turn the power switch on (IG) and wait for 5 seconds or more.
Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A2C-247
| Result | Proceed to |
|---|---|
| OK | A |
| NG (The connector is not connected securely.) | B |
| NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) | C |
A
B
C
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A2B-250
| Result | Proceed to |
|---|---|
| OK | A |
| NG (The connector is not connected securely.) | B |
| NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) | C |
A
B
C
Check the connection condition of the D7 hybrid vehicle generator assembly(generator temperature sensor) connector and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.
- The connector is connected securely.
- The terminals are not deformed and are connected securely.
- No water or foreign matter in the connector.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (The connector is not connected securely.) | B |
| NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) | C |
A
B
C
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / Motor Temp No2.
Read the Data List.
| Result | Proceed to |
|---|---|
| -40°C (-40°F) | A |
| 215°C (419°F) | B |
| Same as actual temperature | C |
Turn the power switch off.
A
B
C
Disconnect the D7 generator temperature sensor connector.
| *a | Component without harness connected
(Generator Temperature Sensor (Hybrid Vehicle Transaxle Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D7-8 (GMT) - D7-4 (GMTG) | Power switch off | 0.3436 to 1442 kΩ |
Connect the D7 generator temperature sensor connector.
OK
NG
Connect terminals 26 (GMT) and 27 (GMTG) of connector A21 of the power management control ECU.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / Motor Temp No2.
Read the Data List.
| Tester Display | Condition | Specified Condition |
| Motor Temp No2 | Terminals GMT and GMTG connected.
Power switch on (IG) |
215°C (419°F) |
| *a | Component with harness connected
(Power Management Control ECU) |
Turn the power switch off.
OK
NG
Disconnect the D7 generator temperature sensor connector.
| *a | Component without harness connected
(Generator Temperature Sensor (Hybrid Vehicle Transaxle Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D7-8 (GMT) - D7-4 (GMTG) | Power switch off | 0.3436 to 1442 kΩ |
Connect the D7 generator temperature sensor connector.
OK
NG
Disconnect the D7 generator temperature sensor connector.
Disconnect the A21 power management control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D7-8 (GMT) - A21-26 (GMT) | Power switch off | Below 1 Ω |
| D7-4 (GMTG) - A21-27 (GMTG) | Power switch off | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D7-8 (GMT) or A21-26 (GMT) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
| D7-4 (GMTG) or A21-27 (GMTG) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
| *a | Front view of wire harness connector
(to Generator Temperature Sensor) |
| *b | Rear view of wire harness connector
(to Power Management Control ECU) |
Reconnect the A21 power management control ECU connector.
Reconnect the D7 generator temperature sensor connector.
OK
NG