Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2012.03–2012.10
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301573 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0AEE-277  Motor Inverter Temperature Sensor "A" Circuit Range / Performance  P0AF1-276  Drive Motor Inverter Temperature Sensor "A" Circuit Intermittent / Erratic  


DESCRIPTION

The MG ECU located in the inverter with converter assembly detects the temperature of the motor inverter using the temperature sensor built into the motor inverter. If necessary, the MG ECU will limit inverter output to help prevent motor inverter overheating. The power management control ECU also detects malfunctions in the sensor based on the temperature sensor values. The inverter with converter assembly detects malfunctions in the motor inverter temperature sensor and its wiring.

DTC No. INF Code DTC Detection Condition Trouble Area
P0AEE 277 Motor inverter temperature calculated by the power management control ECU is different from the actual temperature for 10 seconds or more, and the motor inverter temperature is too high.
(1 trip detection logic)
·

Inverter cooling system

·

Cooling fan system

·

Inverter with converter assembly


P0AF1 276 Unusual sudden change in motor inverter temperature sensor output occurs and the offset continues, or unusual sudden change in motor inverter temperature sensor output occurs repeatedly.
(1 trip detection logic)

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the power switch on (READY) and wait for 90 seconds or more.

2.

Drive the vehicle for approximately 10 minutes referring to the following freeze frame data or Data List items: "Vehicle Spd".



PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check if DTCs are output.

Result:
Result Proceed to
P0AEE-277 or P0AF1-276 is output A
Any of the following DTCs are also output. B


DTC No. Relevant Diagnosis
P0A93-346 Inverter Cooling System Performance
P0C73-776 Motor Electronics Coolant Pump "A" Control Performance
P314A-828 Inverter Coolant Pump Speed Signal

HINT:

P0AEE-277 or P0AF1-276 may be set due to a malfunction which also causes DTCs in the preceding table to be set. In this case, first troubleshoot the output DTCs in the preceding table. Then, perform a test to attempt to reproduce the problems, and check that no DTCs are output.



e.

Turn the power switch off.



A

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

B

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

OK

3.CHECK QUANTITY OF HV COOLANT

NG

CONNECT SECURELY

3.CHECK QUANTITY OF HV COOLANT

A

4.CHECK COOLANT HOSE

B

ADD HV COOLANT

C

INSPECT FOR COOLANT LEAK AND ADD COOLANT

4.CHECK COOLANT HOSE

OK

5.PERFORM ACTIVE TEST USING GTS (CONTROL THE ELECTRIC COOLING FAN)

NG

CORRECT THE PROBLEM

5.PERFORM ACTIVE TEST USING GTS (CONTROL THE ELECTRIC COOLING FAN)

OK

6.CHECK HV COOLANT (CHECK FOR CONDITIONS THAT MAY HAVE CAUSED FREEZING)

NG

6.CHECK HV COOLANT (CHECK FOR CONDITIONS THAT MAY HAVE CAUSED FREEZING)

A

7.REPLACE HV COOLANT

B

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS