The ECM turns the fan relays on or off using signals calculated from the engine coolant temperature, air conditioning switch (on/off), air conditioning refrigerant pressure, engine speed, and vehicle speed signals.
The ECM switches the circuit of the cooling fan motors between series and parallel by turning the fan relays on or off in order to control the speed of the cooling fan motors in two steps.
Refer to System Diagram (See page Engine / Hybrid System>2ZR-FXE (COOLING)>COOLING FAN SYSTEM>SYSTEM DIAGRAM).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Electric Cooling Fan.
Check the operation of the cooling fans while operating them using the GTS.
| GTS Operation | Specified Condition |
|---|---|
| ON | Fans operate |
| OFF | Fans do not operate |
OK
NG
Remove the FAN No. 1 relay, FAN No. 2 relay and FAN No. 3 relay from the engine room relay block and junction block assembly.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (FAN No. 1 relay) - Body ground | Power switch on (IG) | 11 to 14 V |
| 1 (FAN No. 2 relay) - Body ground | Power switch on (IG) | 11 to 14 V |
| 1 (FAN No. 3 relay) - Body ground | Power switch on (IG) | 11 to 14 V |
| *1 | Engine Room Relay Block and Junction Block Assembly |
| *2 | FAN No. 1 Relay |
| *3 | FAN No. 2 Relay |
| *4 | FAN No. 3 Relay |
OK
NG
Remove the FAN No. 1 relay, FAN No. 2 relay and FAN No. 3 relay from the engine room relay block and junction block assembly.
Disconnect the A57 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (FAN No. 1 relay) - A57-22 (FANH) | Always | Below 1 Ω |
| 2 (FAN No. 2 relay) - A57-22 (FANH) | Always | Below 1 Ω |
| 2 (FAN No. 3 relay) - A57-21 (FANL) | Always | Below 1 Ω |
| 2 (FAN No. 1 relay) or A57-22 (FANH) - Body ground | Always | 10 kΩ or higher |
| 2 (FAN No. 2 relay) or A57-22 (FANH) - Body ground | Always | 10 kΩ or higher |
| 2 (FAN No. 3 relay) or A57-21 (FANL) - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the FAN No. 1 relay and FAN No. 3 relay from the engine room relay block and junction block assembly.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (FAN No. 1 relay) - Body ground | Power switch off | 11 to 14 V |
| 5 (FAN No. 3 relay) - Body ground | Power switch off | 11 to 14 V |
| *1 | Engine Room Relay Block and Junction Block Assembly |
| *2 | FAN No. 1 Relay |
| *3 | FAN No. 3 Relay |
OK
NG
Inspect the FAN No. 1 relay (See page Engine / Hybrid System>2ZR-FXE (COOLING)>RELAY>ON-VEHICLE INSPECTION).
OK
NG
Inspect the FAN No. 2 relay (See page Engine / Hybrid System>2ZR-FXE (COOLING)>RELAY>ON-VEHICLE INSPECTION).
OK
NG
Inspect the FAN No. 3 relay (See page Engine / Hybrid System>2ZR-FXE (COOLING)>RELAY>ON-VEHICLE INSPECTION).
OK
NG
Remove the FAN No. 2 relay from the engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5 (FAN No. 2 relay) - Body ground | Always | Below 1 Ω |
OK
NG
Inspect the cooling fan motor (See page Engine / Hybrid System>2ZR-FXE (COOLING)>COOLING FAN MOTOR>ON-VEHICLE INSPECTION).
OK
NG
Disconnect the A5 cooling fan motor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A5-1 - Body ground | Always | Below 1 Ω |
OK
NG
Disconnect the A5 cooling fan motor connector.
Remove the FAN No. 1 relay and FAN No. 2 relay from the engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A5-2 - 5 (FAN No. 1 relay) | Always | Below 1 Ω |
| A5-2 - 4 (FAN No. 2 relay) | Always | Below 1 Ω |
| A5-2 or 5 (FAN No. 1 relay) - Body ground | Always | 10 kΩ or higher |
| A5-2 or 4 (FAN No. 2 relay) - Body ground | Always | 10 kΩ or higher |
Make sure that there are no short circuits to the auxiliary battery.
OK
NG
Inspect the No. 2 cooling fan motor (See page Engine / Hybrid System>2ZR-FXE (COOLING)>COOLING FAN MOTOR>ON-VEHICLE INSPECTION).
OK
NG
Disconnect the A6 No. 2 cooling fan motor connector.
Remove the FAN No. 2 relay and FAN No. 3 relay from the engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A6-1 - 3 (FAN No. 2 relay) | Always | Below 1 Ω |
| A6-2 - 3 (FAN No. 3 relay) | Always | Below 1 Ω |
| A6-1 or 3 (FAN No. 2 relay) - Body ground | Always | 10 kΩ or higher |
| A6-2 or 3 (FAN No. 3 relay) - Body ground | Always | 10 kΩ or higher |
Make sure that there are no short circuits to the auxiliary battery.
OK
NG
Remove the FAN No. 1 relay, FAN No. 2 relay and FAN No. 3 relay from the engine room relay block and junction block assembly.
Disconnect the 1B No. 2 integration relay connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (FAN No. 1 relay) - 1B-4 | Always | Below 1 Ω |
| 1 (FAN No. 2 relay) - 1B-4 | Always | Below 1 Ω |
| 1 (FAN No. 3 relay) - 1B-4 | Always | Below 1 Ω |
| 1 (FAN No. 1 relay) or 1B-4 - Body ground | Always | 10 kΩ or higher |
| 1 (FAN No. 2 relay) or 1B-4 - Body ground | Always | 10 kΩ or higher |
| 1 (FAN No. 3 relay) or 1B-4 - Body ground | Always | 10 kΩ or higher |
OK
NG