Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2016.05–2020.08
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301573 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P2532-772  Ignition Switch Run Position Circuit High  


DESCRIPTION

The power source and HV CPU processors and their functions are integrated into the hybrid vehicle control ECU. The power source CPU and HV CPU use CAN communication to communicate with each other inside the hybrid vehicle control ECU. The power source CPU controls the opening and closing of the IG2 relay. The HV CPU detects that the IG2 relay is stuck ON (closed) based on relay operation information received from the power source CPU via CAN communication.

DTC No. INF Code DTC Detection Condition Trouble Area
P2532 772 Voltage is still applied to IG2 terminal although an IG2 relay off command is received from the power source CPU.
·

Wire harness or connector

·

No. 2 integration relay (IG2 relay)

·

Hybrid vehicle control ECU



HINT:

If DTC P2532-772 is stored, the vehicle will turn off.


WIRING DIAGRAM

A384272E08
0.365,0.875 1.24,1.448 0.875,0.573 10 false from Auxiliary Battery 2.25,2.167 4.698,2.365 2.448,0.198 10 false No. 2 Integration Relay 1.688,0.917 2,1.115 0.313,0.198 10 false 1C 1.698,1.365 2.01,1.563 0.313,0.198 10 false 1A 1.75,0.719 1.906,0.917 0.156,0.198 10 false 1 1.75,1.167 1.906,1.365 0.156,0.198 10 false 3 2.323,1.063 2.781,1.26 0.458,0.198 10 false IG2 3.135,1.75 3.594,1.948 0.458,0.198 10 false IG2 4.104,0.917 4.417,1.115 0.313,0.198 10 false 1A 4.094,1.365 4.406,1.563 0.313,0.198 10 false 1A 4.156,0.719 4.313,0.917 0.156,0.198 10 false 4 4.156,1.167 4.313,1.365 0.156,0.198 10 false 2 5.625,0.844 6.083,1.042 0.458,0.198 10 false IG2 5.448,0.833 5.604,1.031 0.156,0.198 10 false 3 5.26,1.604 7.125,1.99 1.865,0.385 10 false Hybrid Vehicle Control ECU 5.271,1.427 5.729,1.625 0.458,0.198 10 false A21 5.469,2.896 6.083,3.094 0.615,0.198 10 false L195 5.479,3.083 7,3.531 1.521,0.448 10 false Certification ECU (Smart Key ECU Assembly) 5.469,2.396 5.625,2.594 0.156,0.198 10 false 9 5.625,2.5 6.24,2.698 0.615,0.198 10 false IG2D

CAUTION / NOTICE / HINT

HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the power switch on (IG) and wait for 15 seconds or more.

2.

Turn the power switch off and wait for 30 seconds or more.



PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check for DTCs.


Result
Result Proceed to
P2532-772 only is output. A
DTCs except P2532-772 are output. B

e.

Turn the power switch off.



A

2.READ VALUE USING GTS (CAN BUS CHECK)

B

6.CHECK FOR INTERMITTENT PROBLEMS
2.READ VALUE USING GTS (CAN BUS CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: System Select / CAN Bus Check.


Result
Result Proceed to
All of the ECUs and sensors that are currently connected to the CAN communication system are displayed. A
None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed.
(w/ Central Gateway ECU)
B
None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed.
(w/o Central Gateway ECU)
C

d.

Turn the power switch off.



A

3.CHECK HARNESS AND CONNECTOR (+B SHORT)

B

C

3.CHECK HARNESS AND CONNECTOR (+B SHORT)
a.
U190782E03
0.844,2.281 1.219,2.573 false 0.667,2.938 0.938,3.104 0.271,0.167 10 false A21 1.271,2.542 1.656,2.719 0.385,0.177 10 false IG2 0.177,0.073 0.333,0.24 0.156,0.167 10 false *a

Disconnect the A21 hybrid vehicle control ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A21-3 (IG2) - Body ground Power switch off 1 V or less


Text in Illustration
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)


c.

Reconnect the A21 hybrid vehicle control ECU connector.



OK

NG

4.INSPECT NO. 2 INTEGRATION RELAY (IG2)
4.INSPECT NO. 2 INTEGRATION RELAY (IG2)

OK

5.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - NO. 2 INTEGRATION RELAY)

NG

5.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - NO. 2 INTEGRATION RELAY)
a.

Disconnect the A21 hybrid vehicle control ECU connector.


b.
U190782E04
0.844,2.281 1.219,2.573 false 0.667,2.927 0.938,3.094 0.271,0.167 10 false A21 1.271,2.531 1.656,2.708 0.385,0.177 10 false IG2 0.177,0.073 0.333,0.24 0.156,0.167 10 false *a

Remove the No. 2 integration relay from the engine room relay block and junction block assembly.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A21-3 (IG2) - Body ground Power switch off 1 V or less


Text in Illustration
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)


d.

Install the No. 2 integration relay.


e.

Reconnect the A21 hybrid vehicle control ECU connector.



OK

6.CHECK FOR INTERMITTENT PROBLEMS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK FOR INTERMITTENT PROBLEMS
a.

Check for intermittent problems. (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS)

i.

Check the connection and terminal contact pressure of the connectors and wire harnesses between the hybrid vehicle control ECU and the engine room relay block and junction block assembly.


ii.

When the power switch is on (READY), jiggle the connectors and wire harnesses between the hybrid vehicle control ECU and the engine room relay block and junction block assembly.



Result
Result Proceed to
Problem symptom does not recur. A
Problem symptom recurs. B


A

B

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA