Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2014.11–2016.05
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301573 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P2120-152  Throttle / Pedal Position Sensor / Switch "D" Circuit  P2121-106  Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance  P2122-104  Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input  P2123-105  Throttle / Pedal Position Sensor / Switch "D" Circuit High Input  P2125-153  Throttle / Pedal Position Sensor / Switch "E" Circuit  P2126-109  Throttle / Pedal Position Sensor / Switch "E" Circuit Range / Performance  P2127-107  Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input  P2128-108  Throttle / Pedal Position Sensor / Switch "E" Circuit High Input  P2138-110  Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation  P2138-154  Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation  


DESCRIPTION

The accelerator pedal position sensor is mounted on the accelerator pedal to detect how much the pedal is depressed. This is a non-contact sensor with hall elements. There are 2 outputs from the sensor. One is used to detect the accelerator pedal position and the other is used as a confirmation to allow the detection of a malfunction in the sensor itself. Voltage is output from the accelerator pedal position sensor to terminals VPA1 and VPA2 of the power management control ECU. This voltage varies from 0 to 5 V in accordance with the accelerator pedal position. Terminal VPA2 is primarily used to detect a malfunction in the sensor itself. The power management control ECU determines the current accelerator pedal position and controls the hybrid control system based on signals received by terminals VPA1 and VPA2.

A222964E66
0.76,2.708 0.76,3.427 0.76,3.427 0.854,3.427 false 0.76,1.615 0.76,0.75 0.76,0.75 0.865,0.75 false 0.74,2.01 0.219,0.385 0.219,0.385 0.302,0.385 false 0.75,2.354 0.198,3.813 0.198,3.813 0.281,3.813 false 0.896,0.677 1.406,0.844 0.51,0.167 10 false Magnet 0.333,0.313 1.188,0.479 0.854,0.167 10 false Hall Element 0.333,3.74 1.188,3.906 0.854,0.167 10 false Hall Element 0.885,3.344 1.396,3.51 0.51,0.167 10 false Magnet 1.74,3.552 3.021,3.948 1.281,0.396 10 false Power Management Control ECU 2.865,1.771 4.083,2.313 1.219,0.542 10 false Accelerator Pedal Position Sensor Output Voltage (V) 4.5,0.708 6.719,0.885 2.219,0.177 10 false Accelerator Pedal Turning Angle (°) 4.396,4.094 6.708,4.271 2.313,0.177 10 false *1: Accelerator Pedal Fully Released 4.396,4.385 6.771,4.563 2.375,0.177 10 false *2: Accelerator Pedal Fully Depressed 0.198,4.063 1.323,4.396 1.125,0.333 10 false Accelerator Pedal Position Sensor 2.146,1.083 2.396,1.25 0.25,0.167 10 false 5 V 4.229,1.01 4.323,1.177 0.094,0.167 10 false 5 4.229,2.396 4.323,2.563 0.094,0.167 10 false 0 3.938,1.271 4.323,1.438 0.385,0.167 10 false 3.988 3.938,1.469 4.323,1.635 0.385,0.167 10 false 3.188 4.104,1.938 4.323,2.104 0.219,0.167 10 false 1.6 6.865,1.135 7.156,1.302 0.292,0.167 10 false 4.55 6.865,1.354 7.156,1.521 0.292,0.167 10 false 3.75 6.656,2.5 6.833,2.667 0.177,0.167 10 false 20 4.25,2.823 4.427,2.99 0.177,0.167 10 false *1 6.031,2.823 6.208,2.99 0.177,0.167 10 false *2 5.104,2.5 5.427,2.667 0.323,0.167 10 false 15.9 4.104,2.156 4.323,2.323 0.219,0.167 10 false 0.8 2.5,1.948 2.75,2.115 0.25,0.167 10 false 5 V 2.198,1.677 2.406,1.844 0.208,0.167 10 false AD 2.354,2.552 2.563,2.719 0.208,0.167 10 false AD

DTC No. INF Code DTC Detection Condition Trouble Area
P2120 152 Main sensor circuit wiring malfunction or level is not stable
·

Wire harness or connector

·

Accelerator pedal sensor assembly

·

Power management control ECU


P2121 106 Internal error of the main sensor
P2122 104 Open or short to GND in the main sensor circuit
P2123 105 Short to +B in the main sensor circuit
P2125 153 Sub sensor circuit wiring malfunction or level is not stable
P2126 109 Internal error of the sub sensor
P2127 107 Open or short to GND in the sub sensor circuit
P2128 108 Short to +B in the sub sensor circuit
P2138 110 Difference between the main sensor value and sub sensor value is large.
154 Main or sub sensor circuit wiring malfunction

WIRING DIAGRAM

A169668E72
1.76,0.531 2.302,0.823 0.542,0.292 10 false VCP1 1.75,1.896 2.385,2.208 0.635,0.313 10 false VCP2 1.771,1.021 2.188,1.302 0.417,0.281 10 false VPA1 1.771,2.313 2.49,2.594 0.719,0.281 10 false VPA2 1.844,1.448 2.396,1.813 0.552,0.365 10 false EP1 0.375,3.021 0.854,3.333 0.479,0.313 10 false A29*1 1.771,2.76 2.354,3.052 0.583,0.292 10 false EPA2 5.323,0.469 6.135,0.865 0.813,0.396 10 false VCP1 5.073,0.469 5.438,0.729 0.365,0.26 10 false 18 5.063,0.896 5.469,1.156 0.406,0.26 10 false 26 5.063,1.344 5.458,1.677 0.396,0.333 10 false 34 5.063,1.781 5.51,2.083 0.448,0.302 10 false 19 5.063,2.208 5.396,2.469 0.333,0.26 10 false 27 5.063,2.667 5.344,2.906 0.281,0.24 10 false 35 5.323,1.781 5.948,2.073 0.625,0.292 10 false VCP2 5.323,0.906 5.958,1.281 0.635,0.375 10 false VPA1 5.323,2.219 5.896,2.469 0.573,0.25 10 false VPA2 5.323,1.354 5.781,1.594 0.458,0.24 10 false EP1 5.323,2.677 5.802,2.958 0.479,0.281 10 false EP2 0.375,3.188 2.615,3.375 2.24,0.188 10 false Accelerator Pedal Sensor Assembly 4.885,3.083 5.5,3.406 0.615,0.323 10 false A22 4.875,3.24 6.917,3.469 2.042,0.229 10 false Power Management Control ECU 2.26,0.458 2.708,0.771 0.448,0.313 10 false 4 2.26,0.896 2.854,1.219 0.594,0.323 10 false 6 2.26,1.333 2.677,1.635 0.417,0.302 10 false 5 2.26,1.771 2.771,2.115 0.51,0.344 10 false 1 2.26,2.219 2.594,2.51 0.333,0.292 10 false 3 2.26,2.646 2.688,2.979 0.427,0.333 10 false 2 6.104,1.719 6.344,1.865 0.24,0.146 10 false 5 V 6.104,0.375 6.344,0.521 0.24,0.146 10 false 5 V 5.802,1.156 6.313,1.49 0.51,0.333 10 false 39 kΩ +/- 5% 5.792,2.479 6.313,2.823 0.521,0.344 10 false 39 kΩ +/- 5% 0.375,2.854 0.854,3.167 0.479,0.313 10 false A81*2 0.49,3.5 1.51,3.719 1.021,0.219 10 false *1: for LHD 1.427,3.5 2.448,3.719 1.021,0.219 10 false *2: for RHD

CAUTION / NOTICE / HINT

HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Wait for approximately 10 seconds with the power switch on (READY) and park (P) selected, then fully depress and release the accelerator pedal several times.



PROCEDURE

1.READ VALUE USING GTS (ACCEL PEDAL POS #1, ACCEL PEDAL POS #2)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Accel Pedal Pos #1, Accel Pedal Pos #2.


d.

Read the Data List.

Result:
Tester Display Accelerator Pedal Condition Specified Condition
Accel Pedal Pos #1 Not depressed 8 to 28%
Fully depressed 62 to 92%
Not depressed → Fully depressed → Not depressed (Accelerator pedal should be operated slowly) Value changes progressively
Accel Pedal Pos #2 Not depressed 20 to 44%
Fully depressed 78 to 100%
Not depressed → Fully depressed → Not depressed (Accelerator pedal should be operated slowly) Value changes progressively



e.

Turn the power switch off.



OK

NG

2.CHECK CONNECTOR CONNECTION CONDITION (ACCELERATOR PEDAL SENSOR ASSEMBLY CONNECTOR)
2.CHECK CONNECTOR CONNECTION CONDITION (ACCELERATOR PEDAL SENSOR ASSEMBLY CONNECTOR)
a.
U190749E02
0.048,0.025 0.268,0.196 0.220,0.170 10 *A 0.048,2.565 0.268,2.735 0.220,0.170 10 *B 1.835,0.434 2.099,0.616 0.264,0.181 10 A29 2.146,2.714 2.410,2.896 0.264,0.181 10 A81 1.231,0.605 1.432,0.605 false 1.502,2.845 1.703,2.845 false

Check the connector connections and contact pressure of the relevant terminals for the accelerator pedal sensor assembly connector A29*1, A81*2 (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE). ()

*1: for LHD

*2: for RHD


Text in Illustration
*A for LHD
*B for RHD

OK:

The connectors are connected securely and there are no contact pressure problems.




OK

3.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)

NG

CONNECT SECURELY

3.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)

OK

4.CHECK POWER MANAGEMENT CONTROL ECU (CHECK VOLTAGE)

NG

CONNECT SECURELY

4.CHECK POWER MANAGEMENT CONTROL ECU (CHECK VOLTAGE)
a.

Disconnect the A29 accelerator pedal sensor assembly connector. (for LHD)


b.

Disconnect the A81 accelerator pedal sensor assembly connector. (for RHD)


c.

Turn the power switch on (IG).


d.
U190595E02
0.73,1.828 1.162,1.983 0.433,0.155 10 VCP2 1.304,1.828 1.737,1.983 0.433,0.155 10 EP2 1.841,1.828 2.273,1.983 0.433,0.155 10 VCP1 2.449,1.828 2.753,1.983 0.304,0.155 10 EP1 1.338,1.144 0.946,1.828 false 1.495,1.144 1.456,1.844 false 1.812,1.144 2.055,1.828 false 1.952,1.146 2.597,1.828 false 2.808,1.186 3.072,1.367 0.264,0.181 10 A81 2.808,0.842 3.072,1.023 0.264,0.181 10 A29 0.19,0.1 0.364,0.261 0.174,0.161 10 *a 3.215,0.839 3.389,1.000 0.174,0.161 10 *A 3.215,1.183 3.389,1.344 0.174,0.161 10 *B

Measure the voltage according to the value(s) in the table below.

Standard Voltage :
Tester Connection Condition Specified Condition
A29-4 (VCP1) - A29-5 (EP1) Power switch on (IG) 4.5 to 5.5 V
A29-1 (VCP2) - A29-2 (EP2) Power switch on (IG) 4.5 to 5.5 V

Tester Connection Condition Specified Condition
A81-4 (VCP1) - A81-5 (EP1) Power switch on (IG) 4.5 to 5.5 V
A81-1 (VCP2) - A81-2 (EP2) Power switch on (IG) 4.5 to 5.5 V



Text in Illustration
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Accelerator Pedal Sensor Assembly)

e.

Reconnect the A29 accelerator pedal sensor assembly connector. (for LHD)


f.

Reconnect the A81 accelerator pedal sensor assembly connector. (for RHD)


g.

Turn the power switch off.



OK

5.CHECK POWER MANAGEMENT CONTROL ECU (CHECK RESISTANCE)

NG

7.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - ACCELERATOR PEDAL SENSOR)
5.CHECK POWER MANAGEMENT CONTROL ECU (CHECK RESISTANCE)
a.

Disconnect the A29 accelerator pedal sensor assembly connector. (for LHD)


b.

Disconnect the A81 accelerator pedal sensor assembly connector. (for RHD)


c.
U190596E02
1.322,1.852 1.755,2.006 0.433,0.155 10 VPA2 0.786,1.852 1.218,2.006 0.433,0.155 10 EP2 2.372,1.852 2.804,2.006 0.433,0.155 10 VPA1 1.93,1.852 2.234,2.006 0.304,0.155 10 EP1 1.492,1.15 0.954,1.851 false 1.948,1.152 2.095,1.835 false 2.787,0.831 3.051,1.012 0.264,0.181 10 A29 2.787,1.192 3.051,1.373 0.264,0.181 10 A81 0.187,0.106 0.361,0.267 0.174,0.161 10 *a 1.649,1.146 1.552,1.852 false 2.132,1.167 2.585,1.852 false 3.212,0.828 3.386,0.989 0.174,0.161 10 *A 3.212,1.189 3.386,1.350 0.174,0.161 10 *B

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A29-6 (VPA1) - A29-5 (EP1) Power switch off 36.60 to 41.61 kΩ
A29-3 (VPA2) - A29-2 (EP2) Power switch off 36.60 to 41.61 kΩ

Tester Connection Condition Specified Condition
A81-6 (VPA1) - A81-5 (EP1) Power switch off 36.60 to 41.61 kΩ
A81-3 (VPA2) - A81-2 (EP2) Power switch off 36.60 to 41.61 kΩ



Text in Illustration
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Accelerator Pedal Sensor Assembly)

d.

Reconnect the A29 accelerator pedal sensor assembly connector. (for LHD)


e.

Reconnect the A81 accelerator pedal sensor assembly connector. (for RHD)



OK

NG

6.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - ACCELERATOR PEDAL SENSOR)
6.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - ACCELERATOR PEDAL SENSOR)
a.

Disconnect the A29 accelerator pedal sensor assembly connector. (for LHD)


b.

Disconnect the A81 accelerator pedal sensor assembly connector. (for RHD)


c.
A379071E05
2.583,1.833 3,2.083 0.417,0.25 2.75,3.583 3.167,3.833 0.417,0.25 2.75,3.885 3.167,4.135 0.417,0.25 1.188,2.063 1.833,1.833 false 1.188,2.135 1.833,2.333 false 0.583,1.833 1.146,2.063 false 0.583,2.333 1.146,2.125 false 1,4.333 1.5,3.75 false 1.5,4.333 1.667,3.719 false 2.167,4.333 1.979,3.729 false 2.667,4.333 2.125,3.75 false 0.083,0.073 0.594,0.396 0.51,0.323 10 false *a 0.073,2.896 0.583,3.219 0.51,0.323 10 false *b 1.896,1.729 2.406,2.052 0.51,0.323 10 false VPA1 1.896,2.271 2.406,2.594 0.51,0.323 10 false EP1 2.656,1.875 3.167,2.198 0.51,0.323 10 false A22 2.823,3.625 3.333,3.948 0.51,0.323 10 false A29 0.25,2.25 0.76,2.573 0.51,0.323 10 false EP2 0.167,1.729 0.677,2.052 0.51,0.323 10 false VPA2 0.781,4.344 1.292,4.667 0.51,0.323 10 false EP2 1.292,4.365 1.813,4.667 0.521,0.302 10 false VPA2 2.51,4.365 3.021,4.667 0.51,0.302 10 false VPA1 2.042,4.375 2.552,4.656 0.51,0.281 10 false EP1 2.833,3.927 3.344,4.25 0.51,0.323 10 false A81 3.198,3.625 3.427,3.823 0.229,0.198 10 false *A 3.198,3.906 3.427,4.104 0.229,0.198 10 false *B

Disconnect the A22 power management control ECU connector.


d.

Turn the power switch on (IG).


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage :
Tester Connection Condition Specified Condition
A22-26 (VPA1) - Body ground Power switch on (IG) Below 1 V
A22-27 (VPA2) - Body ground Power switch on (IG) Below 1 V
A22-34 (EP1) - Body ground Power switch on (IG) Below 1 V
A22-35 (EP2) - Body ground Power switch on (IG) Below 1 V


Text in Illustration
*A for LHD
*B for RHD
*a Rear view of wire harness connector
(to Power Management Control ECU)
*b Front view of wire harness connector
(to Accelerator Pedal Sensor Assembly)

NOTICE:

Turning the power switch on (IG) with the power management control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



f.

Turn the power switch off.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A22-26 (VPA1) - A29-6 (VPA1) Power switch off Below 1 Ω
A22-34 (EP1) - A29-5 (EP1) Power switch off Below 1 Ω
A22-27 (VPA2) - A29-3 (VPA2) Power switch off Below 1 Ω
A22-35 (EP2) - A29-2 (EP2) Power switch off Below 1 Ω

Tester Connection Condition Specified Condition
A22-26 (VPA1) - A81-6 (VPA1) Power switch off Below 1 Ω
A22-34 (EP1) - A81-5 (EP1) Power switch off Below 1 Ω
A22-27 (VPA2) - A81-3 (VPA2) Power switch off Below 1 Ω
A22-35 (EP2) - A81-2 (EP2) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A22-26 (VPA1) or A29-6 (VPA1) - Body ground and other terminals Power switch off 10 kΩ or higher
A22-34 (EP1) or A29-5 (EP1) - Body ground and other terminals Power switch off 10 kΩ or higher
A22-27 (VPA2) or A29-3 (VPA2) - Body ground and other terminals Power switch off 10 kΩ or higher
A22-35 (EP2) or A29-2 (EP2) - Body ground and other terminals Power switch off 10 kΩ or higher

Tester Connection Condition Specified Condition
A22-26 (VPA1) or A81-6 (VPA1) - Body ground and other terminals Power switch off 10 kΩ or higher
A22-34 (EP1) or A81-5 (EP1) - Body ground and other terminals Power switch off 10 kΩ or higher
A22-27 (VPA2) or A81-3 (VPA2) - Body ground and other terminals Power switch off 10 kΩ or higher
A22-35 (EP2) or A81-2 (EP2) - Body ground and other terminals Power switch off 10 kΩ or higher



h.

Reconnect the A22 power management control ECU connector.


i.

Reconnect the A29 accelerator pedal sensor assembly connector. (for LHD)


j.

Reconnect the A81 accelerator pedal sensor assembly connector. (for RHD)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - ACCELERATOR PEDAL SENSOR)
a.

Disconnect the A29 accelerator pedal sensor assembly connector. (for LHD)


b.

Disconnect the A81 accelerator pedal sensor assembly connector. (for RHD)


c.

Disconnect the A22 power management control ECU connector.


d.

Turn the power switch on (IG).


e.
A379071E06
2.583,1.833 3,2.083 0.417,0.25 2.75,3.583 3.167,3.833 0.417,0.25 2.75,3.885 3.167,4.135 0.417,0.25 1.188,1.99 1.833,1.76 false 1.188,2.135 1.833,2.333 false 0.573,1.771 1.135,2 false 0.583,2.333 1.146,2.125 false 0.833,4.333 1.333,3.75 false 1.344,4.333 1.51,3.719 false 2.01,4.333 1.823,3.729 false 2.51,4.333 1.969,3.75 false 0.083,0.073 0.594,0.396 0.51,0.323 10 false *a 0.073,2.896 0.583,3.219 0.51,0.323 10 false *b 1.885,1.667 2.396,1.99 0.51,0.323 10 false VCP1 1.896,2.271 2.406,2.594 0.51,0.323 10 false EP1 2.656,1.875 3.167,2.198 0.51,0.323 10 false A22 2.823,3.625 3.333,3.948 0.51,0.323 10 false A29 0.25,2.25 0.76,2.573 0.51,0.323 10 false EP2 0.177,1.677 0.688,2 0.51,0.323 10 false VCP2 0.646,4.344 1.156,4.667 0.51,0.323 10 false VCP2 1.219,4.365 1.74,4.667 0.521,0.302 10 false EP2 2.51,4.365 3.021,4.667 0.51,0.302 10 false EP1 1.875,4.375 2.385,4.656 0.51,0.281 10 false VCP1 2.833,3.927 3.344,4.25 0.51,0.323 10 false A81 3.208,3.615 3.427,3.813 0.219,0.198 10 false *A 3.208,3.917 3.427,4.115 0.219,0.198 10 false *B

Measure the voltage according to the value(s) in the table below.

Standard Voltage :
Tester Connection Condition Specified Condition
A22-18 (VCP1) - Body ground Power switch on (IG) Below 1 V
A22-34 (EP1) - Body ground Power switch on (IG) Below 1 V
A22-19 (VCP2) - Body ground Power switch on (IG) Below 1 V
A22-35 (EP2) - Body ground Power switch on (IG) Below 1 V


Text in Illustration
*A for LHD
*B for RHD
*a Rear view of wire harness connector
(to Power Management Control ECU)
*b Front view of wire harness connector
(to Accelerator Pedal Sensor Assembly)

NOTICE:

Turning the power switch on (IG) with the power management control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



f.

Turn the power switch off.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A22-18 (VCP1) - A29-4 (VCP1) Power switch off Below 1 Ω
A22-34 (EP1) - A29-5 (EP1) Power switch off Below 1 Ω
A22-19 (VCP2) - A29-1 (VCP2) Power switch off Below 1 Ω
A22-35 (EP2) - A29-2 (EP2) Power switch off Below 1 Ω

Tester Connection Condition Specified Condition
A22-18 (VCP1) - A81-4 (VCP1) Power switch off Below 1 Ω
A22-34 (EP1) - A81-5 (EP1) Power switch off Below 1 Ω
A22-19 (VCP2) - A81-1 (VCP2) Power switch off Below 1 Ω
A22-35 (EP2) - A81-2 (EP2) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A22-18 (VCP1) or A29-4 (VCP1) - Body ground and other terminals Power switch off 10 kΩ or higher
A22-34 (EP1) or A29-5 (EP1) - Body ground and other terminals Power switch off 10 kΩ or higher
A22-19 (VCP2) or A29-1 (VCP2) - Body ground and other terminals Power switch off 10 kΩ or higher
A22-35 (EP2) or A29-2 (EP2) - Body ground and other terminals Power switch off 10 kΩ or higher

Tester Connection Condition Specified Condition
A22-18 (VCP1) or A81-4 (VCP1) - Body ground and other terminals Power switch off 10 kΩ or higher
A22-34 (EP1) or A81-5 (EP1) - Body ground and other terminals Power switch off 10 kΩ or higher
A22-19 (VCP2) or A81-1 (VCP2) - Body ground and other terminals Power switch off 10 kΩ or higher
A22-35 (EP2) or A81-2 (EP2) - Body ground and other terminals Power switch off 10 kΩ or higher



h.

Reconnect the A22 power management control ECU connector.


i.

Reconnect the A29 accelerator pedal sensor assembly connector. (for LHD)


j.

Reconnect the A81 accelerator pedal sensor assembly connector. (for RHD)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR