When selecting ECO mode, the ECO mode switch (combination switch assembly) operation signal is sent to the air conditioning amplifier assembly. Following this, ECO mode control is activated for the heater and air conditioning system.
A
B
C
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Body Electrical / Combination Meter / Active Test / Indicat. ECO Mode.
Perform the "Indicat. ECO MODE" Active Test.
The ECO MODE indicator light comes on or blinks.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (w/o Multi-information Display) | B |
| NG (w/ Multi-information Display) | C |
Turn the power switch off.
A
B
C
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / ECO Mode.
Read the value displayed on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition |
|---|---|---|
| ECO Mode | ECO mode transition availability/
ON or OFF |
In ECO mode: ON |
| Result | Proceed to |
|---|---|
| The GTS display changes according to the ECO mode switch (combination switch assembly) operation. | A |
| The GTS display does not changes according to the ECO mode switch (combination switch assembly) operation. | B |
Turn the power switch off.
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Body Electrical / Air Conditioning / Data List / ECO Switch.
Read the value displayed on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition |
|---|---|---|
| ECO Switch | ECO switch condition/
ON or OFF |
ECO switch being pushed and held: ON
ECO switch not pushed: OFF |
| Result | Proceed to |
|---|---|
| The GTS display changes according to the ECO mode switch (combination switch assembly) operation. | A |
| The GTS display does not changes according to the ECO mode switch (combination switch assembly) operation. | B |
Turn the power switch off.
A
B
Remove the ECO mode switch (combination switch assembly).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 5 (ECU) - 3 (E) | ECO mode switch (combination switch assembly) being pushed and held | Below 1 Ω |
| ECO mode switch (combination switch assembly) not pushed | 10 kΩ or higher |
| *a | Component without harness connected
(ECO Mode Switch (Combination Switch Assembly)) |
Install the ECO mode switch (combination switch assembly).
OK
NG
Disconnect the L143 ECO mode switch (combination switch assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L143-3 (E) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector
(to ECO Mode Switch (Combination Switch Assembly)) |
Reconnect the L143 ECO mode switch (combination switch assembly) connector.
OK
NG
Disconnect the L17 air conditioning amplifier assembly connector.
Disconnect the L143 ECO mode switch (combination switch assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L17-15 (ECOS) - L143-5 (ECU) | Always | Below 1 Ω |
| L17-15 (ECOS) or L143-5 (ECU) - Body ground | Always | 10 kΩ or higher |
| *a | Front view of wire harness connector
(to Air Conditioning Amplifier Assembly) |
| *b | Front view of wire harness connector
(to ECO Mode Switch (Combination Switch Assembly)) |
Reconnect the L143 ECO mode switch (combination switch assembly) connector.
Reconnect the L17 air conditioning amplifier assembly connector.
OK
NG