The Power management control ECU monitors its internal operation, it will set DTCs and perform fail-safe control when it detects the following malfunctions.
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| P0C30 | 390 | Charge control error | ·
Power management control ECU ·
Hybrid battery junction block assembly ·
HV battery |
When performing P0C30-390 troubleshooting, use either a tool wrapped with vinyl insulation tape or a insulated tool. (It is extremely dangerous when a high-voltage charge passes through a non-insulated tool causing a short.)
Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
When the vehicle is stopped with the power switch on (READY) and drive (D) selected, depress the accelerator pedal. The engine rpm will increase as well as "State of Charge (All Bat)". If charge current drops, release the accelerator pedal and then depress it again to maintain charging.
Check that charging stops when "State of Charge (All Bat)" reaches the upper limit.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check if DTCs are output.
| Result | Proceed to |
|---|---|
| P0C30-390 only is output. | A |
| DTCs other than P0C30-390 are output. | B |
Turn the power switch off.
A
B
(See pageEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART)
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Read the freeze frame data of DTC P0C30-390.
| Result | Proceed to |
|---|---|
| OFF is displayed for "Ready Signal", "SMRP Status", "SMRB Status" and "SMRG Status" and -0.5 A or less is displayed for "Batt Pack Current Val" for all of the freeze frame data items. | A |
| Other than above | B |
As the power switch on (IG) state may cause the DTC to be stored, freeze frame data is used to judge the cause of the DTC output.
Turn the power switch off.
A
B
Be sure to wear insulated gloves.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the No. 2 hybrid battery shield sub-assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL).
Disconnect the high voltage cable connectors from the hybrid battery junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| T6-1 (CBI) - k3-1 (+) | Power switch off | 10 kΩ or higher |
If a system main relay is stuck closed, inspect the hybrid battery junction block assembly without removing it from the vehicle, in order to keep the relay closed.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| T5-1 (CEI) - h3-1 (-) | Power switch off | 10 kΩ or higher |
If a system main relay is stuck closed, inspect the hybrid battery junction block assembly without removing it from the vehicle, in order to keep the relay closed.
If the resistance is between 28.5 and 31.5 Ω, it can be determined that SMRP is stuck closed.
Connect the high voltage cable connectors.
Install the No. 2 hybrid battery shield sub-assembly.
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (READY).
Perform a road test.
Accelerate/decelerate gently. Avoid rapid acceleration/deceleration.
Enter the following menus: Powertrain / Hybrid Control / Data List / Batt Pack Current Val.
Drive the vehicle with the value of Data List item "Batt Pack Current Val" between -50 A and 50 A.
Distance and driving time are not specified.
Turn the power switch off and leave the vehicle for 30 seconds or more.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / Batt Pack Current Val.
Check that the value of "Batt Pack Current Val" is between - 0.5 A and 0.5 A with the power switch on (IG).
If the value is outside the specified range, perform the road test again.
If the power switch is on (IG) and value of "Batt Pack Current Val" is between - 0.5 A and 0.5 A, current sensor offset learning has been completed.
Even if the current sensor offset learning is not complete, the current sensor value will be corrected by repeating the road test a maximum of 7 times.
NEXT
Connect the GTS to the DLC3.
Apply the parking brake and secure the wheels using chocks.
Turn the power switch on (READY).
Enter the following menus: Powertrain / Hybrid Control / Data List / State of Charge (All Bat) and Charge Control Value.
Check that "State of Charge (All Bat)" shows 60% or less.
If "State of Charge (All Bat)" is 60% or more, reduce it to below 60% by leaving the hybrid system on with the neutral (N) selected.
Ensure the safety of the areas in front and at the back of the vehicle.
Read the Data List "Charge Control Value".
Drive (D) selected and depress both the accelerator pedal and brake pedal at the same time.
| Result | Proceed to |
|---|---|
| "Charge Control Value" is 0 kW. | A |
| "Charge Control Value" is not 0 kW. | B |
Turn the power switch off.
A
B