Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2012.03–2016.05
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301573 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P3107-214  Lost Communication with Airbag System Control Module  


DESCRIPTION

Refer to the description for DTC P3107-213 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P3107-213).


DTC No. INF Code DTC Detection Condition Trouble Area
P3107 214 Open or short to +B in the communication circuit
·

Wire harness or connector

·

Airbag ECU assembly

·

Power management control ECU



WIRING DIAGRAM

Refer to the wiring diagram for DTC P0AE6-225 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AE6-225).

Refer to the wiring diagram for DTC P3107-213 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P3107-213).

CAUTION / NOTICE / HINT

HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the power switch on (IG) and wait for 15 seconds or more.



PROCEDURE

1.CHECK DTC OUTPUT (SRS AIRBAG)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Body Electrical / SRS Airbag / Trouble Codes.


d.

Check if DTCs are output.


Result:
Result Proceed to
Airbag system DTCs are not output. A
Airbag system DTCs are output. B


e.

Turn the power switch off.



A

2.CHECK AIRBAG ECU ASSEMBLY (CHECK WAVEFORM)

B

2.CHECK AIRBAG ECU ASSEMBLY (CHECK WAVEFORM)

A

3.CLEAR DTC

B

6.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)
3.CLEAR DTC

NEXT

4.CHECK DTC OUTPUT (HYBRID CONTROL)
4.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check if DTCs are output.

Result:
Result Proceed to
DTC P3107-214 is not output. A
DTC P3107-214 is output again. B



e.

Turn the power switch off.



A

5.CHECK FOR INTERMITTENT PROBLEMS

B

5.CHECK FOR INTERMITTENT PROBLEMS

OK

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

6.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)

OK

7.CHECK CONNECTOR CONNECTION CONDITION (AIRBAG ECU ASSEMBLY CONNECTOR)

NG

CONNECT SECURELY

7.CHECK CONNECTOR CONNECTION CONDITION (AIRBAG ECU ASSEMBLY CONNECTOR)
a.
A216765E04
0.104,0 0.349,0.233 0.246,0.233 10 *a

Check the connector connections and contact pressure of the relevant terminals for the airbag ECU assembly connectors.

Text in Illustration
*a Component with harness connected
(Airbag ECU Assembly)

OK:

The connectors are connected securely and there are no contact pressure problems.




OK

8.CHECK HARNESS AND CONNECTOR (+B SHORT)

NG

CONNECT SECURELY

8.CHECK HARNESS AND CONNECTOR (+B SHORT)
a.
A238663E01
0.135,0.169 0.402,0.362 0.267,0.193 10 *1 2.913,0.771 3.180,0.963 0.267,0.193 10 *2 2.919,1.659 3.186,1.852 0.267,0.193 10 *3 1.779,1.266 2.876,0.877 false 2.215,1.971 2.899,1.773 false

Remove the IGCT NO. 2 fuse and AM2 fuse from the engine room relay block and junction block assembly.

Text in Illustration
*1 Engine Room Relay Block and Junction Block Assembly
*2 AM2 Fuse
*3 IGCT NO. 2 Fuse


b.
U190572E02
0.094,0.083 0.344,0.302 0.25,0.219 10 false *a 1.677,1.385 1.948,1.552 0.271,0.167 10 false L16

Disconnect the L16 airbag ECU assembly connector.

Text in Illustration
*a Component without harness connected
(Airbag ECU Assembly)


c.
U154394E01
0.165,0.134 0.330,0.299 0.165,0.165 10 *a 1.881,2.396 2.261,2.562 0.380,0.165 10 ABFS 0.646,0.979 0.925,1.142 0.279,0.163 10 A21 1.25,0.979 1.529,1.142 0.279,0.163 10 A22 1.961,0.979 2.168,1.142 0.207,0.163 10 L5 2.542,0.979 2.740,1.142 0.198,0.163 10 L6 0.498,2.396 0.766,2.578 0.268,0.181 10 +B2 0.045,2.86 0.413,3.000 0.369,0.140 10 FCTL 1.026,2.396 1.294,2.578 0.268,0.181 10 +B1 0.944,1.701 0.671,2.389 false 0.102,2.396 0.269,2.578 0.166,0.181 10 GI 0.649,1.77 0.224,2.396 false 0.815,1.701 0.264,2.847 false 1.338,1.693 1.199,2.389 false 1.494,2.396 1.736,2.578 0.242,0.181 10 IG2 1.673,1.701 1.625,2.39 false 0.564,2.86 0.972,3.007 0.409,0.146 10 MREL 1.269,1.701 0.815,2.847 false 1.925,1.775 1.81,2.851 false 2.785,1.702 2.943,2.851 false 1.14,2.86 1.491,3.000 0.351,0.140 10 IG2D 1.61,1.701 1.326,2.851 false 2.193,2.86 2.575,3.000 0.382,0.140 10 AM22 2.75,2.86 3.095,3.000 0.346,0.140 10 IG1D 2.421,2.42 2.801,2.559 0.380,0.139 10 AM21 2.249,1.701 2.423,2.845 false 2.852,1.7 3.162,2.412 false 2.45,1.703 2.659,2.415 false 1.597,2.86 1.945,3.002 0.348,0.142 10 SPDI 2.936,2.42 3.356,2.562 0.420,0.142 10 ACCD 2.247,1.906 2.116,2.389 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L5-29 (ABFS) - A21-2 (+B2) Power switch off 10 kΩ or higher
L5-29 (ABFS) - A22-5 (+B1) Power switch off 10 kΩ or higher
L5-29 (ABFS) - L5-1 (AM22) Power switch off 10 kΩ or higher
L5-29 (ABFS) - L6-7 (AM21) Power switch off 10 kΩ or higher
L5-29 (ABFS) - A22-6 (MREL) Power switch off 10 kΩ or higher
L5-29 (ABFS) - A22-1 (IG2) Power switch off 10 kΩ or higher
L5-29 (ABFS) - L6-1 (ACCD) Power switch off 10 kΩ or higher
L5-29 (ABFS) - L6-2 (IG1D) Power switch off 10 kΩ or higher
L5-29 (ABFS) - A22-2 (IG2D) Power switch off 10 kΩ or higher
L5-29 (ABFS) - L5-14 (SPDI) Power switch off 10 kΩ or higher
L5-29 (ABFS) - A21-16 (GI) Power switch off 10 kΩ or higher
L5-29 (ABFS) - A21-4 (FCTL) Power switch off 10 kΩ or higher


Text in Illustration
*a Component with harness connected
(Power Management Control ECU)


d.

Reconnect the L16 airbag ECU assembly connector.


e.

Install the IGCT NO. 2 fuse and AM2 fuse.



OK

9.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - AIRBAG ECU ASSEMBLY)

NG

11.CHECK HARNESS AND CONNECTOR (SHORT TO POWER SUPPLY WIRES)
9.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - AIRBAG ECU ASSEMBLY)
a.

Disconnect the L5 power management control ECU connector.


b.

Disconnect the L16 airbag ECU assembly connector.


c.
U190574E02
2.25,1.833 2.552,2.063 false 1.271,3.854 1.771,4.229 false 0.073,0.042 0.344,0.24 0.271,0.198 10 false *a 0.115,2.406 0.385,2.604 0.271,0.198 10 false *b 1.385,1.573 1.656,1.74 0.271,0.167 10 false L5 1.708,3.729 1.979,3.896 0.271,0.167 10 false L16 2.563,2.063 3.031,2.26 0.469,0.198 10 false ABFS 1.781,4.24 2.417,4.458 0.635,0.219 10 false GSW2

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
L5-29 (ABFS) - L16-14 (GSW2) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
L5-29 (ABFS) or L16-14 (GSW2) - Body ground and other terminals Power switch off 10 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)
*b Rear view of wire harness connector
(to Airbag ECU Assembly)

HINT:

As necessary, check that there is no short to power supply wires when performing the above wire harness inspection.



d.

Reconnect the airbag ECU assembly connector.


e.

Reconnect the power management control ECU connector.



OK

10.CHECK POWER MANAGEMENT CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK POWER MANAGEMENT CONTROL ECU
a.
U190572E02
0.094,0.083 0.344,0.302 0.25,0.219 10 false *a 1.677,1.385 1.948,1.552 0.271,0.167 10 false L16

Disconnect the L16 airbag ECU assembly connector.

Text in Illustration
*a Component without harness connected
(Airbag ECU Assembly)


b.

Turn the power switch on (IG).


c.
U154402E03
2.24,1.906 2.521,2.531 false 2.385,2.563 2.875,2.74 0.49,0.177 10 false ABFS 0.135,0.052 0.292,0.229 0.156,0.177 10 false *a 1.99,0.969 2.25,1.146 0.26,0.177 10 false L5

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L5-29 (ABFS) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Component with harness connected
(Power Management Control ECU)

NOTICE:

Turning the power switch on (IG) with the airbag ECU assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



d.

Turn the power switch off.


e.

Reconnect the L16 airbag ECU assembly connector.



OK

NG

11.CHECK HARNESS AND CONNECTOR (SHORT TO POWER SUPPLY WIRES)
a.
A238663E02
0.135,0.169 0.402,0.362 0.267,0.193 10 *1 2.913,0.771 3.181,0.964 0.267,0.193 10 *2 2.919,1.659 3.186,1.852 0.267,0.193 10 *3 1.779,1.266 2.876,0.877 false 2.215,1.971 2.899,1.773 false

Remove the IGCT NO. 2 fuse and AM2 fuse from the engine room relay block and junction block assembly.

Text in Illustration
*1 Engine Room Relay Block and Junction Block Assembly
*2 AM2 Fuse
*3 IGCT NO. 2 Fuse


b.
U190572E02
0.094,0.083 0.344,0.302 0.25,0.219 10 false *a 1.677,1.385 1.948,1.552 0.271,0.167 10 false L16

Disconnect the L16 airbag ECU assembly connector.

Text in Illustration
*a Component without harness connected
(Airbag ECU Assembly)


c.

Disconnect the A21, A22, L5 and L6 power management control ECU connectors.


d.
U154393E01
0.418,1.398 0.682,1.579 0.264,0.181 10 A21 0.187,0.103 0.343,0.285 0.156,0.181 10 *a 1.174,1.404 1.438,1.585 0.264,0.181 10 A22 2.048,1.405 2.257,1.586 0.209,0.181 10 L5 2.815,1.388 3.025,1.569 0.210,0.181 10 L6 2.344,2.288 2.373,3.036 false 2.145,3.055 2.545,3.237 0.400,0.181 10 ABFS 0.472,2.763 0.740,2.944 0.268,0.181 10 +B2 0.025,3.055 0.394,3.195 0.369,0.140 10 FCTL 0.957,2.763 1.225,2.944 0.268,0.181 10 +B1 0.701,2.068 0.648,2.756 false 0.053,2.763 0.219,2.944 0.166,0.181 10 GI 0.406,2.137 0.168,2.763 false 0.572,2.068 0.249,3.05 false 1.249,2.078 1.114,2.749 false 1.429,2.763 1.671,2.944 0.242,0.181 10 IG2 1.596,2.078 1.574,2.763 false 0.536,3.055 0.944,3.202 0.409,0.146 10 MREL 1.189,2.078 0.792,3.055 false 2.027,2.141 1.774,3.055 false 3.071,2.069 2.873,3.055 false 1.099,3.055 1.450,3.195 0.351,0.140 10 IG2D 1.528,2.078 1.3,3.046 false 1.882,2.763 2.264,2.903 0.382,0.140 10 AM22 2.67,3.055 3.016,3.195 0.346,0.140 10 IG1D 2.436,2.787 2.816,2.926 0.380,0.139 10 AM21 2.341,2.078 2.142,2.747 false 3.139,2.067 3.184,2.779 false 2.726,2.069 2.683,2.782 false 1.556,3.055 1.904,3.197 0.348,0.142 10 SPDI 2.94,2.787 3.360,2.929 0.420,0.142 10 ACCD

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L5-29 (ABFS) - A21-2 (+B2) Power switch off 10 kΩ or higher
L5-29 (ABFS) - A22-5 (+B1) Power switch off 10 kΩ or higher
L5-29 (ABFS) - L5-1 (AM22) Power switch off 10 kΩ or higher
L5-29 (ABFS) - L6-7 (AM21) Power switch off 10 kΩ or higher
L5-29 (ABFS) - A22-6 (MREL) Power switch off 10 kΩ or higher
L5-29 (ABFS) - A22-1 (IG2) Power switch off 10 kΩ or higher
L5-29 (ABFS) - L6-1 (ACCD) Power switch off 10 kΩ or higher
L5-29 (ABFS) - L6-2 (IG1D) Power switch off 10 kΩ or higher
L5-29 (ABFS) - A22-2 (IG2D) Power switch off 10 kΩ or higher
L5-29 (ABFS) - L5-14 (SPDI) Power switch off 10 kΩ or higher
L5-29 (ABFS) - A21-16 (GI) Power switch off 10 kΩ or higher
L5-29 (ABFS) - A21-4 (FCTL) Power switch off 10 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)


e.

Reconnect the A21, A22, L5 and L6 power management control ECU connectors.


f.

Reconnect the L16 airbag ECU assembly connector.


g.

Install the IGCT NO. 2 fuse and AM2 fuse.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR