Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM › 2014.11–2016.05
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301574 HYBRID BATTERY SYSTEM D

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  DIAGNOSIS SYSTEM  


DESCRIPTION (w/o Multi-information Display)


a.

The power management control ECU has a self-diagnosis system. If the computer, hybrid control system, or a component is not working properly, the ECU records the conditions that relate to the fault. The ECU also illuminates the HV system warning light in the combination meter sub-assembly.

D105403E05
1.875,0.948 1.979,0.344 1.979,0.344 2.104,0.344 false 4.427,0.958 4.552,0.333 4.552,0.333 4.656,0.333 false 4.823,0.948 4.938,0.323 4.938,0.323 5.052,0.323 false 5.479,0.948 5.563,0.333 5.563,0.333 5.677,0.333 false 6.333,1.25 6.438,0.573 6.438,0.573 6.542,0.573 false 6.552,1.625 6.781,1.625 false 2.135,0.25 2.396,0.427 0.26,0.177 10 false *a 6.573,0.49 6.802,0.667 0.229,0.177 10 false *b 4.698,0.25 4.927,0.427 0.229,0.177 10 false *c 5.083,0.25 5.313,0.427 0.229,0.177 10 false *d 5.708,0.25 5.938,0.427 0.229,0.177 10 false *e 6.813,1.552 7.042,1.729 0.229,0.177 10 false *f

Text in Illustration
*a READY Light *b Hybrid Battery Indicator Light
*c Auxiliary Battery Charging Warning Light *d MIL
*e Hybrid System Overheat Warning Light *f HV System Warning Light

HINT:

The HV system warning light will illuminate when the hybrid vehicle control system malfunctions and the light will blink when in inspection mode.




DESCRIPTION (w/ Multi-information Display)


a.

The power management control ECU has a self-diagnosis system. If the computer, hybrid control system, or a component is not working properly, the ECU records the conditions that relate to the fault. The ECU also illuminates the master warning light in the combination meter sub-assembly.

A339407E02
2.073,1.063 2.208,0.479 2.208,0.479 2.313,0.479 true 4.01,1.104 4.156,0.521 4.156,0.521 4.26,0.521 true 5.115,0.979 5.25,0.396 5.25,0.396 5.354,0.396 true 6.302,1.521 6.531,0.729 6.531,0.729 6.698,0.729 true 6.302,1.75 6.542,2.396 6.542,2.396 6.708,2.396 true 2.354,0.385 2.615,0.563 0.26,0.177 10 false *a 4.302,0.448 4.531,0.625 0.229,0.177 10 false *b 5.385,0.313 5.615,0.49 0.229,0.177 10 false *c 6.719,0.656 6.948,0.833 0.229,0.177 10 false *d 6.729,2.302 6.958,2.479 0.229,0.177 10 false *e

Text in Illustration
*a READY Light *b Multi-information Display
*c Master Warning Light *d MIL
*e Auxiliary Battery Charging Warning Light - -

HINT:

The master warning light will illuminate when the hybrid vehicle control system malfunctions and the light will blink when in inspection mode.




2 TRIP DETECTION LOGIC


When a malfunction is first detected, the malfunction is temporarily stored in the power management control ECU memory (1st trip). If the same malfunction is detected during the next drive cycle, the MIL is illuminated (2nd trip).



FREEZE FRAME DATA


The power management control ECU records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.



AUXILIARY BATTERY VOLTAGE


Standard Voltage:
Switch Condition Specified Condition
Power switch on (IG) 11 to 14 V


If voltage is below 11 V, replace or recharge the battery.

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).




MIL (Malfunction Indicator Lamp)


a.

The MIL is illuminated when the power switch is first turned on (IG), before the READY indicator comes on.


b.

When the READY indicator turns on, the MIL should turn off. If the MIL remains illuminated, the diagnosis system has detected a malfunction or abnormality in the system.

HINT:

If the MIL is not illuminated when the power switch is first turned on (IG), check the MIL circuit (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>MIL Circuit).