Home › Engine / Hybrid System › 2ZR-FXE (ENGINE CONTROL) › SFI SYSTEM › 2014.11–2016.05
RM2070E _51 Engine / Hybrid System _061905 2ZR-FXE ENGINE CONTROL _0301559 SFI SYSTEM J

2ZR-FXE ENGINE CONTROL  SFI SYSTEM  MIL Circuit  


DESCRIPTION

The MIL (Malfunction Indicator Lamp) is used to indicate vehicle malfunction detected by the ECM. When the power switch is turned on (IG), power is supplied to the MIL circuit, and the ECM provides the circuit ground which illuminates the MIL.

The MIL operation can be checked visually: When the power switch is turned on (IG), the MIL should illuminate and should then turn off after power switch is turned on (READY). If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the GTS.

WIRING DIAGRAM

A259027E01
6.205,4.115 6.504,4.271 0.299,0.156 10 A57 6.49,4.115 6.845,4.294 0.355,0.179 10 ECM 6.061,0.887 6.268,1.094 0.206,0.206 10 W 3.922,1.444 4.203,1.586 0.281,0.142 10 L27 3.922,1.593 5.120,2.004 1.198,0.411 10 Combination Meter Sub-assembly 3.486,1.122 3.804,1.287 0.318,0.165 10 MET 0.76,1.098 1.017,1.268 0.258,0.170 10 IG2 0.364,2.667 0.700,2.847 0.336,0.179 10 P/I 1 0.364,3.13 0.752,3.331 0.389,0.201 10 MAIN 0.483,3.84 1.042,4.172 0.559,0.332 10 Auxiliary Battery 1.563,3.918 1.871,4.088 0.309,0.170 10 A22 1.563,4.072 2.902,4.406 1.339,0.334 10 Power Management Control ECU 1.911,3.379 2.295,3.537 0.384,0.158 10 IG2D 2.316,3.293 2.505,3.482 0.189,0.189 10 2 1.646,1.62 1.901,1.776 0.255,0.156 10 IG2 5.816,0.887 6.004,1.046 0.188,0.158 10 36 2.947,0.792 3.110,0.955 0.163,0.163 10 4 2.9,0.965 3.098,1.134 0.198,0.170 10 1A 2.741,2.267 2.939,2.436 0.198,0.170 10 1A 0.976,2.267 1.174,2.436 0.198,0.170 10 1A 0.192,2.267 0.389,2.436 0.198,0.170 10 1C 2.54,2.264 2.696,2.433 0.156,0.170 10 2 0.481,2.264 0.637,2.433 0.156,0.170 10 1 1.28,2.264 1.435,2.433 0.156,0.170 10 3 1.271,2.488 2.733,2.671 1.461,0.184 10 No. 2 Integration Relay 4.027,1.052 4.282,1.208 0.255,0.156 10 IG+ 4.736,1.052 4.991,1.208 0.255,0.156 10 EFI 3.879,0.887 4.071,1.043 0.192,0.156 10 2 5.011,0.887 5.203,1.043 0.192,0.156 10 6

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK THAT MIL IS ILLUMINATED
a.

Turn the power switch on (IG).


b.

Check the illumination of the MIL.

Result
Condition Proceed to
MIL remains illuminated A
MIL remains off B
MIL illuminates and should turn off after power switch is turned on (READY) C



A

2.CHECK WHETHER MIL TURNS OFF

B

5.CHECK THAT ENGINE STARTS

C

2.CHECK WHETHER MIL TURNS OFF
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Check if any DTCs have been stored. Note down the DTCs.



g.

Check if the MIL goes off.

OK:

MIL goes off.




OK

NG

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
a.

Disconnect the A57 ECM connector.


b.

Turn the power switch on (IG).


c.

Check that the MIL is not illuminated.

OK:

MIL is not illuminated.




OK

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - ECM)
4.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - ECM)
a.

Disconnect the combination meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L27-6 (EFI) or A57-36 (W) - Body ground Always 10 kΩ or higher


Result
Result Proceed to
NG A
OK (w/ Multi-information Display) B
OK (w/o Multi-information Display) C



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

REPLACE COMBINATION METER SUB-ASSEMBLY

C

5.CHECK THAT ENGINE STARTS
a.

Turn the power switch on (IG).


b.

Turn the GTS on.


c.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


d.

Start the engine.

Result:
Result Proceed to
Engine starts A
Engine cannot be put in inspection mode*
(Engine cannot start)
B


HINT:

*: The GTS cannot communicate with the ECM.




A

6.CHECK HARNESS AND CONNECTOR (ECM TERMINAL VOLTAGE)

B

6.CHECK HARNESS AND CONNECTOR (ECM TERMINAL VOLTAGE)
a.

Disconnect the ECM connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A57-36 (W) - Body ground Power switch on (IG) 11 to 14 V




OK

NG

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - ECM)
7.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - ECM)
a.

Disconnect the combination meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L27-6 (EFI) - A57-36 (W) Always Below 1 Ω


Result
Result Proceed to
NG A
OK (w/ Multi-information Display) B
OK (w/o Multi-information Display) C



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

REPLACE COMBINATION METER SUB-ASSEMBLY

C