Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM › 2014.11–2016.05
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301574 HYBRID BATTERY SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  U029A-123  Lost Communication with Hybrid Battery Pack Sensor Module  


DESCRIPTION

The battery smart unit detects the HV battery conditions (voltage, current, and temperature) and the battery cooling fan voltage, and sends the detected signals to the power management control ECU via serial communication. (The power management control ECU does not send signals to the battery smart unit.)

DTC No. INF Code DTC Detection Condition Trouble Area
U029A 123 Serial communication error between the battery smart unit and the power management control ECU (The power management control ECU did not receive signals from the battery smart unit.) (1 trip detection)
·

Wire harness or connector

·

Power management control ECU

·

Battery smart unit



WIRING DIAGRAM

A280982E03
0.521,0.979 0.906,1.135 0.385,0.156 10 false IGCT 2.677,1.458 3.083,1.625 0.406,0.167 10 false IGCT 4.063,0.979 4.854,1.135 0.792,0.156 10 false IGCT No. 2 2.406,0.729 2.552,0.896 0.146,0.167 10 false 3 2.406,1.094 2.552,1.26 0.146,0.167 10 false 2 3.146,1.094 3.292,1.26 0.146,0.167 10 false 1 3.146,0.719 3.292,0.885 0.146,0.167 10 false 5 4.594,0.719 4.74,0.885 0.146,0.167 10 false 2 4.135,0.719 4.281,0.885 0.146,0.167 10 false 1 5.885,0.708 6.031,0.875 0.146,0.167 10 false 5 5.875,3.833 6.021,4 0.146,0.167 10 false 2 6.083,0.813 6.469,0.99 0.385,0.177 10 false IGCT 6.073,3.917 6.479,4.146 0.406,0.229 10 false BTH+ 6.073,4.354 6.448,4.583 0.375,0.229 10 false BTH- 5.875,4.26 6.021,4.427 0.146,0.167 10 false 3 6.063,6.344 6.438,6.573 0.375,0.229 10 false GND 5.875,6.26 6.021,6.427 0.146,0.167 10 false 4 3.667,3.927 4.052,4.094 0.385,0.167 10 false BTH+ 3.698,4.375 4.052,4.531 0.354,0.156 10 false BTH- 4.198,3.948 4.406,4.094 0.208,0.146 10 false L5 4.208,4.198 4.458,4.365 0.25,0.167 10 false 33 4.208,3.75 4.458,3.917 0.25,0.167 10 false 32 3.646,2.135 4.052,2.365 0.406,0.229 10 false MREL 3.781,2.698 4.063,2.844 0.281,0.146 10 false +B1 3.76,3.219 4.063,3.396 0.302,0.177 10 false +B2 2.938,2.177 3.344,2.406 0.406,0.229 10 false AM22 2.927,2.74 3.333,2.917 0.406,0.177 10 false AM21 0.531,2.885 0.938,3.115 0.406,0.229 10 false AM2 4.156,3.24 4.563,3.469 0.406,0.229 10 false A21 4.156,2.719 4.563,2.948 0.406,0.229 10 false A22 4.229,1.938 4.375,2.104 0.146,0.167 10 false 6 4.24,2.51 4.385,2.677 0.146,0.167 10 false 5 4.24,3.042 4.385,3.208 0.146,0.167 10 false 2 2.854,6.969 4.083,7.354 1.229,0.385 10 false Power Management Control ECU 5.552,6.979 5.938,7.177 0.385,0.198 10 false L144 5.927,6.979 7.094,7.177 1.167,0.198 10 false Battery Smart Unit 4.208,4.385 4.427,4.552 0.219,0.167 10 false L5 4.219,6.438 4.427,6.583 0.208,0.146 10 false L5 3.802,6.448 4.083,6.615 0.281,0.167 10 false E01 4.26,6.25 4.406,6.417 0.146,0.167 10 false 5 4.146,2.146 4.552,2.375 0.406,0.229 10 false A22 0.833,5.229 2.021,5.583 1.188,0.354 10 false Combination Meter Sub-assembly 0.958,5.917 2.083,6.156 1.125,0.24 10 false BATT FAN Relay 1.698,6.448 2.073,6.625 0.375,0.177 10 false ECM 1.313,4.313 2.052,4.552 0.74,0.24 10 false ACC Relay 1.01,4.844 2.115,5.083 1.104,0.24 10 false IG1 No. 1 Relay 2.531,5.927 2.833,6.104 0.302,0.177 10 false A21 2.531,6.448 2.823,6.625 0.292,0.177 10 false A21 2.583,5.375 2.854,5.531 0.271,0.156 10 false L5 2.583,4.854 2.865,5.01 0.281,0.156 10 false L6 2.625,5.719 2.771,5.885 0.146,0.167 10 false 4 2.583,6.25 2.813,6.417 0.229,0.167 10 false 16 2.625,4.656 2.771,4.823 0.146,0.167 10 false 2 2.583,5.177 2.833,5.344 0.25,0.167 10 false 14 1.385,3.76 2.083,3.99 0.698,0.229 10 false IG2 Relay 2.938,4.323 3.375,4.49 0.438,0.167 10 false ACCD 2.948,4.844 3.313,5 0.365,0.156 10 false IG1D 2.927,6.448 3.177,6.677 0.25,0.229 10 false GI 2.927,5.375 3.292,5.542 0.365,0.167 10 false SPDI 2.938,5.906 3.323,6.073 0.385,0.167 10 false FCTL 0.427,0.604 1.094,0.76 0.667,0.156 10 false HV BATT 2.927,3.802 3.292,3.958 0.365,0.156 10 false IG2D 2.938,3.25 3.229,3.417 0.292,0.167 10 false IG2 2.573,4.333 2.854,4.49 0.281,0.156 10 false L6 2.625,4.125 2.771,4.292 0.146,0.167 10 false 1 2.531,3.24 2.833,3.417 0.302,0.177 10 false A22 2.531,3.781 2.823,3.958 0.292,0.177 10 false A22 2.635,3.021 2.781,3.188 0.146,0.167 10 false 1 2.635,3.583 2.865,3.75 0.229,0.167 10 false 2 2.583,2.74 2.865,2.896 0.281,0.156 10 false L6 2.625,2.521 2.771,2.688 0.146,0.167 10 false 7 2.583,2.177 2.865,2.333 0.281,0.156 10 false L5 2.625,1.958 2.771,2.125 0.146,0.167 10 false 1 1.396,3.208 2.094,3.438 0.698,0.229 10 false IG2 Relay 5.885,0.323 6.031,0.49 0.146,0.167 10 false 1 6.094,0.438 6.302,0.615 0.208,0.177 10 false B

CAUTION / NOTICE / HINT

CAUTION:
·

If the battery cover is removed, install it before turning the power switch on (IG) or (READY). If the power switch is turned on (IG) or (READY) with the battery cover removed, U029A-123 may be stored.

·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:

After the repair, clear the DTCs, turn the power switch on (IG), wait for 1 minute or more and check for DTCs.


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check for DTCs (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
Only U029A-123 is output. A
DTCs other than U029A-123 are also output. B



e.

Turn the power switch off.



A

2.CHECK HARNESS AND CONNECTOR (B AND IGCT VOLTAGE)

B

2.CHECK HARNESS AND CONNECTOR (B AND IGCT VOLTAGE)
NOTICE:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid battery shield sub-assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL).


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG).

NOTICE:

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.



e.
U190628E02
1.604,0.823 1.073,0.396 true 1.958,0.865 2.49,0.438 true 1.958,1.021 2.49,1.385 true 1.625,0.198 1.99,0.354 0.365,0.156 10 false L144 0.833,0.198 1.188,0.354 0.354,0.156 10 false GND 0.177,0.156 0.438,0.313 0.26,0.156 10 false *a 2.49,0.229 2.625,0.385 0.135,0.156 10 false B 2.521,1.323 2.948,1.479 0.427,0.156 10 false IGCT

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L144-1 (B) - L144-4 (GND) Power switch off 8.6 V or more
L144-5 (IGCT) - L144-4 (GND) Power switch on (IG) 8.6 V or more


Text in Illustration
*a Component with harness connected
(Battery Smart Unit)

HINT:

As there might be an intermittent malfunction in the battery voltage sensor power source circuit, inspect the following even if the measured voltage is as specified:

·

Installation condition of fuse(s) (before removing fuse(s)) (IGCT circuit)

·

Fuse condition (before and after removing fuse(s)) (IGCT circuit)

·

Connection condition of connectors (IGCT circuit)

·

Wire harness condition (IGCT circuit)

·

Wire harness condition (GND circuit)




f.

Turn the power switch off.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal.


h.

Install the No. 1 hybrid battery shield sub-assembly.



OK

3.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BATTERY SMART UNIT)

NG

CHECK POWER SOURCE CIRCUIT (BATTERY VOLTAGE SENSOR)

3.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BATTERY SMART UNIT)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the L5 power management control ECU connector.

NOTICE:

Before disconnecting the connector, push in on the connector body to check that the connector is not loose or disconnected.



c.

Remove the No. 1 hybrid battery shield sub-assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL).


d.
U190662E02
2.5,0.521 2.854,0.677 0.354,0.156 10 false L144

Disconnect the L144 battery smart unit connector.

NOTICE:

Before disconnecting the connector, push in on the connector body to check that the connector is not loose or disconnected.



e.

Measure the resistance according to the value(s) in the table below.

A398192E01
2.583,1.25 3,1.5 0.417,0.25 4.25,1.25 4.667,1.5 0.417,0.25 1.688,2.104 2.042,1.844 false 2.677,2.094 2.094,1.844 false 4.573,1.76 4.885,1.646 false 4.771,2.167 5.01,1.656 false 5.625,2.135 5.135,1.656 false 0.427,0.167 0.74,0.365 0.313,0.198 10 false *a 4.094,0.146 4.406,0.344 0.313,0.198 10 false *b 2.708,1.292 3.021,1.49 0.313,0.198 10 false L5 4.302,1.292 4.719,1.479 0.417,0.188 10 false L144 2.75,2.052 3.188,2.26 0.438,0.208 10 false BTH+ 4.26,1.719 4.573,1.917 0.313,0.198 10 false GND 1.323,2.052 1.76,2.26 0.438,0.208 10 false BTH- 5.667,2.125 6.104,2.333 0.438,0.208 10 false BTH+ 4.479,2.177 4.917,2.385 0.438,0.208 10 false BTH-

Standard Resistance:
Tester Connection Condition Specified Condition
L5-32 (BTH+) - L144-2 (BTH+) Power switch off Below 1 Ω
L5-33 (BTH-) - L144-3 (BTH-) Power switch off Below 1 Ω
L144-4 (GND) - Body ground Power switch off Below 1 Ω
L144-2 (BTH+) - L144-4 (GND) and Body ground Power switch off 10 kΩ or higher
L144-3 (BTH-) - L144-4 (GND) and Body ground Power switch off 10 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)
*b Rear view of wire harness connector
(to Battery Smart Unit)


f.
A252499E01
0.185,0.185 0.455,0.389 0.270,0.205 10 *1 0.614,0.907 0.885,1.111 0.270,0.205 10 *2 2.849,1.216 3.119,1.421 0.270,0.205 10 *3 1.679,1.266 0.788,1.005 false 2.014,1.598 2.836,1.312 false 2.849,1.697 3.119,1.902 0.270,0.205 10 *4 2.215,1.964 2.836,1.793 false

Remove the IGCT No. 2 fuse, HV BATT fuse and AM2 fuse from the engine room relay block and junction block assembly.

Text in Illustration
*1 Engine Room Relay Block and Junction Block Assembly
*2 AM2 Fuse
*3 HV BATT Fuse
*4 IGCT No. 2 Fuse


g.

Disconnect the A21, A22, L5 and L6 power management control ECU connectors.


h.

Measure the resistance according to the value(s) in the table below.

U154395E02
2.542,1.573 1.24,1.917 false 2.677,1.51 1.219,1.667 false 2.792,1.51 1.385,2.208 false 3.177,1.521 1.594,2.458 false 3.24,1.521 2.01,2.552 false 3.458,1.521 2.417,2.542 false 3.51,1.521 2.969,2.542 false 3.854,1.573 3.448,2.479 false 4.125,1.51 5.073,2.49 false 4.438,1.51 5.792,2.281 false 4.708,1.51 6.115,2.021 false 4.76,1.51 6.281,1.698 false 3.896,1.688 4.479,2.427 false 3.854,1.688 3.958,2.469 false 2.573,0.948 2.833,1.125 0.26,0.177 10 false A21 1.125,2.135 1.396,2.313 0.271,0.177 10 false +B2 1.063,1.865 1.25,2.042 0.188,0.177 10 false GI 1.771,2.552 2.042,2.729 0.271,0.177 10 false +B1 0.625,0.25 0.781,0.427 0.156,0.177 10 false *a 3.198,0.938 3.458,1.115 0.26,0.177 10 false A22 3.896,0.948 4.115,1.125 0.219,0.177 10 false L5 5.073,2.448 5.469,2.625 0.396,0.177 10 false AM22 5.833,2.271 6.229,2.448 0.396,0.177 10 false AM21 0.875,1.604 1.25,1.781 0.375,0.177 10 false FCTL 1.208,2.406 1.615,2.552 0.406,0.146 10 false MREL 2.854,2.552 3.125,2.708 0.271,0.156 10 false IG2 6.333,1.615 6.75,1.792 0.417,0.177 10 false ACCD 2.24,2.552 2.583,2.688 0.344,0.135 10 false IG2D 3.292,2.49 3.635,2.646 0.344,0.156 10 false SPDI 6.156,1.948 6.5,2.125 0.344,0.177 10 false IG1D 4.531,0.938 4.75,1.115 0.219,0.177 10 false L6 3.823,2.479 4.219,2.688 0.396,0.208 10 false BTH- 4.375,2.458 4.771,2.667 0.396,0.208 10 false BTH+

Standard Resistance:
Tester Connection Condition Specified Condition
L5-32 (BTH+) - L6-7 (AM21) Power switch off 10 kΩ or higher
L5-32 (BTH+) - L5-1 (AM22) Power switch off 10 kΩ or higher
L5-32 (BTH+) - A21-2 (+B2) Power switch off 10 kΩ or higher
L5-32 (BTH+) - A22-5 (+B1) Power switch off 10 kΩ or higher
L5-32 (BTH+) - A22-6 (MREL) Power switch off 10 kΩ or higher
L5-32 (BTH+) - A22-1 (IG2) Power switch off 10 kΩ or higher
L5-32 (BTH+) - L6-1 (ACCD) Power switch off 10 kΩ or higher
L5-32 (BTH+) L6-2 (IG1D) Power switch off 10 kΩ or higher
L5-32 (BTH+) - A22-2 (IG2D) Power switch off 10 kΩ or higher
L5-32 (BTH+) - A21-4 (FCTL) Power switch off 10 kΩ or higher
L5-32 (BTH+) - L5-14 (SPDI) Power switch off 10 kΩ or higher
L5-32 (BTH+) - A21-16 (GI) Power switch off 10 kΩ or higher
L5-33 (BTH-) - L6-7 (AM21) Power switch off 10 kΩ or higher
L5-33 (BTH-) - L5-1 (AM22) Power switch off 10 kΩ or higher
L5-33 (BTH-) - A21-2 (+B2) Power switch off 10 kΩ or higher
L5-33 (BTH-) - A22-5 (+B1) Power switch off 10 kΩ or higher
L5-33 (BTH-) - A22-6 (MREL) Power switch off 10 kΩ or higher
L5-33 (BTH-) - A22-1 (IG2) Power switch off 10 kΩ or higher
L5-33 (BTH-) - L6-1 (ACCD) Power switch off 10 kΩ or higher
L5-33 (BTH-) - L6-2 (IG1D) Power switch off 10 kΩ or higher
L5-33 (BTH-) - A22-2 (IG2D) Power switch off 10 kΩ or higher
L5-33 (BTH-) - L5-14 (SPDI) Power switch off 10 kΩ or higher
L5-33 (BTH-) - A21-4 (FCTL) Power switch off 10 kΩ or higher
L5-33 (BTH-) - A21-16 (GI) Power switch off 10 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)
- -


i.

Install the IGCT No. 2 fuse, HV BATT fuse and AM2 fuse.


j.

Reconnect the A21, A22, L5 and L6 power management control ECU connectors.


k.

Reconnect the L144 battery smart unit connector.


l.

Install the No. 1 hybrid battery shield sub-assembly.



OK

4.CHECK POWER MANAGEMENT CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK POWER MANAGEMENT CONTROL ECU
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid battery shield sub-assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL).


c.
U190663E02
2.469,0.51 2.802,0.667 0.333,0.156 10 false L144

Disconnect the L144 battery smart unit connector.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the power switch on (IG).

NOTICE:

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.



f.
U190649E02
1.271,1.375 0.875,1.625 true 1.531,1.333 1.896,1.031 true 1.406,1.333 1,1.021 true 0.177,0.094 0.365,0.333 0.188,0.24 10 false *a 0.656,1.635 1.156,1.885 0.5,0.25 10 false GND 1.927,1.271 2.281,1.438 0.354,0.167 10 false L144 1.948,0.917 2.448,1.167 0.5,0.25 10 false BTH+ 0.625,0.917 1.125,1.167 0.5,0.25 10 false BTH-

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L144-2 (BTH+) - L144-4 (GND) Power switch on (IG) 2.3 to 2.7 V
L144-3 (BTH-) - L144-4 (GND) Power switch on (IG) 2.3 to 2.7 V


Text in Illustration
*a Rear view of wire harness connector
(to Battery Smart Unit)


g.

Turn the power switch off.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L144-2 (BTH+) - L144-3 (BTH-) Power switch off 4.4 to 5.4 kΩ


HINT:

Resistance becomes 2.0 kΩ or less when there is a short circuit in the power management control ECU.



i.

Disconnect the cable from the negative (-) auxiliary battery terminal.


j.

Reconnect the L144 battery smart unit connector.


k.

Install the No. 1 hybrid battery shield sub-assembly.



OK

NG