Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM › from 2016.05
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301574 HYBRID BATTERY SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  P0A82-123  Hybrid Battery Pack Cooling Fan 1 Performance / Stuck OFF  


DESCRIPTION

Refer to the circuit description for DTC P0A84-123 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0A84-123).


DTC No. INF Code DTC Detection Condition Trouble Area
P0A82 123 The speed of the battery cooling blower assembly is not within the specified range (1 trip detection)
·

Battery cooling blower assembly

·

Battery smart unit

·

Hybrid vehicle control ECU

·

Intake duct

·

Wire harness or connector

·

Exhaust duct



HINT:

The above DTC can be stored while the battery cooling blower assembly operates. When performing a reproduction test, drive the vehicle until "Temp of batt TB1to6" is stored in the Freeze Frame Data and then start the battery cooling blower assembly. This DTC is not detected when performing an Active Test of "Driving the Battery Cooling Fan".


WIRING DIAGRAM

Refer to the wiring diagram for DTC P0A84-123 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0A84-123).

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

2.CHECK DUCT AND BLOWER
a.

Remove the console box assembly (See page Vehicle Interior>INTERIOR PANELS / TRIM>FRONT CONSOLE BOX>REMOVAL).


b.

Turn over the front floor carpet.


c.
A251033E02
2.298,3.1 2.482,3.253 0.184,0.154 10 *3 1.993,2.574 2.136,3.177 2.136,3.177 2.244,3.177 false 0.975,3.065 1.159,3.219 0.184,0.154 10 *5 0.673,2.557 0.812,3.142 0.812,3.142 0.921,3.142 false 1.318,2.653 1.503,2.806 0.184,0.154 10 *4 0.945,2.571 1.156,2.73 1.156,2.73 1.265,2.73 false 2.883,2.979 3.067,3.133 0.184,0.154 10 *2 3.054,1.965 3.239,2.119 0.184,0.154 10 *1 2.683,2.899 2.72,3.057 2.72,3.057 2.829,3.057 false 2.864,2.259 2.926,2.041 2.926,2.041 3.035,2.041 false

Check that the duct and battery cooling blower are not disconnected, damaged, or clogged with foreign matter, and that the acoustical materials have not peeled.

Text in Illustration
*1 Intake Duct
*2 Hybrid Cooling Blower Assembly
*3 No. 2 Intake Duct
*4 No. 4 Intake Duct
*5 Exhaust Duct

OK:

The duct and blower are not disconnected, damaged, or clogged with foreign matter and the acoustical materials have not peeled.



d.

Install the front floor carpet.


e.

Install the console box assembly.



OK

3.CHECK HARNESS AND CONNECTOR (BATTERY COOLING BLOWER - BATTERY SMART UNIT)

NG

CORRECT THE PROBLEM

3.CHECK HARNESS AND CONNECTOR (BATTERY COOLING BLOWER - BATTERY SMART UNIT)

OK

4.CHECK HARNESS AND CONNECTOR (BATTERY COOLING BLOWER - HYBRID VEHICLE CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (BATTERY COOLING BLOWER - HYBRID VEHICLE CONTROL ECU)

OK

5.CHECK HYBRID VEHICLE CONTROL ECU (GROUND SHORT CHECK)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HYBRID VEHICLE CONTROL ECU (GROUND SHORT CHECK)
a.

b.
U190588E02
2.573,1.031 2.292,0.302 2.292,0.302 2.219,0.302 false 1.885,1.031 1.771,0.313 1.771,0.313 1.708,0.313 false 2.615,1.25 2.906,0.323 2.906,0.323 3,0.323 false 1.417,0.219 1.74,0.365 0.323,0.146 10 false E01 1.938,0.219 2.344,0.458 0.406,0.24 10 false E02 3.042,0.25 3.354,0.5 0.313,0.25 10 false SI0 0.219,0.115 0.573,0.313 0.354,0.198 10 false *a 1.979,1.521 2.271,1.719 0.292,0.198 10 false L5 2.583,1.51 2.875,1.708 0.292,0.198 10 false L6

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L6-29 (SI0) - L5-5 (E01) Power switch off 10 kΩ or higher
L6-29 (SI0) - L6-5 (E02) Power switch off 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Hybrid Vehicle Control ECU)


c.

Install the hybrid vehicle control ECU.



OK

6.READ VALUE USING GTS (VMF FAN MOTOR VOLTAGE)

NG

6.READ VALUE USING GTS (VMF FAN MOTOR VOLTAGE)

A

7.CHECK BATTERY SMART UNIT

B

8.CHECK BATTERY SMART UNIT (VOLTAGE)