Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID VEHICLE CONTROL ECU › from 2016.05
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301592 HYBRID VEHICLE CONTROL ECU A

HYBRID / BATTERY CONTROL  HYBRID VEHICLE CONTROL ECU  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Before replacing the hybrid vehicle control ECU, refer to Service Bulletin.



Hide 2. WHEN REPLACING HYBRID VEHICLE CONTROL ECU

HV battery learning values are stored in the hybrid vehicle control ECU and ECM and are used to detect malfunctions and illuminate the hybrid battery indicator light in the combination meter assembly. When either of these ECUs is replaced, the new ECU receives the HV battery learning values from the other ECU and stores them.

NOTICE:
·

Do not replace the hybrid vehicle control ECU and ECM at the same time as the HV battery learning values will be lost. However, if it is necessary to replace both ECUs at the same time, replace them by following the procedure below.

·

Do not replace the hybrid vehicle control ECU or ECM with a used one from another vehicle.



a.

Procedure when replacing both hybrid vehicle control ECU and ECM:

i.

Disconnect the cable from the negative (-) auxiliary battery terminal.


ii.

Replace either ECU.


iii.

Connect the cable to the negative (-) auxiliary battery terminal.


iv.

Turn the power switch on (READY) and wait for 5 minutes or more.


v.

Turn the power switch off and disconnect the cable from the negative (-) auxiliary battery terminal.


vi.

Replace the other ECU.


vii.

Connect the cable to the negative (-) auxiliary battery terminal.


viii.

Check that the power switch can be turned on (READY).

HINT:

If the hybrid vehicle control ECU and ECM are replaced at the same time without following the above procedure, replace either of the ECUs with its original one and then replace it again by following the above procedure. If the correct procedure is not followed, perform the procedure again from the beginning.




Hide 8.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 55607 9.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 55550 10.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY

Hide 82877 11.REMOVE ECU INTEGRATION BOX RH (for LHD)

a.

Disconnect each connector.


b.
A379149

Disengage the 3 clamps.


c.

Remove the bolt, 2 nuts and ECU integration box RH.


Hide 82878 12.REMOVE ECU INTEGRATION BOX LH (for RHD)

a.

Disconnect each connector.


b.
A380667

Disengage the clamp.


c.

Remove the bolt, nut and ECU integration box LH.


Hide 89981C 13.REMOVE HYBRID VEHICLE CONTROL ECU (for LHD)

a.
A379150

Disengage the 2 claws and remove the hybrid vehicle control ECU as shown in the illustration.

NOTICE:
·

If the ECU integration box is deformed or damaged, replace it.

·

Do not bend the 2 claws more than necessary.




Hide 89981C 14.REMOVE HYBRID VEHICLE CONTROL ECU (for RHD)

a.
E190821

Disengage the 2 claws and remove the hybrid vehicle control ECU as shown in the illustration.

NOTICE:
·

If the ECU integration box is deformed or damaged, replace it.

·

Do not bend the 2 claws more than necessary.