Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › INVERTER CURRENT SENSOR
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301590 INVERTER CURRENT SENSOR A

HYBRID / BATTERY CONTROL  INVERTER CURRENT SENSOR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:

For the assembly procedure of the inverter with converter assembly, refer to the assembly procedure of the MG control computer with bracket sub-assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL COMPUTER>REASSEMBLY).


PROCEDURE

Hide 1.INSTALL INVERTER WIRE SUB-ASSEMBLY

NOTICE:
A330569E04
0.521,0.563 0.677,0.156 0.677,0.156 0.813,0.156 false 3.115,0.896 3.042,1.344 3.042,1.344 2.927,1.344 false 1.76,1.604 2.063,1.729 2.063,1.729 2.219,1.729 false 2.271,1.656 2.479,1.865 0.208,0.208 10 false *1 0.833,1.396 1.042,1.604 0.208,0.208 10 false *a 0.854,0.083 1.063,0.292 0.208,0.208 10 false *3 2.74,1.271 2.948,1.479 0.208,0.208 10 false *2

Compare the length of the wire harness from each interlock connector to the branching point. The interlock connector on the shorter side of the wire harness is referred to as the interlock connector (B).

Text in Illustration
*1 Branching Point (Connector A)
*2 Inter Lock Connector A
*3 Inter Lock Connector B
*a Shorter


a.
A330588E01
0.317,0.479 0.394,0.195 false 0.394,0.195 0.574,0.195 false 3.161,0.453 2.972,0.169 false 2.972,0.169 2.774,0.169 false 0.609,0.101 1.126,0.416 0.517,0.316 10 *1 2.572,0.066 2.791,0.264 0.218,0.198 10 *1

Apply protective tape to the inverter wire sub-assembly as shown in the illustration.

NOTICE:

Use non-residue type tape.


Text in Illustration
*1 Protective Tape


b.
A330582E04
1.698,1.083 2.094,0.885 2.094,0.885 2.5,0.885 false 1.146,4.135 1.438,4.427 1.438,4.427 1.615,4.427 false 1.646,4.344 1.875,4.552 0.229,0.208 10 false *1 2.573,0.802 2.802,1.01 0.229,0.208 10 false *2 0.792,2.75 1.021,2.958 0.229,0.208 10 false *a

Set the inverter terminal sub-assembly as shown in the illustration and confirm the installation position of the inverter wire sub-assembly.

Text in Illustration
*1 Connector A
*2 Clamp
*a Shorter


c.
A326165E01
1.434,2.274 1.795,1.561 false 1.795,1.561 2.027,1.561 false 1.228,2.266 1.692,1.381 false 1.692,1.381 1.829,1.381 false 0.635,0.934 0.91,0.264 false 0.91,0.264 1.09,0.264 false 1.163,0.16 1.423,0.358 0.260,0.198 10 *1 1.842,1.303 2.102,1.501 0.260,0.198 10 *2 2.057,1.467 2.317,1.664 0.260,0.198 10 *2

Engage the 2 claws to connect the interlock connector (B) to the inverter terminal sub-assembly as shown in the illustration.

HINT:

Push in the protruding part of the interlock connector (B) and make sure that it is securely installed.


Text in Illustration
*1 Inter Lock Connector B
*2 Claw


d.

Engage the wire harness of the inverter wire sub-assembly to the 6 clamps as shown in the illustration.

A326176

NOTICE:

Make sure that the wire which connects the interlock connectors is on the top of the other wires and not twisted.

A330572E04
6.625,1.854 6.729,2.427 6.729,2.427 6.854,2.427 false 0.573,1.813 0.885,2.563 0.885,2.563 1.094,2.563 false 1.135,2.49 1.521,2.729 0.385,0.24 10 false *2 6.885,2.344 7.135,2.594 0.25,0.25 10 false *1

Text in Illustration
*1 Inter Lock Connector A *2 Inter Lock Connector B



e.

Engage the 2 claws to connect the interlock connector (A) to the inverter terminal sub-assembly as shown in the illustration.

A326173E04
4.99,2.219 5.115,2.531 5.115,2.531 5.25,2.531 false 5.323,1.938 5.823,2.51 5.823,2.51 5.99,2.51 false 5.302,1.708 5.844,1.458 5.844,1.458 6,1.458 false 5.292,0.771 5.438,1.323 5.438,1.323 5.542,1.323 false 5.292,0.521 5.573,0.302 5.573,0.302 5.76,0.302 false 2.521,1.5 2.906,2.385 2.906,2.385 3.042,2.385 false 3.083,2.302 3.333,2.552 0.25,0.25 10 false *1 5.792,0.219 6.042,0.469 0.25,0.25 10 false *2 5.573,1.229 5.823,1.479 0.25,0.25 10 false *2 6.042,1.396 6.292,1.646 0.25,0.25 10 false *2 6.042,2.427 6.292,2.677 0.25,0.25 10 false *2 5.281,2.438 5.531,2.688 0.25,0.25 10 false *a 4.208,1.385 4.458,1.635 0.25,0.25 10 false *B 4.208,0.24 4.458,0.49 0.25,0.25 10 false *A

Text in Illustration
*A Type 1 *B Type 2
*1 Inter Lock Connector A *2 Claw
*a Terminal Tray - -

HINT:

Push in the protruding part of the interlock connector (A) and make sure that it is securely installed.



f.

Engage the wire harness of the inverter wire sub-assembly to each clamp to install it as shown in the illustration.

NOTICE:

Do not pull the wire harness excessively.


HINT:

The number of clamps used to engage the wire harnesses of the inverter wire sub-assembly varies depending on the part number of the inverter with converter assembly. Confirm the part number before performing work.


A326174E04
5.188,2.302 5.438,2.604 5.438,2.604 5.604,2.604 false 4.177,0.146 4.448,0.354 0.271,0.208 10 false *A 4.198,1.458 4.469,1.667 0.271,0.208 10 false *B 5.646,2.51 5.917,2.719 0.271,0.208 10 false *a

Text in Illustration
*A Type 1 *B Type 2
*a Terminal Tray - -


g.

Check the installation condition of the inverter wire sub-assembly.

NOTICE:

Make sure that the wire harness of inverter wire sub-assembly is not twisted.



Hide 2.INSTALL INVERTER CURRENT SENSOR SUB-ASSEMBLY

a.
A330565E01
2.293,1.301 2.697,1.919 false 2.697,1.919 2.903,1.919 false 2.242,2.074 2.568,2.521 false 2.568,2.521 2.792,2.521 false 2.912,1.816 3.158,2.063 0.246,0.246 12 *1 2.826,2.426 3.072,2.673 0.246,0.246 12 *2

Insert the bus-bars of the inverter terminal sub-assembly into the inverter current sensor sub-assembly as shown in the illustration.

Text in Illustration
*1 Bus-bar
*2 inverter current sensor sub-assembly


b.
A326170E01
0.13,0.119 0.460,0.413 0.330,0.295 10 *A 0.113,2.594 0.443,2.888 0.330,0.295 10 *B 2.614,3.591 2.734,2.826 false 2.734,2.826 3.172,2.826 false 2.837,3.591 2.958,2.826 false 3.201,2.731 3.380,2.917 0.179,0.186 10 *a

Install the inverter current sensor sub-assembly with the 2 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)

Text in Illustration
*A Type 1
*B Type 2
*a Terminal Tray


c.
A330209

Engage the wire harness of inverter current sensor sub-assembly to the 2 clamps as shown in the illustration.

HINT:
·

Although the number of clamps which the wire harnesses of the inverter current sensor sub-assembly are disengaged from during removal varies depending on the part number of the inverter with converter assembly, only 2 clamps will be used to engage the wire harness during installation.

·

The position of the connectors on the MG control computer with bracket sub-assembly side depend on the part number of the inverter with converter assembly.




d.

Remove the protective tape.

A330163E04
3.885,0.875 4.146,0.26 4.146,0.26 4.302,0.26 false 3.958,1.052 4.24,0.667 4.24,0.667 4.385,0.667 false 3.542,1.031 3.844,0.073 3.844,0.073 3.979,0.073 false 3.917,2.781 4.167,2.167 4.167,2.167 4.323,2.167 false 3.979,2.969 4.271,2.594 4.271,2.594 4.417,2.594 false 3.667,2.792 3.938,1.885 false 3.479,2.792 3.729,1.885 3.729,1.885 4.156,1.885 false 3.552,2.969 3.771,3.469 3.771,3.469 3.906,3.469 false 2.813,1.073 2.917,1.458 2.917,1.458 3.052,1.458 false 1.896,1.052 2.01,1.427 2.01,1.427 2.125,1.427 false 1.49,1.042 1.563,1.417 1.563,1.417 1.688,1.417 false 2.854,2.979 2.979,3.469 2.979,3.469 3.115,3.469 false 1.948,2.979 2.073,3.438 2.073,3.438 2.198,3.438 false 1.5,2.958 1.625,3.396 1.625,3.396 1.74,3.396 false 5.167,1.542 5.344,1.99 5.344,1.99 5.51,1.99 false 5.177,3.427 4.771,3.604 4.771,3.604 4.646,3.604 false 0.927,1.906 1.156,2.125 0.229,0.219 10 false *B 0.854,0.094 1.083,0.313 0.229,0.219 10 false *A 4.323,0.156 4.552,0.375 0.229,0.219 10 false *1 4.021,0 4.25,0.219 0.229,0.219 10 false *1 4.417,0.573 4.646,0.792 0.229,0.219 10 false *1 4.344,2.073 4.573,2.292 0.229,0.219 10 false *1 4.438,2.5 4.667,2.719 0.229,0.219 10 false *1 3.938,3.385 4.167,3.604 0.229,0.219 10 false *1 3.135,3.385 3.365,3.604 0.229,0.219 10 false *1 2.219,3.344 2.448,3.563 0.229,0.219 10 false *1 1.76,3.313 1.99,3.531 0.229,0.219 10 false *1 3.083,1.375 3.313,1.594 0.229,0.219 10 false *1 2.156,1.344 2.385,1.563 0.229,0.219 10 false *1 1.74,1.344 1.969,1.563 0.229,0.219 10 false *1 5.552,1.906 5.781,2.125 0.229,0.219 10 false *1 4.469,3.521 4.698,3.74 0.229,0.219 10 false *1 4.188,1.792 4.417,2.01 0.229,0.219 10 false *a

Text in Illustration
*A Type 1 *B Type 2
*1 Protective Tape - -
*a Terminal Tray - -