Home › Engine / Hybrid System › 2ZR-FXE (ENGINE MECHANICAL) › ENGINE UNIT
RM2070E _51 Engine / Hybrid System _061907 2ZR-FXE ENGINE MECHANICAL _0301599 ENGINE UNIT G

2ZR-FXE ENGINE MECHANICAL  ENGINE UNIT  INSPECTION  


PROCEDURE

Hide 13801 1.INSPECT NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.
A125485

Turn the roller by hand to check that it turns smoothly.

If the roller does not turn smoothly, replace the No. 1 valve rocker arm sub-assembly.


Hide 13750 2.INSPECT VALVE LASH ADJUSTER ASSEMBLY

NOTICE:
·

Keep the valve lash adjuster free from dirt and foreign matter.

·

Only use clean engine oil.



a.

Place the lash adjuster into a container filled with new engine oil.


b.

Insert the tip of SST into the lash adjuster plunger and use the tip to press down on the check ball inside the plunger.

A352260E01
1.115,2.604 1.115,3.01 false 2.906,2.615 2.906,3.021 false 1.167,2.458 1.938,2.552 false 2.188,2.542 2.896,2.438 false 2.188,2.135 2.802,2.052 false 1.271,2.083 1.958,2.146 false 1.375,1.677 1.958,1.771 false 2.198,1.76 2.708,1.635 false 1.365,1.458 1.948,1.385 false 2.188,1.385 2.698,1.365 false 2.26,0.969 2.646,0.979 false 1.458,0.979 1.875,0.979 false 4.583,0.979 5.083,1.719 false 1.115,0.427 1.427,0.625 0.313,0.198 10 false *a 2.906,0.385 3.219,0.583 0.313,0.198 10 false *b 1.938,0.906 2.583,1.125 0.646,0.219 10 false SST 2.01,1.313 2.323,1.51 0.313,0.198 10 false *c 2.021,1.698 2.333,1.896 0.313,0.198 10 false *1 2.01,2.063 2.323,2.26 0.313,0.198 10 false *3 2.01,2.479 2.323,2.677 0.313,0.198 10 false *2 1.052,3.073 1.375,3.281 0.323,0.208 10 false *4 2.844,3.042 3.156,3.24 0.313,0.198 10 false *4 4.26,0.906 4.906,1.125 0.646,0.219 10 false SST

Text in Illustration
*1 Plunger
*2 Check Ball
*3 Low Pressure Chamber
*4 High Pressure Chamber
*a CORRECT
*b INCORRECT
*c Taper Part

SST
09276-75010  


c.

Squeeze SST and the valve lash adjuster together to move the plunger up and down 5 to 6 times.


d.

Check the movement of the plunger and bleed the air.

OK:

Plunger moves up and down.


NOTICE:

When bleeding air from the high pressure chamber, make sure that the tip of SST is actually pressing the check ball as shown in the illustration. If the check ball is not pressed, air bleeding is not possible.



e.

After bleeding the air, remove SST. Then try to quickly and firmly press the plunger with your fingers.

OK:

Plunger is very difficult to move.


If the result is not as specified, replace the valve lash adjuster assembly.


Hide 13506 3.INSPECT CHAIN SUB-ASSEMBLY

a.
A162995E19
1.583,1.229 1.76,1.375 0.177,0.146 10 false *a 0.823,1.802 0.938,1.969 0.115,0.167 10 false 1 0.99,1.802 1.125,1.979 0.135,0.177 10 false 2 1.146,1.802 1.271,1.969 0.125,0.167 10 false 3 1.313,1.802 1.448,1.99 0.135,0.188 10 false 4 1.458,1.802 1.583,1.979 0.125,0.177 10 false 5 0.677,1.802 0.802,2 0.125,0.198 10 false 0 2.51,1.802 2.729,1.979 0.219,0.177 10 false 14 2.708,1.802 2.948,1.969 0.24,0.167 10 false 15

Pull the chain with a force of 147 N (15 kgf, 33.0 lbf) as shown in the illustration.

Text in Illustration
*a Measurement Length


b.

Using a vernier caliper, measure the length of 15 links.

Maximum chain elongation:

115.2 mm (4.54 in.)


NOTICE:

Perform the measurement at 3 random places. Use the average of the measurements.


If the average elongation is more than the maximum, replace the chain sub-assembly.


Hide 13507 4.INSPECT NO. 2 CHAIN SUB-ASSEMBLY

a.
A162995E19
1.583,1.229 1.76,1.375 0.177,0.146 10 false *a 0.823,1.802 0.938,1.969 0.115,0.167 10 false 1 0.99,1.802 1.125,1.979 0.135,0.177 10 false 2 1.146,1.802 1.271,1.969 0.125,0.167 10 false 3 1.313,1.802 1.448,1.99 0.135,0.188 10 false 4 1.458,1.802 1.583,1.979 0.125,0.177 10 false 5 0.677,1.802 0.802,2 0.125,0.198 10 false 0 2.51,1.802 2.729,1.979 0.219,0.177 10 false 14 2.708,1.802 2.948,1.969 0.24,0.167 10 false 15

Pull the chain with a force of 147 N (15 kgf, 33.0 lbf) as shown in the illustration.

Text in Illustration
*a Measurement Length


b.

Using a vernier caliper, measure the length of 15 links.

Maximum chain elongation:

102.1 mm (4.02 in.)


NOTICE:

Perform the measurement at 3 random places. Use the average of the measurements.


If the average elongation is more than the maximum, replace the No. 2 chain sub-assembly.


Hide 13519 5.INSPECT OIL PUMP DRIVE GEAR

a.
A053035

Place the chain around the oil pump drive gear.


b.

Using a vernier caliper, measure the diameter of the oil pump drive gear and chain.

Minimum gear diameter (with chain):

48.2 mm (1.90 in.)


NOTICE:

The vernier caliper must be in contact with the chain rollers when measuring.


If the diameter is less than the minimum, replace the chain and oil pump drive gear.


Hide 15163 6.INSPECT OIL PUMP DRIVE SHAFT GEAR

a.
A053036

Place the chain around the oil pump drive shaft gear.


b.

Using a vernier caliper, measure the diameter of the oil pump drive shaft gear and chain.

Minimum gear diameter (with chain):

48.2 mm (1.90 in.)


NOTICE:

The vernier caliper must be in contact with the chain rollers when measuring.


If the diameter is less than the minimum, replace the chain and oil pump drive shaft gear.


Hide 13050 7.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

a.
A063864

Place the chain around the camshaft timing gear assembly.


b.

Using a vernier caliper, measure the diameter of the camshaft timing gear assembly and chain.

Minimum gear diameter (with chain):

96.8 mm (3.81 in.)


NOTICE:

The vernier caliper must be in contact with the chain rollers when measuring.


If the diameter is less than the minimum, replace the chain and camshaft timing gear assembly.


Hide 13523G 8.INSPECT CAMSHAFT TIMING SPROCKET

a.
A053025

Place the chain around the camshaft timing sprocket.


b.

Using a vernier caliper, measure the diameter of the camshaft timing sprocket and chain.

Minimum gear diameter (with chain):

96.8 mm (3.81 in.)


NOTICE:

The vernier caliper must be in contact with the chain rollers when measuring.


If the diameter is less than the minimum, replace the chain and camshaft timing sprocket.


Hide 13521 9.INSPECT CRANKSHAFT TIMING GEAR

a.
A053035

Place the chain around the crankshaft timing gear.


b.

Using a vernier caliper, measure the diameter of the crankshaft timing gear and chain.

Minimum gear diameter (with chain):

51.1 mm (2.01 in.)


NOTICE:

The vernier caliper must be in contact with the chain rollers when measuring.


If the diameter is less than the minimum, replace the chain and crankshaft timing gear.


Hide 13559 10.INSPECT CHAIN TENSIONER SLIPPER

a.
A150912

Using a vernier caliper, measure the chain tensioner slipper wear.

Maximum wear:

1.0 mm (0.0394 in.)


If the wear is more than the maximum, replace the chain tensioner slipper.


Hide 13561 11.INSPECT NO. 1 CHAIN VIBRATION DAMPER

a.
A150913

Using a vernier caliper, measure the No. 1 chain vibration damper wear.

Maximum wear:

1.0 mm (0.0394 in.)


If the wear is more than the maximum, replace the No. 1 chain vibration damper.


Hide 13562 12.INSPECT NO. 2 CHAIN VIBRATION DAMPER

a.
A150914

Using a vernier caliper, measure the No. 2 chain vibration damper wear.

Maximum wear:

1.0 mm (0.0394 in.)


If the wear is more than the maximum, replace the No. 2 chain vibration damper.


Hide 13549 13.INSPECT CHAIN TENSIONER PLATE

a.
A126893

Using a vernier caliper, measure the chain tensioner plate wear.

Maximum wear:

1.0 mm (0.0394 in.)


If the wear is more than the maximum, replace the chain tensioner plate.


Hide 13540 14.INSPECT NO. 1 CHAIN TENSIONER

a.
A146263E03
0.767,0.54 0.931,0.696 0.163,0.156 10 *c 0.444,0.805 0.605,0.960 0.162,0.156 10 *b 1.254,1.432 1.418,1.588 0.164,0.156 10 *a

Check that the plunger moves smoothly when the cam is raised with your finger.

Text in Illustration
*a Lock
*b Move
*c Raise


b.

Release the cam, then check that the plunger is locked in place by the cam and does not move when pushing with your finger.

If necessary, replace the No. 1 chain tensioner.


Hide 13511 15.INSPECT CAMSHAFT

a.
EM01628

Inspect the camshaft for runout.

i.

Place the camshaft on V-blocks.


ii.

Using a dial indicator, measure the circle runout at the center journal.

Maximum circle runout:

0.04 mm (0.00157 in.)


If the circle runout is more than the maximum, replace the camshaft.



b.
A036687

Inspect the cam lobes.

i.

Using a micrometer, measure the cam lobe height.

Standard cam lobe height:

41.779 to 41.879 mm (1.6448 to 1.6488 in.)


Minimum cam lobe height:

41.629 mm (1.6389 in.)


If the cam lobe height is less than the minimum, replace the camshaft.



c.
A036688

Inspect the camshaft journals.

i.

Using a micrometer, measure the journal diameter.

Standard Journal Diameter:
Journal Position Specified Condition
No. 1 34.449 to 34.465 mm (1.3563 to 1.3569 in.)
Others 22.949 to 22.965 mm (0.90350 to 0.90413 in.)


If the journal diameter is not as specified, check the oil clearance (See page Engine / Hybrid System>2ZR-FXE (ENGINE MECHANICAL)>CYLINDER HEAD>INSPECTION).



Hide 13512 16.INSPECT NO. 2 CAMSHAFT

a.
EM01628

Inspect the No. 2 camshaft for runout.

i.

Place the No. 2 camshaft on V-blocks.


ii.

Using a dial indicator, measure the circle runout at the center journal.

Maximum circle runout:

0.04 mm (0.00157 in.)


If the circle runout is more than the maximum, replace the No. 2 camshaft.



b.
A036687

Inspect the cam lobes.

i.

Using a micrometer, measure the cam lobe height.

Standard cam lobe height:

43.346 to 43.446 mm (1.7065 to 1.7105 in.)


Minimum cam lobe height:

43.196 mm (1.7006 in.)


If the cam lobe height is less than the minimum, replace the No. 2 camshaft.



c.
A036688

Inspect the camshaft journals.

i.

Using a micrometer, measure the journal diameter.

Standard Journal Diameter:
Journal Position Specified Condition
No. 1 34.449 to 34.465 mm (1.3563 to 1.3569 in.)
Others 22.949 to 22.965 mm (0.90350 to 0.90413 in.)


If the journal diameter is not as specified, check the oil clearance (See page Engine / Hybrid System>2ZR-FXE (ENGINE MECHANICAL)>CYLINDER HEAD>INSPECTION).



Hide 11101A 17.INSPECT CYLINDER HEAD SET BOLT

a.
A209191E04
1.694,1.021 1.859,1.180 0.165,0.159 10 *a 2.114,1.628 2.294,1.780 0.180,0.152 10 *b 1.384,2.715 1.536,2.864 0.152,0.149 10 *c

Using a vernier caliper, measure the length of the cylinder head set bolt from the seat to the end.

Text in Illustration
*a Measurement Length
*b Measurement Area
*c Distance

Standard length:

146.8 to 148.2 mm (5.78 to 5.83 in.)


Maximum length:

149.2 mm (5.87 in.)


HINT:
·

If the length is greater than the maximum, replace the bolt with a new one. Failure to do so may lead to engine damage.

·

If there is any thread deformation, replace the bolt with a new one.




b.

Using a vernier caliper, measure the diameter of the threaded portion of the bolt at its thinnest point.

HINT:

Use a straightedge to determine the thinnest point of the threaded portion of the bolt.


Measurement point:

115 mm (4.53 in.)


Standard diameter:

9.77 to 9.96 mm (0.385 to 0.392 in.)


Minimum diameter:

9.4 mm (0.370 in.)


HINT:
·

If the diameter is less than the minimum, replace the cylinder head set bolt with a new one. Failure to do so may lead to engine damage.

·

If there is any thread deformation, replace the cylinder head set bolt with a new one.



HINT:

If a visual check reveals no excessively thin areas, check the center of the bolt (refer to illustration) and find the area that has the smallest diameter.



Hide 17141 18.INSPECT EXHAUST MANIFOLD

a.
A158847

Using a precision straightedge and feeler gauge, measure the warpage on the surface that contacts the cylinder head.

Maximum warpage:

0.7 mm (0.0276 in.)


If the warpage is more than the maximum, replace the exhaust manifold.