Home › Engine / Hybrid System › 2ZR-FXE (ENGINE MECHANICAL) › CYLINDER HEAD
RM2070E _51 Engine / Hybrid System _061907 2ZR-FXE ENGINE MECHANICAL _0301600 CYLINDER HEAD G

2ZR-FXE ENGINE MECHANICAL  CYLINDER HEAD  INSPECTION  


PROCEDURE

Hide 1.INSPECT CYLINDER HEAD FOR FLATNESS

a.

Using a precision straightedge and feeler gauge, measure the warpage of the contact surfaces where the cylinder head contacts the cylinder block and manifold.

A352266E01
0.938,2.115 1.25,2.313 0.313,0.198 10 false *a 3.969,1.469 4.281,1.667 0.313,0.198 10 false *b 4.021,2.625 4.333,2.823 0.313,0.198 10 false *c

Text in Illustration
*a Cylinder Head Lower Side:
*b Intake Manifold Side:
*c Exhaust Manifold Side:

Maximum Warpage:
Item Specified Condition
Cylinder block side 0.05 mm (0.00197 in.)
Intake manifold side 0.10 mm (0.00394 in.)
Exhaust manifold side 0.10 mm (0.00394 in.)


If the warpage is more than the maximum, replace the cylinder head.


Hide 2.INSPECT CYLINDER HEAD FOR CRACKS

a.
A150952

Using a dye penetrate, check the intake ports, exhaust ports and cylinder surface for cracks.

If cracked, replace the cylinder head.


Hide 3.INSPECT VALVE SEATS

a.
A146287E03
2.758,1.104 2.950,1.260 0.192,0.156 10 *a

Apply a light coat of Prussian blue to the valve face.

Text in Illustration
*a Width


b.

Lightly press the valve face against the valve seat.

HINT:

Do not rotate the valve while pressing the valve.



c.

Check the valve face and valve seat.

i.

Intake Side:

Check that the valve seat contacts the middle of the valve face with the width between 1.0 and 1.4 mm (0.0394 and 0.0551 in.).

If not, correct the valve seat.


ii.

Exhaust Side:

Check that the valve seat contacts the middle of the valve face with the width between 1.0 and 1.4 mm (0.0394 and 0.0551 in.).

If not, correct the valve seat.


iii.

Check that the contact surfaces of the valve seat and valve face are even around the entire valve seat.

If not, correct the valve seat.



Hide 4.INSPECT CAMSHAFT THRUST CLEARANCE


b.
A150953

Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.

Standard thrust clearance:

0.06 to 0.155 mm (0.00236 to 0.00610 in.)


Maximum thrust clearance:

0.17 mm (0.00669 in.)


If the thrust clearance is greater than the maximum, replace the camshaft housing. If the thrust surface is damaged, replace the camshaft.


Hide 5.INSPECT CAMSHAFT OIL CLEARANCE

a.

Clean the bearing caps and camshaft journals.


b.

Place the camshafts on the camshaft housing.


c.
A150965E06
0.948,0.177 1.063,0.177 1.063,0.177 1.781,1.01 false 0.76,0.094 0.927,0.271 0.167,0.177 10 false *1

Lay a strip of Plastigage across each of the camshaft journals.

Text in Illustration
*1 Plastigage


d.

Install the bearing caps (See page Engine / Hybrid System>2ZR-FXE (ENGINE MECHANICAL)>CAMSHAFT>INSTALLATION).

NOTICE:

Do not turn the camshaft.




f.
A150954E06
0.906,0.198 1.052,0.198 1.052,0.198 1.875,1.021 false 0.729,0.115 0.896,0.302 0.167,0.188 10 false *1

Measure the Plastigage at its widest point.

Text in Illustration
*1 Plastigage

Standard Oil Clearance:
Item Specified Condition
Camshaft No. 1 Journal 0.030 to 0.063 mm (0.00118 to 0.00248 in.)
Camshaft Other Journals 0.035 to 0.072 mm (0.00138 to 0.00283 in.)


Maximum Oil Clearance:
Item Specified Condition
Camshaft No. 1 Journal 0.085 mm (0.00335 in.)
Camshaft Other Journals 0.09 mm (0.00354 in.)


NOTICE:

Completely remove the Plastigage after the inspection.


If the oil clearance is more than the maximum, replace the camshaft. If necessary, replace the camshaft housing.


Hide 13711B 6.INSPECT COMPRESSION SPRING

HINT:

Type A and Type B can be distinguished by the shape of the compression spring.


A314486E01
1.71,0.062 1.945,0.251 0.235,0.189 12 *B 1.785,0.624 2.020,0.813 0.235,0.189 10 *1 1.981,0.651 2.088,0.484 false 1.8,0.851 2.035,1.040 0.235,0.189 10 *2 1.997,0.937 2.24,0.937 false 1.862,1.494 2.097,1.683 0.235,0.189 10 *3 2.058,1.579 2.302,1.579 false 1.945,2.739 2.180,2.928 0.235,0.189 10 *4 2.142,2.824 2.385,2.824 false 1.678,0.047 3.156,3.158 1.479,3.111 0.094,0.062 0.329,0.251 0.235,0.189 12 *A 0.17,0.624 0.405,0.813 0.235,0.189 10 *1 0.366,0.651 0.472,0.484 false 0.184,0.851 0.419,1.040 0.235,0.189 10 *2 0.381,0.937 0.625,0.937 false 0.263,1.494 0.498,1.683 0.235,0.189 10 *3 0.46,1.579 0.704,1.579 false 0.347,2.739 0.582,2.928 0.235,0.189 10 *4 0.543,2.824 0.787,2.824 false 0.062,0.047 1.541,3.158 1.479,3.111

Text in Illustration
*A Type A
*B Type B
*1 No. 1 Valve Rocker Arm Sub-assembly
*2 Valve Spring Retainer
*3 Compression Spring
*4 Valve Lash Adjuster Assembly

Type Compression Spring Shape
A Straight
B Tapered

a.

Type A:

i.
EM00801

Using a vernier caliper, measure the free length of the compression spring.

Standard free length:

53.87 mm (2.12 in.)


If the free length is not as specified, replace the compression spring.


ii.
A361772

Using a steel square, measure the deviation of the compression spring.

Maximum deviation:

1.0 mm (0.0394 in.)


If the deviation is more than the maximum, replace the compression spring.



b.

Type B:

i.
A314490

Using a vernier caliper, measure the free length of the compression spring.

Standard free length:

51.88 mm (2.042 in.) or 51.90 mm (2.043 in.)


If the free length is not as specified, replace the compression spring.


ii.
A319225E26
1.438,0.375 1.708,0.573 0.271,0.198 10 false *a 0.438,1.24 0.979,1.656 0.542,0.417 10 false 40 mm (1.57 in.)

Using a steel square, measure the deviation of the compression spring.

Text in Illustration
*a Deviation

Maximum deviation:

1.4 mm (0.0551 in.)


Maximum angle:

2°


If the deviation is more than the maximum, replace the compression spring.



Hide 13711 7.INSPECT INTAKE VALVE

a.
A121380E03
1.884,1.028 2.054,1.172 0.170,0.145 10 *a

Using a vernier caliper, measure the overall length of the valve.

Text in Illustration
*a Overall Length

Standard overall length:

109.34 mm (4.30 in.)


Minimum overall length:

108.84 mm (4.29 in.)


If the overall length is less than the minimum, replace the valve.


b.
A121378

Using a micrometer, measure the diameter of the valve stem.

Standard valve stem diameter:

5.470 to 5.485 mm (0.215 to 0.216 in.)


If the valve stem diameter is not as specified, check the oil clearance.


c.
A379392E01
0.74,1.469 1.052,1.667 0.313,0.198 10 false *a

Using a vernier caliper, measure the valve head margin thickness.

Text in Illustration
*a Margin Thickness

Standard margin thickness:

1.0 mm (0.0394 in.)


Minimum margin thickness:

0.5 mm (0.0197 in.)


If the margin thickness is less than the minimum, replace the valve.


Hide 13715 8.INSPECT EXHAUST VALVE

a.
A121383E03
1.932,0.968 2.106,1.133 0.174,0.165 10 *a

Using a vernier caliper, measure the overall length of the valve.

Text in Illustration
*a Overall Length

Standard overall length:

108.25 mm (4.26 in.)


Minimum overall length:

107.75 mm (4.24 in.)


If the overall length is less than the minimum, replace the valve.


b.
A121381

Using a micrometer, measure the diameter of the valve stem.

Standard valve stem diameter:

5.465 to 5.480 mm (0.215 to 0.216 in.)


If the valve stem diameter is not as specified, check the oil clearance.


c.
A121382E03
0.613,1.323 0.769,1.492 0.156,0.169 10 *a

Using a vernier caliper, measure the valve head margin thickness.

Text in Illustration
*a Margin Thickness

Standard margin thickness:

1.0 mm (0.0394 in.)


Minimum margin thickness:

0.5 mm (0.0197 in.)


If the margin thickness is less than the minimum, replace the valve.


Hide 9.INSPECT VALVE GUIDE BUSH OIL CLEARANCE

a.
A150966

Using a caliper gauge, measure the inside diameter of the guide bush.

Standard bushing inside diameter:

5.510 to 5.530 mm (0.217 to 0.218 in.)



b.

Subtract the valve stem diameter measurement from the guide bush inside diameter measurement.

Standard Oil Clearance:
Item Specified Condition
Intake 0.025 to 0.060 mm (0.000984 to 0.00236 in.)
Exhaust 0.030 to 0.065 mm (0.00118 to 0.00256 in.)


Maximum Oil Clearance:
Item Specified Condition
Intake 0.080 mm (0.00315 in.)
Exhaust 0.085 mm (0.00335 in.)


If the clearance is more than the maximum, replace the valve and guide bush.