Home › Engine / Hybrid System › 2ZR-FXE (ENGINE MECHANICAL) › CAMSHAFT › 2012.03–2012.10
RM2070E _51 Engine / Hybrid System _061907 2ZR-FXE ENGINE MECHANICAL _0301594 CAMSHAFT A

2ZR-FXE ENGINE MECHANICAL  CAMSHAFT  REMOVAL  


PROCEDURE

Hide 1.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

Hide 11409 5.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 25620 7.REMOVE EGR VALVE WITH COOLER ASSEMBLY

Hide 23807 10.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

Hide 23807V 11.REMOVE NO. 1 DELIVERY PIPE SPACER

Hide 23250 12.REMOVE FUEL INJECTOR ASSEMBLY

Hide 11201 14.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 17.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.
A408421C01
0.24,1.25 1.333,1.25 1.333,1.25 1.354,1.885 true 0.552,1.938 0.552,1.26 true 0.844,2.802 0.76,2.323 0.76,2.323 0.583,2.323 true 0.375,3.563 0.563,3.563 0.563,3.563 0.74,2.969 true 1.677,2.333 1.51,2.333 1.51,2.333 0.875,1.615 true 0.083,1.177 0.396,1.375 0.313,0.198 10 false *d 0.417,2.26 0.729,2.458 0.313,0.198 10 false *a 0.208,3.469 0.521,3.667 0.313,0.198 10 false *b 1.719,2.271 2.031,2.469 0.313,0.198 10 false *c
*a Timing Mark
*b Timing Notch
*c Timing Mark (Rectangle)
*d Mark (Circle)


Turn the crankshaft pulley until its notch and timing mark "0" of the timing chain cover are aligned.

NOTICE:

There are 3 marks on the camshaft timing sprocket. Make sure that the timing mark (rectangle) is at the top.



b.

Check that the timing marks on both the camshaft timing sprocket and the camshaft timing gear are facing upward as shown in the illustration.

If not, turn the crankshaft 1 complete revolution (360°) and align the marks as above.


Hide 13540 19.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A214916

Remove the 2 nuts, bracket, chain tensioner and gasket.

NOTICE:

Do not turn the crankshaft without the No. 1 chain tensioner installed.



Hide 11302 20.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

Hide 13559 22.REMOVE CHAIN TENSIONER SLIPPER

a.
A214929

Remove the chain tensioner slipper from the cylinder block.


Hide 13561 23.REMOVE NO. 1 CHAIN VIBRATION DAMPER

a.
A214930

Remove the 2 bolts and chain vibration damper.


Hide 13562 24.REMOVE NO. 2 CHAIN VIBRATION DAMPER

a.
A214931

Remove the 2 bolts and No. 2 chain vibration damper.


Hide 13506 25.REMOVE CHAIN SUB-ASSEMBLY

a.
A214932

Hold the hexagonal portion of the camshaft with a wrench and turn the camshaft timing gear counterclockwise to loosen the chain between the camshaft timing gears.


b.

With the chain loosened, release the chain from the camshaft timing gear and place it on the camshaft timing gear.

HINT:

Be sure to release the chain from the sprocket completely.



c.

Turn the camshaft clockwise to return it to the original position and remove the chain.


Hide 13050 26.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

a.

Inspect the lock of the camshaft timing gear.


b.
A214933E05
1.969,0.125 2.031,0.125 2.031,0.125 2.458,0.469 true 1.323,0.583 1.417,0.583 1.417,0.583 1.49,0.99 true 1.854,1.323 1.781,1.323 1.781,1.323 1.521,1.094 false 3.198,1.063 3.073,1.063 3.073,1.063 2.719,0.708 true 1.802,0.042 1.979,0.219 0.177,0.177 10 true *a 1.156,0.49 1.313,0.667 0.156,0.177 10 true *1 3.198,0.969 3.354,1.146 0.156,0.177 10 false *b 1.875,1.24 2.031,1.417 0.156,0.177 10 true *b

After cleaning and degreasing the VVT oil hole on the intake side of the No. 1 camshaft bearing cap, completely seal the oil hole with adhesive tape or equivalent as shown in the illustration to prevent air from leaking.

Text in Illustration
*1 Adhesive Tape
*a Adhesive Tape Sealing Area
*b Prick a Hole

NOTICE:

Be sure to cover the oil hole completely because air leaks due to insufficient sealing will prevent the lock pin from being released.



c.

Prick a hole in the tape covering the oil hole as shown in the illustration. (Procedure A)


d.
A214934

Apply approximately 150 kPa (1.5 kgf/cm2, 22 psi) of air pressure to the hole pricked in procedure A to release the lock pin.

NOTICE:
·

If air leaks out, reattach the adhesive tape.

·

Cover the oil hole with a piece of cloth when applying air pressure to prevent oil from spraying.




e.

Forcibly turn the camshaft timing gear in the advance direction (counterclockwise).

HINT:

Depending on the air pressure applied, the camshaft timing gear may turn in the advance direction without assistance.



f.
A214935

Turn the camshaft timing gear within its movable range (26.5 to 28.5°) 2 or 3 times without turning it to the most retarded position. Make sure that the camshaft timing gear turns smoothly.


g.

Remove the adhesive tape from the No. 1 camshaft bearing cap.


Hide 13050 27.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

a.
A214936

Remove the flange bolt while holding the hexagonal portion of the camshaft with a wrench, and then remove the camshaft timing gear.

Text in Illustration
*1 Flange Bolt
*a Do not remove

NOTICE:
·

Before removing the camshaft timing gear, make sure that the lock pin has been released.

·
A162976E04
1.741,1.762 1.920,1.929 0.179,0.168 10 *a 0.381,1.759 0.564,1.907 0.183,0.149 10 *1 1.176,1.583 1.711,1.779 1.711,1.779 1.317,1.398 false 0.488,1.422 0.488,1.741 false 0.935,1.229 1.711,1.779 1.711,1.779 1.11,0.985 false

Be sure not to remove the other 4 bolts.

·

Keep the camshaft timing gear horizontal while removing it from the camshaft.




Hide 13523G 28.REMOVE CAMSHAFT TIMING SPROCKET

a.
A214937

Remove the flange bolt while holding the hexagonal portion of the camshaft with a wrench, and then remove the camshaft timing sprocket.


Hide 29.REMOVE CAMSHAFT BEARING CAP

a.
A214938E05
0.719,0.458 0.823,0.615 0.104,0.156 10 true 1 0.719,1.042 0.823,1.198 0.104,0.156 10 true 2 3.115,0.448 3.219,0.604 0.104,0.156 10 true 3 1.375,1.073 1.479,1.229 0.104,0.156 10 true 6 3.115,1.094 3.219,1.25 0.104,0.156 10 true 4 2.521,0.458 2.625,0.615 0.104,0.156 10 true 7 1.375,0.406 1.479,0.563 0.104,0.156 10 true 5 2.542,1.052 2.646,1.208 0.104,0.156 10 true 8 1.938,0.375 2.042,0.531 0.104,0.156 10 true 9 1.958,1.052 2.156,1.198 0.198,0.146 10 true 10

Uniformly loosen and remove the 10 bearing cap bolts in the sequence shown in the illustration.


b.
A214939E05
0.052,1.771 0.156,1.927 0.104,0.156 10 false 1 2.531,1.635 2.719,1.781 0.188,0.146 10 true 10 0.094,0.073 0.198,0.229 0.104,0.156 10 false 2 0.063,0.74 0.167,0.896 0.104,0.156 10 false 3 3.104,1.656 3.208,1.813 0.104,0.156 10 true 4 3.073,0.146 3.177,0.302 0.104,0.156 10 false 5 3.094,0.792 3.198,0.948 0.104,0.156 10 true 6 0.708,1.625 0.813,1.781 0.104,0.156 10 true 7 0.729,0.115 0.833,0.271 0.104,0.156 10 true 8 0.698,0.823 0.802,0.979 0.104,0.156 10 true 9 2.51,0.167 2.698,0.313 0.188,0.146 10 true 11 2.5,0.813 2.688,0.958 0.188,0.146 10 true 12 1.938,1.604 2.125,1.75 0.188,0.146 10 true 13 1.927,0.135 2.115,0.281 0.188,0.146 10 true 14 1.927,0.802 2.115,0.948 0.188,0.146 10 true 15

Uniformly loosen and remove the 15 bearing cap bolts in the sequence shown in the illustration.

NOTICE:

Uniformly loosen the bearing cap bolts while keeping the camshaft housing level.



c.

Remove the 5 bearing caps.

HINT:

Arrange the removed parts in the correct order.



Hide 13511 30.REMOVE CAMSHAFT

a.
A214940

Remove the camshaft.


Hide 13512 31.REMOVE NO. 2 CAMSHAFT

a.
A214941

Remove the No. 2 camshaft.


Hide 11811 32.REMOVE NO. 1 CAMSHAFT BEARING

a.
A214943

Remove the 2 No. 1 camshaft bearings.


Hide 11821 33.REMOVE NO. 2 CAMSHAFT BEARING

a.
A216079

Remove the 2 No. 2 camshaft bearings.


Hide 11103 34.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY

a.
A150889

Remove the 2 bolts.


b.
A150888E02
1.414,3.962 1.592,4.118 0.178,0.156 10 *1 0.701,2.584 1.503,3.931 1.503,3.931 1.877,3.185 false

Remove the camshaft housing by prying between the cylinder head and camshaft housing with a screwdriver.

Text in Illustration
*1 Protective Tape

NOTICE:

Be careful not to damage the contact surfaces of the cylinder head and camshaft housing.


HINT:

Tape the screwdriver tip before use.