Home › Engine / Hybrid System › 2ZR-FXE (ENGINE MECHANICAL) › CYLINDER BLOCK
RM2070E _51 Engine / Hybrid System _061907 2ZR-FXE ENGINE MECHANICAL _0301601 CYLINDER BLOCK G

2ZR-FXE ENGINE MECHANICAL  CYLINDER BLOCK  INSPECTION  


PROCEDURE

Hide 1.INSPECT CYLINDER BLOCK FOR WARPAGE

a.
A151003

Using a straightedge and feeler gauge, measure the warpage of the surface that contacts the cylinder head gasket.

Maximum warpage:

0.05 mm (0.00197 in.)


If the warpage is more than the maximum, replace the cylinder block.


Hide 2.INSPECT CYLINDER BORE

a.
A169057E19
2.01,2.5 1.906,2.5 1.906,2.5 1.719,2.896 false 1.625,3.031 1.458,3.385 1.458,3.385 1.313,3.385 false 2.063,2.417 2.333,2.656 0.271,0.24 10 false *a 1.125,3.313 1.281,3.5 0.156,0.188 10 false *b 1.667,3.688 1.813,3.906 0.146,0.219 10 true A 1.677,3.979 1.823,4.198 0.146,0.219 10 true B

Using a cylinder gauge, measure the cylinder bore diameter at positions A and B in both the thrust and axial directions.

Text in Illustration
*a Thrust Direction
*b Axial Direction
V100135

Engine Front

Standard diameter:

80.500 to 80.513 mm (3.169 to 3.170 in.)


Maximum diameter:

80.63 mm (3.174 in.)


Measurement Position:
Measurement Position Cylinder Bore Position
A 10 mm (0.394 in.) from top edge
B 50 mm (1.97 in.) from top edge


If the average diameter of the 4 positions is more than the maximum, replace the cylinder block.


Hide 13101 3.INSPECT PISTON

a.
A157790

Using a gasket scraper, remove the carbon from the piston top.


b.
A157791

Using a groove cleaning tool or broken ring, clean the piston ring grooves.


c.
A157792

Using a brush and solvent, thoroughly clean the piston.

NOTICE:

Do not use a wire brush.



d.
A199331E04
0.695,1.735 1.270,1.888 0.575,0.153 10 8.0 mm

Using a micrometer, measure the piston diameter at a position that is 8.0 mm (0.315 in.) from the bottom of the piston (refer to the illustration).

Standard piston diameter:

80.461 to 80.471 mm (3.1677 to 3.1681 in.)


If the diameter is not as specified, replace the piston with pin.


Hide 4.INSPECT PISTON OIL CLEARANCE

a.

Subtract the piston diameter measurement from the cylinder bore diameter measurement.

Standard oil clearance:

0.009 to 0.042 mm (0.000354 to 0.00165 in.)


Maximum oil clearance:

0.08 mm (0.00315 in.)


If the oil clearance is more than the maximum, replace all the pistons. If necessary, replace the cylinder block.


Hide 5.INSPECT RING GROOVE CLEARANCE

a.
A151006

Using a feeler gauge, measure the clearance between a new piston ring and the wall of the ring groove.

Standard Ring Groove Clearance:
Item Specified Condition
No. 1 Compression Ring 0.02 to 0.07 mm (0.000787 to 0.00276 in.)
No. 2 Compression Ring 0.02 to 0.055 mm (0.000787 to 0.00217 in.)
Oil Ring
(2-piece Type)
0.02 to 0.06 mm (0.000787 to 0.00236 in.)
Oil Ring
(3-piece Type)
0.07 to 0.13 mm (0.00276 to 0.00512 in.)


If the groove clearance is not as specified, replace the piston with pin.


Hide 6.INSPECT PISTON RING END GAP

a.
A151007E08
2.524,1.176 3.095,1.382 0.571,0.206 10 50 mm

Using a piston, push the piston ring a little beyond the bottom of the ring travel, 50 mm (1.97 in.) from the top of the cylinder block.


b.
A444566C01
2.375,1.365 2.26,1.365 2.26,1.365 2.083,1.094 false 2.427,1.281 2.74,1.479 0.313,0.198 10 false *a
*a Paint Mark
V100135

Upward


EM02552

Using a feeler gauge, measure the end gap.

Piston Ring Mark:
Item Type Paint Mark
No. 1 Compression Ring A Pink
B Orange


Standard End Gap:
Item Specified Condition
No. 1 Compression Ring (Type A) 0.20 to 0.30 mm (0.00787 to 0.0118 in.)
No. 1 Compression Ring (Type B) 0.24 to 0.28 mm (0.00945 to 0.01102 in.)
No. 2 Compression Ring 0.30 to 0.45 mm (0.0118 to 0.0177 in.)
Oil Ring 0.10 to 0.35 mm (0.00394 to 0.0138 in.)


Maximum End Gap:
Item Specified Condition
No. 1 Compression Ring 0.50 mm (0.0197 in.)
No. 2 Compression Ring 0.70 mm (0.0276 in.)
Oil Ring 0.70 mm (0.0276 in.)


If the end gap is more than the maximum, replace the piston ring. If the end gap is more than the maximum even with a new piston ring, replace the cylinder block.


Hide 7.INSPECT PISTON PIN OIL CLEARANCE

HINT:

There is only 1 type of supply part for piston with pin.


a.
A151008

Using a caliper gauge, measure the piston pin bore diameter.

Standard piston pin bore diameter:

20.006 to 20.015 mm (0.78764 to 0.78799 in.)

Item Specified Condition
Mark A 20.006 to 20.009 mm (0.78764 to 0.78775 in.)
Mark B 20.010 to 20.012 mm (0.78779 to 0.78787 in.)
Mark C 20.013 to 20.015 mm (0.78791 to 0.78799 in.)


If the diameter is not as specified, replace the piston with pin.


b.
A146331E18
1.292,2.406 1.438,2.604 0.146,0.198 10 false a 1.667,1.198 1.813,1.396 0.146,0.198 10 false b 1.677,2.969 1.823,3.167 0.146,0.198 10 false b

Using a micrometer, measure the piston pin diameter.

Standard piston pin diameter:

20.004 to 20.013 mm (0.78756 to 0.78791 in.)

Item Specified Condition
Mark A 20.004 to 20.007 mm (0.78756 to 0.78768 in.)
Mark B 20.008 to 20.010 mm (0.78771 to 0.78779 in.)
Mark C 20.011 to 20.013 mm (0.78783 to 0.78791 in.)


If the diameter is not as specified, replace the piston with pin.

Measurement Position:
Measurement Position Piston Pin Position
a 25 mm (0.984 in.) from side edge
b 5 mm (0.197 in.) from side edge



c.
A001185

Using a caliper gauge, measure the connecting rod small end bore diameter.

Standard connecting rod small end bore diameter:

20.012 to 20.021 mm (0.78787 to 0.78823 in.)

Item Specified Condition
Mark A 20.012 to 20.015 mm (0.78787 to 0.78799 in.)
Mark B 20.016 to 20.018 mm (0.78803 to 0.78811 in.)
Mark C 20.019 to 20.021 mm (0.78815 to 0.78823 in.)


If the diameter is not as specified, replace the connecting rod.


d.
A352268E01
0.25,0.417 0.385,0.417 0.385,0.417 0.542,1.635 false 0.677,2.219 0.677,1.385 false 2.25,2.333 2.25,2.156 2.25,2.156 2.677,1.042 false 1.896,3.927 2.292,3.292 2.292,3.292 2.438,3.292 false 1.177,3.177 1.313,3.177 1.313,3.177 1.469,4.396 false 0.833,0.219 1.146,0.417 0.313,0.198 10 false *a 2.417,0.24 2.729,0.438 0.313,0.198 10 false *b 0.052,0.313 0.365,0.51 0.313,0.198 10 false *c 0.604,2.24 0.917,2.438 0.313,0.198 10 false *d 2.219,2.385 2.531,2.583 0.313,0.198 10 false *c 2.51,3.219 2.823,3.417 0.313,0.198 10 false *c 0.99,3.083 1.302,3.281 0.313,0.198 10 false *e

Subtract the piston pin diameter measurement from the piston pin bore diameter measurement.

Text in Illustration
*a Upper Side:
*b Lower Side:
*c Front Mark
*d Piston Pin Bore Diameter Mark
*e Connecting Rod Small Bore Diameter Mark

Standard oil clearance:

-0.001 to 0.005 mm (-0.0000394 to 0.000197 in.)


Maximum oil clearance:

0.010 mm (0.000394 in.)


If the oil clearance is more than the maximum, replace the connecting rod. If necessary, replace the piston with pin as a set.


e.

Subtract the piston pin diameter measurement from the connecting rod small end bore diameter measurement.

Standard oil clearance:

0.005 to 0.011 mm (0.000197 to 0.000433 in.)


Maximum oil clearance:

0.014 mm (0.000551 in.)


If the oil clearance is more than the maximum, replace the connecting rod small end bush. If necessary, replace the piston with pin as a set.


Hide 13201 8.INSPECT CONNECTING ROD SUB-ASSEMBLY

a.
Z000064

Using a connecting rod aligner and feeler gauge, check the connecting rod alignment.

i.

Check for misalignment.

Maximum misalignment:

0.05 mm (0.00197 in.) per 100 mm (3.94 in.)


If the misalignment is more than the maximum, replace the connecting rod.


ii.
Z000065

Check for twist.

Maximum twist:

0.15 mm (0.00591 in.) per 100 mm (3.94 in.)


If the twist is more than the maximum, replace the connecting rod.



Hide 13411 9.INSPECT CRANKSHAFT

a.

Inspect the circle runout.

i.
A205912

Using a dial indicator and V-blocks, measure the circle runout as shown in the illustration.

Maximum circle runout:

0.03 mm (0.00118 in.)


If the circle runout is more than the maximum, replace the crankshaft.



b.

Inspect the main journals.

i.
A205913E02
1.308,1.755 1.667,1.902 0.359,0.147 10 No. 1 2.568,1.69 2.951,1.841 0.383,0.151 10 No. 2 2.568,1.971 2.948,2.118 0.379,0.147 10 No. 3 1.325,2.225 1.708,2.386 0.383,0.161 10 No. 4 2.568,2.242 2.926,2.378 0.358,0.137 10 No. 5 2.006,1.829 1.776,1.829 false 2.006,2.319 1.789,2.319 false 2.321,1.768 2.528,1.768 false 2.321,2.052 2.526,2.052 false 2.321,2.321 2.524,2.321 false

Using a micrometer, measure the diameter of each main journal.

Standard diameter:

47.988 to 48.000 mm (1.8893 to 1.8898 in.)


If the diameter is not as specified, check the crankshaft oil clearance.


ii.

Check each main journal for taper and distortion as shown in the illustration.

Maximum taper and distortion:

0.004 mm (0.000157 in.)


If the taper and distortion are more than the maximum, replace the crankshaft.

Standard Diameter (Reference):
Mark Specified Condition
0 47.999 to 48.000 mm (1.88972 to 1.88976 in.)
1 47.997 to 47.998 mm (1.88964 to 1.88968 in.)
2 47.995 to 47.996 mm (1.88956 to 1.88960 in.)
3 47.993 to 47.994 mm (1.88948 to 1.88952 in.)
4 47.991 to 47.992 mm (1.88941 to 1.88945 in.)
5 47.988 to 47.990 mm (1.88929 to 1.88937 in.)




c.

Inspect the crank pin.

i.
ZF06928

Using a micrometer, measure the diameter of each crank pin.

Standard diameter:

43.992 to 44.000 mm (1.7320 to 1.7323 in.)


If the diameter is not as specified, check the connecting rod oil clearance.


ii.

Inspect each crank pin for taper and distortion.

Maximum taper and distortion:

0.004 mm (0.000157 in.)


If the taper and distortion are more than the maximum, replace the crankshaft.



Hide 10.INSPECT CRANKSHAFT OIL CLEARANCE

a.

Check the crankshaft journals and bearings for pitting and scratches.



c.

Install the upper crankshaft thrust washers (See page Engine / Hybrid System>2ZR-FXE (ENGINE MECHANICAL)>CYLINDER BLOCK>REASSEMBLY).


d.

Clean each main journal and bearing.


e.

Place the crankshaft on the cylinder block.


f.
A151012E02
0.704,0.295 0.924,0.470 0.220,0.175 10 *1 0.914,0.375 1.035,0.375 1.035,0.375 1.402,1.297 false

Lay a strip of Plastigage across each journal.

Text in Illustration
*1 Plastigage


g.

Examine the front marks and numbers and place the bearing caps on the cylinder block.

HINT:

A number is marked on each crankshaft bearing cap to indicate the installation position.



h.

Install the crankshaft bearing cap (See page Engine / Hybrid System>2ZR-FXE (ENGINE MECHANICAL)>CYLINDER BLOCK>REASSEMBLY).

NOTICE:

Do not turn the crankshaft.



i.

j.

Measure the Plastigage at its widest point.

A205916E10
0.688,1.448 0.396,0.833 0.396,0.833 0.271,0.833 false 6.135,1.667 5.948,1.667 false 6.135,1.958 5.969,1.958 false 6.323,1.792 6.49,1.792 false 3.427,1.688 3.427,1.927 false 3.615,1.698 3.615,2.188 false 3.833,1.688 3.833,1.927 false 4.031,1.688 4.031,2.146 false 4.219,1.688 4.219,1.927 false 2.75,1.656 2.323,1.958 2.323,1.958 2.323,2.042 false 4.875,1.823 4.781,1.875 4.781,1.875 4.781,2.448 false 4.885,1.99 4.781,2.073 false 6.49,1.583 6.438,1.583 6.438,1.583 6.323,1.656 false 6.5,2.042 6.427,2.042 6.427,2.042 6.323,1.99 false 0.125,0.76 0.292,0.896 0.167,0.135 10 false *1 5.573,1.604 5.927,1.75 0.354,0.146 10 false No. 1 6.552,1.51 6.938,1.656 0.385,0.146 10 false No. 2 6.552,1.729 6.927,1.875 0.375,0.146 10 false No. 3 5.583,1.896 5.969,2.052 0.385,0.156 10 false No. 4 6.552,1.958 6.927,2.135 0.375,0.177 10 false No. 5 3.24,1.927 3.594,2.073 0.354,0.146 10 false No. 1 3.448,2.188 3.833,2.333 0.385,0.146 10 false No. 2 3.646,1.927 4.021,2.073 0.375,0.146 10 false No. 3 3.896,2.188 4.281,2.344 0.385,0.156 10 false No. 4 4.063,1.927 4.417,2.063 0.354,0.135 10 false No. 5 2.25,2.052 2.406,2.219 0.156,0.167 10 false *a 4.719,2.458 4.875,2.604 0.156,0.146 10 false *a

Text in Illustration
*1 Plastigage *a Number Mark

Standard oil clearance:

0.016 to 0.039 mm (0.000630 to 0.00154 in.)


Maximum oil clearance:

0.050 mm (0.00197 in.)


If the oil clearance is more than the maximum, replace the crankshaft bearing. If necessary, replace the crankshaft.

NOTICE:

Remove the Plastigage completely after the measurement.


HINT:

If replacing a bearing, select a new one with the same number. If the number of the bearing cannot be determined, calculate the correct bearing number by adding together the numbers imprinted on the cylinder block and crankshaft. Then select a new bearing with the calculated number according to the chart below. There are 4 sizes of standard bearings, marked "1", "2", "3" and "4" accordingly.


Example:

Cylinder block "3" + Crankshaft "5" = Total number 8 (Use bearing "3")

Bearing Chart
Cylinder Block + Crankshaft Bearing to be Used
0 to 2 "1"
3 to 5 "2"
6 to 8 "3"
9 to 11 "4"


Standard Cylinder Block Journal Bore Diameter:
Item Specified Condition
Mark 0 52.000 to 52.002 mm (2.04724 to 2.04732 in.)
Mark 1 52.003 to 52.004 mm (2.04736 to 2.04740 in.)
Mark 2 52.005 to 52.006 mm (2.04744 to 2.04752 in.)
Mark 3 52.007 to 52.009 mm (2.04752 to 2.04759 in.)
Mark 4 52.010 to 52.011 mm (2.04763 to 2.04767 in.)
Mark 5 52.012 to 52.013 mm (2.04771 to 2.04775 in.)
Mark 6 52.014 to 52.016 mm (2.04779 to 2.04787 in.)


Standard Crankshaft Journal Diameter:
Item Specified Condition
Mark 0 47.999 to 48.000 mm (1.88972 to 1.88976 in.)
Mark 1 47.997 to 47.998 mm (1.88964 to 1.88968 in.)
Mark 2 47.995 to 47.996 mm (1.88956 to 1.88961 in.)
Mark 3 47.993 to 47.994 mm (1.88948 to 1.88952 in.)
Mark 4 47.991 to 47.992 mm (1.88941 to 1.88945 in.)
Mark 5 47.988 to 47.990 mm (1.88929 to 1.88937 in.)


Standard Bearing Center Wall Thickness:
Item Specified Condition
Mark 1 1.994 to 1.997 mm (0.07850 to 0.07862 in.)
Mark 2 1.998 to 2.000 mm (0.07866 to 0.07874 in.)
Mark 3 2.001 to 2.003 mm (0.07878 to 0.07886 in.)
Mark 4 2.004 to 2.006 mm (0.07890 to 0.07898 in.)



Hide 11416 11.INSPECT CRANKSHAFT BEARING CAP SET BOLT

a.
A209192E03
1.567,1.728 1.739,1.893 0.172,0.165 10 *b 1.756,1.085 1.932,1.237 0.176,0.153 10 *a 1.332,2.938 1.499,3.093 0.167,0.155 10 *c

Using a vernier caliper, measure the length of the crankshaft bearing cap set bolt from the seat to end.

Text in Illustration
*a Measurement Length
*b Measurement Area
*c Distance

Standard bolt length:

84.3 to 85.7 mm (3.32 to 3.37 in.)


Maximum bolt length:

86.7 mm (3.41 in.)


HINT:
·

If the bolt length is greater than the maximum, replace the crankshaft bearing cap set bolt with a new one. Failure to do so may lead to engine damage.

·

If there is any thread deformation, replace the crankshaft bearing cap set bolt with a new one.




b.

Using a vernier caliper, measure the diameter of the threaded portion of the bolt at its thinnest point.

HINT:

Use a straightedge to determine the thinnest point of the threaded portion of the bolt.


Measurement point:

55.0 mm (2.17 in.)


Standard diameter:

9.77 to 9.96 mm (0.385 to 0.392 in.)


Minimum diameter:

9.1 mm (0.358 in.)


HINT:
·

If the diameter is less than the minimum, replace the crankshaft bearing cap set bolt with a new one. Failure to do so may lead to engine damage.

·

If there is any thread deformation, replace the crankshaft bearing cap set bolt with a new one.




Hide 13265 12.INSPECT CONNECTING ROD BOLT

a.
A109692E09
1.548,0.461 1.749,0.607 0.201,0.146 10 *a

Using a vernier caliper, measure the diameter of the bolt in the area shown in the illustration.

Text in Illustration
*a Measurement Area

Standard diameter:

6.6 to 6.7 mm (0.260 to 0.264 in.)


Minimum diameter:

6.4 mm (0.252 in.)


HINT:
·

Diameter measurements should be done at several points.

·

If the diameter is less than the minimum, replace the connecting rod bolt with a new one. Failure to do so may lead to engine damage.

·

If there is any thread deformation, replace the connecting rod bolt with a new one.




Hide 15708 13.INSPECT NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.
A198191

Push the check valve with a pin to check if it is stuck.

If stuck, replace the No. 1 oil nozzle.


b.

Push the check valve with a pin to check if it moves smoothly.

If it does not move smoothly, clean or replace the No. 1 oil nozzle.


c.
U110416E01
1.431,0.477 1.545,0.637 0.114,0.161 10 A 2.209,1.055 2.351,1.202 0.142,0.147 10 B

Apply air into A. Check that air does not leak through B.

If air leaks, clean or replace the No. 1 oil nozzle.


d.
U110417E01
1.442,0.485 1.556,0.646 0.114,0.161 10 A 1.906,1.471 2.048,1.617 0.142,0.147 10 B

Push the check valve while applying air into A. Check that air passes through B.

If air does not pass through B, clean or replace the No. 1 oil nozzle.