Home › Engine / Hybrid System › 2ZR-FXE (FUEL) › FUEL INJECTOR
RM2070E _51 Engine / Hybrid System _061908 2ZR-FXE FUEL _0301603 FUEL INJECTOR G

2ZR-FXE FUEL  FUEL INJECTOR  INSPECTION  


PROCEDURE

Hide 23250 1.INSPECT FUEL INJECTOR ASSEMBLY

a.

Check the resistance.

i.

Using an ohmmeter, measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 11.6 to 12.4 Ω


If the result is not as specified, replace the injector assembly.



b.

Check the operation.

Inspect the injector injection volume.

CAUTION:

Perform the inspection in a well-ventilated area.

Do not perform the inspection near an open flame.


i.
A264971E19
0.521,1.667 0.75,1.896 0.75,1.896 0.854,1.896 false 0.865,0.896 1.156,0.604 1.156,0.604 1.271,0.604 false 1.979,1.281 2.281,1.583 2.281,1.583 2.406,1.583 false 2.646,0.698 2.948,0.396 2.948,0.396 3.063,0.396 false 0.885,1.823 1.063,2 0.177,0.177 10 false *1 1.302,0.521 1.479,0.698 0.177,0.177 10 false *2 2.427,1.49 2.604,1.667 0.177,0.177 10 false *3 3.094,0.313 3.271,0.49 0.177,0.177 10 false *4

Connect SST (fuel tube connector) to SST (hose) with SST (hose band), and then connect them to the fuel pipe (vehicle side).

Text in Illustration
*1 SST
(Hose)
*2 SST
(Hose Band)
*3 SST
(Fuel Tube Connector)
*4 Fuel Pipe (Vehicle Side)

SST
09268-31014  (09268-41500, 09268-41700, 95336-08070)

NOTICE:

Ensure that the SST connector O-rings are not damaged and are free of foreign matter as they are used to seal the connections between the fuel tube connector and pipe.



ii.
A264972E17
1.333,0.125 0.958,0.125 false 1.74,0.281 2.031,0.281 false 1.313,0.75 0.979,0.75 false 1.479,1.021 1.646,1.021 false 2.104,1.354 2.448,1.354 false 1.333,1.854 0.99,1.854 false 0.781,0.052 0.948,0.229 0.167,0.177 10 false *1 2.073,0.208 2.24,0.385 0.167,0.177 10 false *2 0.813,0.677 0.979,0.854 0.167,0.177 10 false *3 1.677,0.958 1.844,1.135 0.167,0.177 10 false *4 2.49,1.271 2.656,1.448 0.167,0.177 10 false *5 0.813,1.771 0.979,1.948 0.167,0.177 10 false *6

Install a new O-ring onto the fuel injector assembly.

Text in Illustration
*1 SST
(Hose)
*2 SST
(Hose Band)
*3 SST
(Adapter)
*4 O-ring
*5 SST
(Clamp)
*6 Vinyl Tube

SST
09268-31014  (09268-41110, 09268-41300, 09268-41700, 95336-08070)


iii.

Connect SST (adapter and hose) to the injector assembly, and hold the injector assembly and union with SST (clamp).


iv.

Install a vinyl tube onto the injector.

CAUTION:

Install a suitable vinyl tube onto the injector assembly to prevent gasoline from spraying.



v.
A264974E15
1.938,0.385 2.469,0.385 false 2.125,1.406 2.49,1.406 false 1.26,0.375 0.771,0.375 false 0.573,0.292 0.76,0.469 0.188,0.177 10 false *1 2.521,0.292 2.708,0.469 0.188,0.177 10 false *2 2.531,1.313 2.719,1.49 0.188,0.177 10 false *3

Tie SST (clamp and adapter) together with SST (tie band) as shown in the illustration.

Text in Illustration
*1 SST
(Tie Band)
*2 SST
(Adapter)
*3 SST
(Clamp)

SST
09268-31014  (09268-41110, 09268-41300, 09268-41800)


vi.

Set the injector assembly in a graduated cylinder.



viii.
A264973E21
2.031,0.542 2.031,0.958 false 1.969,1 2.125,1.24 0.156,0.24 10 false *1 1.063,1.302 1.219,1.542 0.156,0.24 10 false *a

Connect SST (wire) to the injector assembly and the auxiliary battery for 15 seconds, and measure the injection volume with the graduated cylinder. Test each injector 2 or 3 times.

Text in Illustration
*1 SST
(Wire)
*a Connect

SST
09842-30080  

NOTICE:

Always do the switching on the auxiliary battery side.


Standard Injection Volume:
Tester Connection Condition Specified Condition
Positive terminal - Ground terminal Per 15 seconds 60 to 73 cc (3.7 to 4.5 cu.in.)


Difference between each injector:

13 cc (0.8 cu.in.) or less


If the injection volume is not as specified, replace the injector assembly.



c.

Inspect for leaks.

i.

In the condition above, disconnect the test probes of SST (wire) from the auxiliary battery and check for fuel leaks from the injector.

Standard fuel drop:

1 drop or less every 12 minutes


If there are excessive leaks, replace the injector assembly.