77213E
1.INSTALL FUEL TANK TO FILLER PIPE HOSE
Install the fuel tank to filler pipe hose to the fuel tank as shown in the illustration, then fit the hose with the clamp.
| *a | Up |
| *b | 90° |
| *c | 60°
(Clip Area) |
77754B
2.INSTALL CHARCOAL CANISTER OUTLET HOSE
Connect the No. 1 fuel tube clamp to the fuel tank breather tube.
Install the charcoal canister outlet hose to the No. 1 fuel tube clamp.
77026A
3.INSTALL NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY
Install the No. 1 fuel evaporation tube sub-assembly to the fuel tank assembly.
77209F
4.INSTALL FUEL TANK MAIN TUBE SUB-ASSEMBLY
Install the fuel tank main tube sub-assembly to the fuel tank assembly.
77651A
5.INSTALL NO. 1 FUEL TANK CUSHION
Install 4 new No. 1 fuel tank cushions as shown in the illustration.
| *1 | No. 1 Fuel Tank Cushion |
| *2 | No. 2 Fuel Tank Cushion |
77652A
6.INSTALL NO. 2 FUEL TANK CUSHION
Install 2 new No. 2 fuel tank cushions as shown in the illustration.
77100
7.INSTALL FUEL TANK ASSEMBLY
Support the fuel tank using an engine lifter.
Raise the engine lifter, then install the fuel tank to the vehicle.
Do not drop the fuel tank.
When installing the fuel tank, tilt it slightly to prevent it from interfering with the suspension arm or other surrounding parts.
Tighten the 4 set bolts of the 2 fuel tank bands.
77209F
8.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY
Align the quick connector with the pipe, connect the quick connector and push the retainer in until the retainer makes a "click" sound to lock the claws of the retainer.
| *1 | Retainer |
| *2 | Fuel Tube Connector |
| *3 | Fuel Tank Main Tube |
| *4 | Fuel Pipe |
| *5 | O-ring |
|
Push |
Check that there are no scratches or foreign matter around the connected part of the fuel tube connector and fuel pipe before starting this step.
After connecting the fuel tube connector, check that the fuel tube connector is securely connected by pulling on the fuel tube connector.
77026A
9.CONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY
Connect the No. 1 fuel evaporation tube sub-assembly, then fit it with the clip as shown in the illustration.
| *a | Up |
| *b | 90° |
Check that there is no damage or foreign matter around the connecting parts of the No. 1 fuel evaporation tube sub-assembly and fuel pipe before performing this work.
77213E
10.CONNECT FUEL TANK TO FILLER PIPE HOSE
Connect the fuel tank to filler pipe hose to the fuel tank, then fit it with the clamp as shown in the illustration.
| *a | Up |
| *b | 2.5 to 5.5 mm (0.0984 to 0.217 in.) |
| *c | 90° |
11.REMOVE FUEL TANK BREATHER TUBE
Connect the fuel tank breather tube to the fuel tank as shown in the illustration, then fit it with the clamp.
| *1 | Fuel Tank Breather Tube |
| *2 | Charcoal Canister Outlet Hose |
| *3 | Breather Tube Clamp |
| *a | Up |
| *b | 60° |
| *c | 30° |
77754B
12.CONNECT CHARCOAL CANISTER OUTLET HOSE
Connect the charcoal canister outlet hose.
Connect the charcoal canister outlet hose and fuel tank breather tube to the breather tube clamp.
77641A
13.INSTALL NO. 1 FUEL TANK PROTECTOR
Install the No. 1 fuel tank protector with the 4 clips.
53605F
14.INSTALL REAR SUSPENSION BRACE SUB-ASSEMBLY
57627A
15.INSTALL REAR FLOOR SIDE MEMBER COVER RH
17410
16.INSTALL FRONT EXHAUST PIPE ASSEMBLY
77020A
17.INSTALL FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
18.ADD FUEL
19.INSPECT FOR EXHAUST GAS LEAK