Home › Suspension › REAR SUSPENSION › REAR AXLE BEAM › 2012.03–2013.08
RM2070E _53 Suspension _061920 REAR SUSPENSION _0301675 REAR AXLE BEAM A

REAR SUSPENSION  REAR AXLE BEAM  INSTALLATION  


PROCEDURE

Hide 48725G 1.INSTALL REAR AXLE CARRIER BUSHING LH

a.
C159021E16
2.094,1.375 1.844,1.635 1.844,1.635 1.292,1.635 true 1.083,1.552 1.292,1.76 0.208,0.208 10 true *a

Align the arrow mark on a new rear axle carrier bushing LH with the matchmark on the rear axle beam assembly and temporarily install the rear axle carrier bushing LH to the rear axle beam assembly. (If the rear axle beam assembly is reused.)

Text in Illustration
*a Matchmark

NOTICE:

Be sure to install the rear axle carrier bushing in the same direction as it was before removal.

The rear axle carrier bushing has to be installed in a specific direction.



b.
C236528E01
1.061,1.835 0.729,1.835 false 0.547,1.735 0.711,1.880 0.164,0.144 10 *a 1.832,0.782 1.995,0.926 0.164,0.144 10 *b

Temporarily install the new rear axle carrier bushing LH as shown in the illustration.

Text in Illustration
*a Mark
*b 75°
V100135

Upper Side of the Vehicle
V100136

Front of the Vehicle

NOTICE:

Be sure to install the rear axle carrier bushing in the same direction as it was before removal.

The rear axle carrier bushing has to be installed in a specific direction.



c.

Using SST, install the rear axle carrier bushing LH to the rear axle beam assembly.

C370357E01
2.771,2.583 1.031,2.583 1.031,2.583 1.031,1.906 true 1.49,2.583 1.49,1.594 true 1.698,2.583 1.698,1.438 true 1.625,2.583 1.625,1.448 true 1.833,0 2.146,0.198 0.313,0.198 10 true *b 2.844,2.49 3.26,2.698 0.417,0.208 10 false SST 3.135,1.281 3.448,1.479 0.313,0.198 10 false *a

Text in Illustration
*a Turn
*b Hold

SST
09710-30012  (09710-04101)
09950-40011  (09951-04020, 09952-04010, 09953-04030, 09954-04020, 09955-04051, 09957-04010, 09958-04011)
09950-60010  (09951-00620)

NOTICE:
·

Do not damage the rubber portion when installing the rear axle carrier bushing.

·

Apply grease to the threads and tip of the SST center bolt before use.




Hide 48725F 2.INSTALL REAR AXLE CARRIER BUSHING RH

HINT:

Perform the same procedure as for the LH side.


Hide 42110F 3.TEMPORARILY TIGHTEN REAR AXLE BEAM ASSEMBLY

a.

Slowly jack up the rear axle beam assembly with an engine lifter using 2 wooden blocks and 2 attachments or equivalent tools and temporarily install the rear axle beam assembly to the body with the 2 bolts (B).

C207252E05
4.938,2.083 4.938,2.271 false 1.99,1.75 1.99,2 1.99,2 2.135,2 false 2.74,1.76 2.74,1.906 false 4.521,1.74 4.521,1.906 false 5.24,1.75 5.24,1.979 5.24,1.979 5.073,1.979 false 4.875,2.281 5.052,2.438 0.177,0.156 10 false *1 2.146,1.917 2.323,2.073 0.177,0.156 10 false *2 2.677,1.906 2.854,2.073 0.177,0.167 10 false *3 4.448,1.917 4.625,2.083 0.177,0.167 10 false *3 4.906,1.906 5.083,2.063 0.177,0.156 10 false *2 1.76,1.521 2,1.677 0.24,0.156 10 true (A) 0.344,1.771 0.583,1.927 0.24,0.156 10 false (B) 5.26,1.49 5.469,1.677 0.208,0.188 10 true (A) 6.667,1.76 6.917,1.917 0.25,0.156 10 false (B)

Text in Illustration
*1 Engine Lifter *2 Wooden Block
*3 Attachment - -

NOTICE:

Make sure to secure the rear axle beam assembly to prevent it from dropping.



b.

Temporarily tighten the rear axle beam assembly to the rear shock absorber assemblies LH and RH with the 2 bolts (A) and 2 nuts.

NOTICE:

Since the stopper nuts are used, turn the bolts.


HINT:

Insert the bolts with the threaded end facing the outside of the vehicle.



Hide 48259A 4.INSTALL REAR UPPER COIL SPRING INSULATOR LH

Hide 48257C 5.INSTALL REAR UPPER COIL SPRING INSULATOR RH

HINT:

Perform the same procedure as for the LH side.


Hide 48258C 6.INSTALL REAR LOWER COIL SPRING INSULATOR LH

Hide 48258B 7.INSTALL REAR LOWER COIL SPRING INSULATOR RH

Hide 48231B 8.INSTALL REAR COIL SPRING LH

Hide 48231A 9.INSTALL REAR COIL SPRING RH

HINT:

Perform the same procedure as for the LH side.


Hide 89407A 10.INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY (w/ Height Control Sensor)

Hide 11.TEMPORARILY TIGHTEN PARKING BRAKE ASSEMBLY (for LH Side)

a.

Clean the installation surfaces of the parking brake assembly and rear axle beam assembly.


b.

Temporarily tighten the parking brake assembly to the rear axle beam assembly with the nut.

NOTICE:

Do not twist the No. 3 parking brake cable assembly when installing the parking brake assembly.


HINT:

Fully tighten the nut after installing the rear axle hub and bearing assembly.



c.

Install the No. 3 parking brake cable assembly to the rear axle beam assembly with the bolt.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 12.TEMPORARILY TIGHTEN PARKING BRAKE ASSEMBLY (for RH Side)

HINT:

Perform the same procedure as for the LH side.


Hide 42450B 13.INSTALL REAR AXLE HUB AND BEARING ASSEMBLY LH

Hide 42450A 14.INSTALL REAR AXLE HUB AND BEARING ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 15.FULLY TIGHTEN PARKING BRAKE ASSEMBLY (for LH Side)

a.

Fully tighten the nut.

Torque:
140 N*m (1428 kgf*cm, 103 ft.*lbf)


Hide 16.FULLY TIGHTEN PARKING BRAKE ASSEMBLY (for RH Side)

HINT:

Perform the same procedure as for the LH side.


Hide 47324 17.INSTALL REAR NO. 4 BRAKE TUBE

a.
C155135

Install the rear No. 4 brake tube to the rear axle beam assembly with the nut.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 47323 18.INSTALL REAR NO. 3 BRAKE TUBE

HINT:

Perform the same procedure as for the rear No. 4 brake tube.


Hide 47316A 19.CONNECT REAR BRAKE TUBE FLEXIBLE HOSE (for LH Side)

a.

Install the rear brake tube flexible hose with the bolt.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


b.

Using a union nut wrench, connect the rear brake tube flexible hose to the rear No. 4 brake tube.

Torque:
15 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not bend or damage the brake line.

·

Do not allow any foreign matter such as dirt and dust to enter the brake line from the connecting points.

·

Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).




Hide 47316A 20.CONNECT REAR BRAKE TUBE FLEXIBLE HOSE (for RH Side)

a.

Install the rear brake tube flexible hose with a new clip.

NOTICE:

Install the clip as far as it will go.



b.

Using a union nut wrench, connect the rear brake tube flexible hose to the rear No. 3 brake tube.

Torque:
15 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not bend or damage the brake line.

·

Do not allow any foreign matter such as dirt and dust to enter the brake line from the connecting points.

·

Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).




Hide 42431 21.INSTALL REAR DISC (for LH Side)

Hide 42431 22.INSTALL REAR DISC (for RH Side)

HINT:

Perform the same procedure as for the LH side.


Hide 42491 23.INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG

a.

Install the 2 parking brake shoe adjusting hole plugs.


Hide 24.INSTALL REAR DISC BRAKE CALIPER ASSEMBLY LH

a.

Install the rear disc brake caliper assembly LH with rear flexible hose LH with the 2 bolts.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)


b.

Connect the rear flexible hose LH to the rear axle beam assembly with a new clip.

NOTICE:

Install the clip as far as it will go.



c.

Using a union nut wrench, connect the rear No. 4 brake tube to the rear flexible hose LH while holding the rear flexible hose LH with a wrench.

Torque:
15 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not bend or damage the brake line.

·

Do not allow any foreign matter such as dirt and dust to enter the brake line from the connecting points.

·

Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).




Hide 25.INSTALL REAR DISC BRAKE CALIPER ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 89516D 26.INSTALL SKID CONTROL SENSOR WIRE LH

Hide 89516C 27.INSTALL SKID CONTROL SENSOR WIRE RH

HINT:

Perform the same procedure as for the LH side.


Hide 89516C 29.CONNECT SKID CONTROL SENSOR WIRE RH

HINT:

Perform the same procedure as for the LH side.


Hide 53605F 30.INSTALL REAR SUSPENSION BRACE SUB-ASSEMBLY

a.

for Type A:

i.

Install the rear suspension brace sub-assembly with the 4 bolts and clip.

Torque:
54 N*m (551 kgf*cm, 40 ft.*lbf)



b.

for Type B:

i.

Install the rear suspension brace sub-assembly with the 4 bolts.

Torque:
54 N*m (551 kgf*cm, 40 ft.*lbf)



Hide 31.FILL RESERVOIR WITH BRAKE FLUID

Hide 32.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

a.

Connect the cable to the negative (-) auxiliary battery terminal (See page Power Source / Network>2ZR-FXE (BATTERY / CHARGING)>AUXILIARY BATTERY>INSTALLATION).


Hide 57627A 34.INSTALL REAR FLOOR SIDE MEMBER COVER RH

a.

Engage the 3 clips to temporarily install the rear floor side member cover RH.


b.

Install the rear floor side member cover RH with the 3 bolts.


Hide 35.ADJUST PARKING BRAKE

Hide 36.INSTALL REAR WHEELS

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 42110F 38.FULLY TIGHTEN REAR AXLE BEAM ASSEMBLY

Hide 65638 39.INSTALL REAR WHEEL HOUSE LINER LH

Hide 65637 40.INSTALL REAR WHEEL HOUSE LINER RH

HINT:

Perform the same procedure as for the LH side.


Hide 42.PLACE FRONT WHEELS FACING STRAIGHT AHEAD

Hide 43.PERFORM YAW RATE AND ACCELERATION SENSOR CALIBRATION

Hide 45. INITIALIZE HEIGHT CONTROL SENSOR SIGNAL (w/ Height Control Sensor)

Hide 46.ADJUST HEADLIGHT AIMING (w/ Height Control Sensor)