Home › Engine / Hybrid System › 2ZR-FXE (FUEL) › FUEL PUMP › 2013.08–2014.11
RM2070E _51 Engine / Hybrid System _061908 2ZR-FXE FUEL _0301607 FUEL PUMP A

2ZR-FXE FUEL  FUEL PUMP  INSTALLATION  


PROCEDURE

Hide 77020A 1.INSTALL FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

a.
A251210E01
2.836,0.188 3.009,0.382 0.173,0.194 10 *1 2.606,0.442 2.752,0.295 2.752,0.295 2.833,0.295 false

Install a new fuel suction tube set gasket onto the fuel tank.

Text in Illustration
*1 Fuel Suction Tube Set Gasket


b.
A251211E02
1.094,4.031 1.094,4.344 false 2.396,4.031 2.396,4.229 2.396,4.229 1.094,4.229 false 1.177,2.052 2.354,2.906 2.354,2.906 2.354,1.552 false 2.281,2.938 2.448,3.115 0.167,0.177 10 false *a 1.01,4.333 1.177,4.51 0.167,0.177 10 false *b

Set the fuel suction tube with pump and gauge assembly to the fuel tank.

Text in Illustration
*a Notch
*b Protrusion

NOTICE:

Make sure that the fuel sender gauge arm does not bend.



c.

Align the protrusions of the fuel suction tube with pump and gauge assembly with the notches of the fuel tank.


Hide 77144 2.INSTALL FUEL PUMP GAUGE RETAINER

a.
A251212E01
2.555,1.401 2.742,1.561 0.187,0.160 10 *a 2.13,1.886 2.318,2.046 0.187,0.160 10 *b 1.469,1.904 1.657,2.065 0.187,0.160 10 *c 2.133,1.507 2.542,1.507 false 2.204,1.64 2.204,1.886 false

While holding the fuel suction tube with pump and gauge assembly by hand to prevent it from tilting, align the mark on the new fuel pump gauge retainer with the start mark on the fuel tank and tighten the fuel pump gauge retainer 180° by hand.

Text in Illustration
*a Start Mark
*b Mark
*c Front

HINT:
·

Check that there is no damage, dents, foreign matter, or other defects on the threads of the fuel tank.




b.
A251209E02
1.844,2.813 2.094,2.813 false 2.198,2.417 2.313,2.521 2.313,2.521 2.625,2.521 false 1.781,3.01 1.573,3.219 1.573,3.219 1.104,3.219 false 1.604,2.938 1.323,3.219 false 2.646,2.438 2.854,2.656 0.208,0.219 10 false *1 2.115,2.729 2.292,2.917 0.177,0.188 10 false *2 0.917,3.125 1.094,3.313 0.177,0.188 10 false *3

Temporarily install the SST plate and claws to the fuel pump gauge retainer.

Text in Illustration
*1 SST
(Plate)
*2 SST
(Claw)
*3 Rib

SST
09808-14030  (09808-01030, 09808-01040, 09808-01050)

HINT:

Engage the SST claws securely with the fuel pump gauge retainer ribs to secure SST.



c.

While pressing the claws of SST to the fuel pump gauge retainer ribs securely, tighten the bolts.

HINT:

Install SST while pressing the SST claws toward the fuel pump gauge retainer (toward the center of SST).



d.

Install the SST handle.


e.
A251213E02
1.448,2.844 1.052,3.021 1.052,3.021 0.917,3.021 false 1.26,0.635 1.552,0.344 1.552,0.344 1.635,0.344 false 1.229,1.146 0.667,1.698 0.667,1.698 0.563,1.698 true 2.073,0.625 2.292,0.406 2.292,0.406 2.469,0.406 false 1.969,4.323 2.156,4.49 0.188,0.167 10 false *b 1.667,0.26 1.833,0.51 0.167,0.25 10 false *1 0.375,1.615 0.542,1.865 0.167,0.25 10 false *3 2.51,0.333 2.677,0.583 0.167,0.25 10 false *2 0.719,2.927 0.906,3.146 0.188,0.219 10 false *a

Tighten the fuel pump gauge retainer approximately 360° so that the mark on the retainer comes within the range shown in the illustration.

Text in Illustration
*1 SST
(Handle)
*2 SST
(Plate)
*3 SST
(Claw)
*a Mark
*b Front

SST
09808-14030  (09808-01010, 09808-01020, 09808-01030, 09808-01040, 09808-01050)

NOTICE:
·

Do not use any tools other than specified in this operation. Damage to the fuel pump gauge retainer or the fuel tank may result.

·

Do not press down on SST excessively as this may make the retainer hard to rotate, and may damage components.

·

Make sure to rotate the SST handle horizontally. If the SST handle is rotated at an angle, SST may come off.

·

Do not spin SST too fast or use an impact wrench as this may result in damage to components.

·

If SST comes off of the retainer, loosen the SST bolts and reinstall SST.



HINT:
·

Lightly press down on SST to prevent it from separating from the retainer. While pressing SST, rotate the handle slowly to tighten the retainer.

·

The ribs on the fuel pump gauge retainer can be fitted into the tips of SST.




Hide 77026A 3.CONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY

a.
A248047

Connect the No. 1 fuel evaporation tube sub-assembly to the fuel suction tube with pump and gauge assembly with the clip.


Hide 77754B 4.CONNECT CHARCOAL CANISTER OUTLET HOSE

a.
A248046

Connect the charcoal canister outlet hose to the fuel suction tube with pump and gauge assembly.


Hide 77209F 5.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.

Push the fuel tube joint in the plug of the fuel suction plate, then install the tube joint clip.

A398188E01
0.844,2.219 0.844,1.406 false 4.875,0.26 5.333,0.26 false 5.844,0.51 6.135,0.51 false 5.594,0.781 6.219,0.781 false 5.615,0.656 6.219,0.656 6.219,0.656 6.219,1 false 4.906,1.958 5.177,1.958 false 4.708,2.063 4.969,2.375 4.969,2.375 5.188,2.375 false 5.813,2.01 6.115,1.802 6.115,1.802 6.323,1.802 false 6.021,2.031 6.354,2.031 false 0.781,2.24 1.094,2.438 0.313,0.198 10 false *1 4.688,0.177 5,0.375 0.313,0.198 10 false *2 6.125,1.063 6.438,1.26 0.313,0.198 10 false *3 6.365,1.729 6.677,1.927 0.313,0.198 10 false *4 4.458,1.385 5.375,1.615 0.917,0.229 10 false CORRECT 6.188,0.438 6.5,0.635 0.313,0.198 10 false *1 5.208,1.875 5.521,2.073 0.313,0.198 10 false *1 6.396,1.958 6.708,2.156 0.313,0.198 10 false *1 5.219,2.302 5.531,2.5 0.313,0.198 10 false *4 5.563,1.396 6.479,1.625 0.917,0.229 10 false INCORRECT

Text in Illustration
*1 Tube Joint Clip
*2 Fuel Tube Joint
*3 O-ring
*4 Collars

NOTICE:
·

Check that there are no scratches or foreign objects around the connected part of the fuel tube joint and plug before performing this work.

·

Check that the fuel tube joint is securely inserted to the end.

·

Check that the tube joint clip is on the collar of the fuel tube joint.

·

After installing the tube joint clip, check that the fuel tank main tube cannot be pushed out.




b.
A248044

Connect the fuel pump connector.


Hide 6.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 58325E 8.INSTALL REAR FLOOR SERVICE HOLE COVER

a.

Install the rear floor service hole cover with new butyl tape.


b.

Install the rear floor carpet with the 2 clips.


Hide 14.INSTALL REAR NO. 2 SEAT ASSEMBLY

Hide 15.INSTALL REAR NO. 1 SEAT ASSEMBLY (for Center)

Hide 16.INSTALL REAR NO. 1 SEAT ASSEMBLY (for Side)