Home › Engine / Hybrid System › 2ZR-FXE (FUEL) › FUEL PUMP › 2013.08–2014.11
RM2070E _51 Engine / Hybrid System _061908 2ZR-FXE FUEL _0301607 FUEL PUMP A

2ZR-FXE FUEL  FUEL PUMP  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.REMOVE REAR NO. 1 SEAT ASSEMBLY (for Side)

Hide 3.REMOVE REAR NO. 1 SEAT ASSEMBLY (for Center)

Hide 4.REMOVE REAR NO. 2 SEAT ASSEMBLY

Hide 58325E 5.REMOVE REAR FLOOR SERVICE HOLE COVER

a.
A248043

Using a clip remover, remove the 2 clips.


b.

Turn over the front floor carpet.


c.
A251243

Remove the rear floor service hole cover.


d.
A248044

Disconnect the connector from the fuel suction tube assembly.


Hide 6. DISCHARGE FUEL SYSTEM PRESSURE

Hide 12.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 77209F 13.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A248045E02
2.177,3.583 2.49,3.583 false 1.51,3.25 1.083,3.25 false 1.896,3.792 2.438,3.792 2.438,3.792 2.438,4.135 false 1.896,3.927 2.438,3.927 false 0.583,2.094 0.583,2.635 false 0.51,2.646 0.667,2.885 0.156,0.24 10 false *1 2.521,3.5 2.677,3.74 0.156,0.24 10 false *1 0.896,3.156 1.094,3.385 0.198,0.229 10 false *2 2.354,4.156 2.573,4.406 0.219,0.25 10 false *3

Remove the tube joint clip, then pull the fuel tube joint out of the plug of the fuel suction tube with pump and gauge assembly.

Text in Illustration
*1 Tube Joint Clip
*2 Fuel Tube Joint
*3 O-ring

NOTICE:
·

Check that there is no dirt or other foreign objects around the fuel tube joint before disconnecting it. Clean the joint if necessary.

·

It is necessary to prevent mud or dirt from entering the joint. If mud or dirt gets in the joint, the O-rings may not seal properly.

·

Only disconnect the joint by hand.

·

Do not bend, kink or twist the nylon tubes.

·

Protect the contact surfaces by covering it with a plastic bag.




Hide 77754B 14.DISCONNECT CHARCOAL CANISTER OUTLET HOSE

a.
A248046

Disconnect the charcoal canister outlet hose from the fuel suction tube with pump and gauge assembly.


Hide 77026A 15.DISCONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY

a.
A248047

Loosen the clip and disconnect the No. 1 fuel evaporation tube sub-assembly from the fuel suction tube with pump and gauge assembly.


Hide 77144 16.REMOVE FUEL PUMP GAUGE RETAINER

a.
A251209E02
1.844,2.813 2.094,2.813 false 2.198,2.417 2.313,2.521 2.313,2.521 2.625,2.521 false 1.781,3.01 1.573,3.219 1.573,3.219 1.104,3.219 false 1.604,2.938 1.323,3.219 false 2.646,2.438 2.854,2.656 0.208,0.219 10 false *1 2.115,2.729 2.292,2.917 0.177,0.188 10 false *2 0.917,3.125 1.094,3.313 0.177,0.188 10 false *3

Temporarily install the SST plate and claws to the fuel pump gauge retainer.

Text in Illustration
*1 SST
(Plate)
*2 SST
(Claw)
*3 Rib

SST
09808-14030  (09808-01030, 09808-01040, 09808-01050)

HINT:

Engage the SST claws securely with the fuel pump gauge retainer ribs to secure SST.



b.

While pressing the claws of SST to the fuel pump gauge retainer ribs securely, tighten the bolts.

HINT:

Install SST while pressing the SST claws toward the fuel pump gauge retainer (towards the center of SST).



c.

Install the SST handle.


d.
A245427E04
0.969,0.615 1.375,0.208 1.375,0.208 1.51,0.208 false 2.594,2.042 2.688,1.948 2.688,1.948 2.823,1.948 false 2.396,2.813 2.563,2.979 2.563,2.979 2.667,2.979 false 1.573,0.094 1.74,0.292 0.167,0.198 10 false *1 2.875,1.833 3.042,2.031 0.167,0.198 10 false *2 2.698,2.896 2.865,3.094 0.167,0.198 10 false *3

Lightly press down on SST to prevent it from separating from the retainer. While pressing SST, rotate the handle slowly to loosen the retainer.

Text in Illustration
*1 SST
(Handle)
*2 SST
(Plate)
*3 SST
(Claw)

SST
09808-14030  (09808-01010, 09808-01020, 09808-01030, 09808-01040, 09808-01050)

NOTICE:
·

Do not use any tools other than specified in this operation as this may result in damage to the fuel pump gauge retainer or the fuel tank.

·

Do not press down on SST excessively as this may make the retainer hard to rotate, and may damage components.

·

Make sure to rotate the SST handle horizontally. If the SST handle is rotated at an angle, SST may come off.

·

Do not spin SST too fast or use an impact wrench as this may result in damage to components.

·

If SST comes off of the retainer, loosen the SST bolts and reinstall SST.



HINT:

The ribs on the fuel pump gauge retainer can be fitted into the tips of SST.



e.

Remove the fuel pump gauge retainer while holding the fuel suction tube with pump and gauge assembly by hand.


Hide 77020A 17.REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

a.
A251244

Remove the fuel suction tube with pump and gauge assembly from the fuel tank.

NOTICE:

Make sure that the fuel sender gauge arm does not bend.



b.
A251210E01
2.836,0.188 3.009,0.382 0.173,0.194 10 *1 2.606,0.442 2.752,0.295 2.752,0.295 2.833,0.295 false

Remove the fuel suction tube set gasket from the fuel tank.

Text in Illustration
*1 Fuel Suction Tube Set Gasket