Home › Engine / Hybrid System › 2ZR-FXE (COOLING) › EXHAUST PIPE GAS CONTROL ACTUATOR › 2012.03–2020.08
RM2070E _51 Engine / Hybrid System _061911 2ZR-FXE COOLING _0301627 EXHAUST PIPE GAS CONTROL ACTUATOR A

2ZR-FXE COOLING  EXHAUST PIPE GAS CONTROL ACTUATOR  INSTALLATION  


PROCEDURE

Hide 17046 1.INSTALL EXHAUST PIPE GAS CONTROL ACTUATOR SUB-ASSEMBLY

a.
A290215

Clean the installation surfaces and bolt holes of the exhaust pipe gas control actuator sub-assembly and front exhaust pipe assembly.

NOTICE:

Make sure no foreign matter enters the cooling system when the exhaust pipe gas control actuator sub-assembly is removed.



b.
A399934E01
2.156,0.979 2.156,0.719 2.156,0.719 1.938,0.719 false 1.563,0.854 1.875,1.052 0.313,0.198 10 false A 1.75,0.635 2.063,0.833 0.313,0.198 10 false *1 2.385,0.51 2.698,0.708 0.313,0.198 10 false A-A 3.094,1.406 3.406,1.604 0.313,0.198 10 false *a 0.521,1.729 0.833,1.927 0.313,0.198 10 false A

If the engine coolant spilled when removing the front exhaust pipe assembly, add engine coolant up to the bottom edge of the flange as shown in the illustration.

Text in Illustration
*1 Flange
*a Fill up
V100145

Engine Coolant

HINT:

If a large amount of air enters the cooling system, the load on the engine water pump assembly will increase.



c.
A290220E04
1.031,0.479 0.854,0.479 0.854,0.479 0.75,0.635 false 1.073,1.427 0.979,1.427 0.979,1.427 0.885,1.25 false 1.729,4.458 1.854,4.458 1.854,4.458 1.865,4.344 false 2.271,4.083 2.156,4.083 false 1.563,4.375 1.729,4.542 0.167,0.167 10 false *1 2.292,4 2.458,4.167 0.167,0.167 10 false *2 1.063,0.385 1.229,0.552 0.167,0.167 10 false *1 1.094,1.333 1.26,1.5 0.167,0.167 10 false *2

Set the No. 2 exhaust pipe heat insulator on the front exhaust pipe assembly.

Text in Illustration
*1 Front Exhaust Pipe Assembly
*2 No. 2 Exhaust Pipe Heat Insulator

NOTICE:

Confirm that No. 2 exhaust pipe heat insulator is installed in the correct position.



d.
A292951E01
0.304,0.029 0.478,0.188 0.173,0.159 10 *a

Lift the rear side of the No. 2 exhaust pipe heat insulator to allow the exhaust pipe gas control actuator sub-assembly to be installed below the flange on the No. 2 exhaust pipe heat insulator.

Text in Illustration
*a Vehicle Front


e.
A290222E05
2.135,3.021 2.24,3.021 2.24,3.021 2.344,2.823 false 2.688,2.552 2.906,2.552 false 2.323,2.115 2.229,2.115 2.229,2.115 2.229,2.396 false 1.208,3.021 1.104,3.021 1.104,3.021 0.906,2.729 false 0.688,2.219 0.771,2.219 0.771,2.219 0.875,2.604 false 1.979,2.927 2.146,3.094 0.167,0.167 10 false *1 2.906,2.448 3.073,2.615 0.167,0.167 10 false *2 2.333,2.031 2.5,2.198 0.167,0.167 10 false *3 0.521,2.146 0.688,2.313 0.167,0.167 10 false *5 1.229,2.927 1.396,3.094 0.167,0.167 10 true *4

Set the exhaust pipe gas control actuator sub-assembly on the front exhaust pipe assembly as a set from the vehicle front.

Text in Illustration
*1 Front Exhaust Pipe Assembly
*2 No. 2 Exhaust Pipe Heat Insulator
*3 Exhaust Pipe Gas Control Actuator Sub-assembly
*4 Pin Top Plate
*5 Hook


f.
U110690

Loosely install the 3 bolts several threads.


g.
A290223E05
2.563,1.927 2.406,1.927 2.406,1.927 2.229,1.521 false 1.063,1.875 1.219,1.875 1.219,1.875 1.219,1.458 false 2.594,1.844 2.76,2.01 0.167,0.167 10 false *2 0.885,1.792 1.052,1.958 0.167,0.167 10 false *1

Apply clean engine coolant to the O-ring.

Text in Illustration
*1 Exhaust By-pass Pipe
*2 O-ring

NOTICE:

Do not damage the O-ring or allow it to become contaminated with foreign matter during work.



h.
A289461E02
0.448,0.24 0.615,0.24 0.615,0.24 0.698,0.385 false 0.333,1.115 0.677,1.115 false 1.427,0.74 1.198,0.74 false 0.25,0.156 0.417,0.323 0.167,0.167 10 false *1 0.167,1.031 0.333,1.198 0.167,0.167 10 false *3 1.458,0.667 1.625,0.833 0.167,0.167 10 false *2

Install the exhaust by-pass pipe to the exhaust pipe gas control actuator sub-assembly.

Text in Illustration
*1 Front Exhaust Pipe Assembly
*2 No. 2 Exhaust Pipe Heat Insulator
*3 Exhaust By-pass Pipe

NOTICE:
·

Make sure to insert the front exhaust pipe assembly into the exhaust pipe gas control actuator as far as possible.

·

Confirm that the front exhaust pipe assembly, exhaust by-pass pipe and No.2 exhaust pipe heat insulator are positioned correctly.

·

When reusing the exhaust by-pass pipe, inspect the O-ring.

·

If the O-ring has scratches or cuts, replace the exhaust by-pass pipe.

·

Make sure that the O-ring and the fitting section of the exhaust pipe gas control actuator sub-assembly are free of oil or foreign matter.

·

Do not touch the O-ring or fitting section of the exhaust pipe gas control actuator sub-assembly.




i.
U110696E02
0.781,0.76 0.927,0.948 0.146,0.188 10 false 1 2.01,0.385 2.135,0.531 0.125,0.146 10 false 2

Install the 2 bolts in the order shown in the illustration.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


j.
A292937E04
1.708,1.927 1.573,1.927 1.573,1.927 1.313,1.146 false 1.333,0.344 1.51,0.5 0.177,0.156 10 true *a 1.74,1.833 1.906,2 0.167,0.167 10 false *1

Confirm that the valve plate is positioned correctly by pressing the plate.

Text in Illustration
*1 Valve Plate
*a Insertion Direction

HINT:

If the valve plate is not positioned correctly, the final exhaust pipe gas control actuator sub-assembly position may be difficult to achieve.



k.
U110689E03
1.583,0.375 1.708,0.521 0.125,0.146 10 false 1 1.01,1.625 1.135,1.771 0.125,0.146 10 false 2 2.771,1.302 2.896,1.448 0.125,0.146 10 false 3

Tighten the 3 bolts in the order shown in the illustration in several steps.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


l.

Adjust the installation position of the exhaust by-pass pipe.

i.
A289466E04
0.635,3.094 0.729,3.094 0.729,3.094 0.896,2.833 true 1.552,2.969 1.552,2.354 1.552,2.354 1.073,2.354 false 1.073,2.885 1.552,2.885 false 1.333,2.146 1.229,2.146 1.229,2.146 1.229,2.229 false 2.125,2.813 2,2.979 2,2.979 1.938,2.979 false 2.281,2.365 2.74,2.365 2.74,2.365 2.74,2.958 false 2.281,2.896 2.74,2.896 false 2.406,2.229 2.406,2.146 2.406,2.146 2.573,2.146 false 0.396,2.063 0.573,2.219 0.177,0.156 10 false *a 1.833,2.042 2.01,2.198 0.177,0.156 10 false *b 1.354,2.063 1.531,2.219 0.177,0.156 10 false *1 0.469,3.01 0.646,3.167 0.177,0.156 10 false *3 1.458,2.979 1.635,3.135 0.177,0.156 10 false *2 2.604,2.083 2.75,2.24 0.146,0.156 10 false *1 1.75,2.885 1.927,3.042 0.177,0.156 10 false *3 2.656,2.969 2.833,3.125 0.177,0.156 10 false *2

Loosen the 2 bolts slightly.

NOTICE:

Do not remove these 2 bolts.



ii.

Move the exhaust by-pass pipe up and down to properly settle the O-ring.

Text in Illustration
*1 Exhaust Pipe Gas Control Actuator Sub-assembly
*2 O-ring
*3 Exhaust By-pass Pipe
*a OK (O-ring is not deformed.)
*b NG (O-ring is deformed.)

NOTICE:

Make sure to settle the O-ring to distribute the pressure applied to the upper part of the O-ring. Failure to do so may cause engine coolant to leak.




m.
U110696E02
0.781,0.76 0.927,0.948 0.146,0.188 10 false 1 2.01,0.385 2.135,0.531 0.125,0.146 10 false 2

Tighten the 2 bolts in the order shown in the illustration.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


n.

When replacing the exhaust pipe gas control actuator sub-assembly with a new one:

i.
A289468E01
2.493,2.943 2.655,3.105 0.162,0.162 10 *1 2.455,3.027 2.226,3.027 2.226,3.027 1.655,2.705 false

Remove the spacer from the new exhaust pipe gas control actuator sub-assembly.

Text in Illustration
*1 Spacer

NOTICE:

To prevent a malfunction of the exhaust pipe gas control actuator sub-assembly, the spacer must be removed.


HINT:

The spacer is provided with a new exhaust pipe gas control actuator sub-assembly.




Hide 17410 2.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 4.INSPECT FOR COOLANT LEAK (for Engine)

CAUTION:

Do not remove the radiator cap while the engine and radiator are still hot. Pressurized hot engine coolant and steam may be released and cause serious burns.


HINT:

Be sure to turn the A/C switch off before starting the following inspection.


a.

Turn the power switch off. Check for engine coolant leaks from the front exhaust pipe assembly and the heater hose around the exhaust pipe gas control actuator sub-assembly.


b.

Add engine coolant to the reserve tank and install a radiator cap tester.


c.

Pump the cap tester to 118 kPa (1.2 kgf/cm2, 17 psi), and then check that the pressure does not drop.

If the reading drops, check for leaks from the front exhaust pipe assembly and the heater hose around the exhaust pipe gas control actuator sub-assembly.


d.

Warm up the engine until the coolant temperature reaches the point that the exhaust pipe gas control actuator sub-assembly starts operating (80°C or more) and check for leaks

If external leaks are found, replace the exhaust pipe assembly.