Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › 2012.03–2014.11
RM2070E _51 Engine / Hybrid System _061914 CRUISE CONTROL _0301639 CRUISE CONTROL SYSTEM C

CRUISE CONTROL  CRUISE CONTROL SYSTEM  P0571  Brake Switch "A" Circuit  


DESCRIPTION

When the brake pedal is depressed, the stop light switch assembly sends a signal to the power management control ECU. When the power management control ECU receives this signal, it cancels cruise control system control of vehicle speed. The fail-safe function operates to enable normal driving even if there is a malfunction in the stop light signal circuit. The cancellation condition occurs when voltage is applied to terminal STP. When the brake is applied, voltage is normally applied to terminal STP of the power management control ECU through the STOP fuse and the stop light switch assembly, and the power management control ECU turns the cruise control off.

DTC No. DTC Detection Condition Trouble Area
P0571 Voltage of STP signal and that of ST1- terminal of power management control ECU are less than 1 V for 0.5 seconds or more
·

Stop light switch assembly

·

Stop light switch assembly circuit

·

Power management control ECU



WIRING DIAGRAM

E232844E03
3.542,1.302 5.302,1.49 1.76,0.188 10 false Stop Light Switch Assembly 3.542,1.156 3.823,1.302 0.281,0.146 10 false A26 0.667,3.948 1.229,4.323 0.563,0.375 10 false Auxiliary Battery 6.083,2.875 6.427,3.031 0.344,0.156 10 false IG2D 5.75,4.104 7.052,4.417 1.302,0.313 10 false Power Management Control ECU 5.75,3.938 6.094,4.094 0.344,0.156 10 false A22 4.167,3.094 4.438,3.25 0.271,0.156 10 false IG2 6.063,0.458 6.49,0.625 0.427,0.167 10 false STP 2.438,0.604 2.865,0.771 0.427,0.167 10 false STOP 0.531,2.896 0.979,3.052 0.448,0.156 10 false MAIN 3.198,2.615 3.552,2.781 0.354,0.167 10 false IG2 1.688,2.615 2.083,2.781 0.396,0.167 10 false P/I 1 5.875,2.75 6,2.917 0.125,0.167 10 false 2 3.844,0.354 3.969,0.521 0.125,0.167 10 false 2 3.844,0.792 3.969,0.958 0.125,0.167 10 false 4 4.521,0.354 4.646,0.521 0.125,0.167 10 false 1 4.521,0.781 4.646,0.948 0.125,0.167 10 false 3 2.5,1.052 3.073,1.219 0.573,0.167 10 false IGN 0.531,1.479 1.031,1.646 0.5,0.167 10 false DC/DC 5.802,0.344 6.021,0.51 0.219,0.167 10 false 23 5.875,0.771 5.979,0.938 0.104,0.167 10 false 7 6.063,0.885 6.49,1.052 0.427,0.167 10 false ST1-

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.INSPECT STOP LIGHT SWITCH ASSEMBLY (POWER SOURCE)
a.
U190506E02
0.313,0.156 0.5,0.333 0.188,0.177 10 false *a 0.75,2.281 1.021,2.427 0.271,0.146 10 false A26

Disconnect the stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A26-2 - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


c.

Reconnect the stop light switch assembly connector.



OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY (POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - AUXILIARY BATTERY)

2.INSPECT STOP LIGHT SWITCH ASSEMBLY (POWER SOURCE)
a.
U190507E02
0.313,0.156 0.5,0.333 0.188,0.177 10 false *a 0.75,2.281 1.021,2.427 0.271,0.146 10 false A26

Disconnect the stop light switch assembly connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A26-4 - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


d.

Reconnect the stop light switch assembly connector.



OK

3.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - IG2 RELAY)

3.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.
A167698E21
0.744,0.83 0.899,0.991 0.156,0.161 10 *b 2.086,0.83 2.287,0.996 0.200,0.166 10 *c 0.183,0.17 0.356,0.354 0.174,0.184 10 *a 2.377,2.052 2.484,2.200 0.107,0.148 10 1 1.004,2.052 1.121,2.209 0.116,0.157 10 2 1.004,2.733 1.103,2.877 0.098,0.143 10 4 2.377,2.733 2.484,2.881 0.107,0.148 10 3 1.127,2.131 1.637,2.3 false 1.133,2.806 1.624,2.532 false 1.897,2.532 2.36,2.8 false 1.886,2.301 2.344,2.147 false

Remove the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Switch pin not pushed Below 1 Ω
3 - 4 Switch pin not pushed 10 kΩ or higher
1 - 2 Switch pin pushed 10 kΩ or higher
3 - 4 Switch pin pushed Below 1 Ω


Text in Illustration
*a Component without harness connected
(Stop Light Switch Assembly)
*b Not pushed
*c Pushed


c.

Reinstall the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION).



OK

4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - POWER MANAGEMENT CONTROL ECU)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - POWER MANAGEMENT CONTROL ECU)
a.

Disconnect the power management control ECU connector.


b.

Disconnect the stop light switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A22-23 (STP) - A26-1 Always Below 1 Ω
A22-7 (ST1-) - A26-3 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A22-23 (STP) or A26-1 - Body ground Always 10 kΩ or higher
A22-7 (ST1-) or A26-3 - Body ground Always 10 kΩ or higher



d.

Reconnect the stop light switch assembly connector.


e.

Reconnect the power management control ECU connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER MANAGEMENT CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)