Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › 2014.11–2016.05
RM2070E _51 Engine / Hybrid System _061914 CRUISE CONTROL _0301639 CRUISE CONTROL SYSTEM C

CRUISE CONTROL  CRUISE CONTROL SYSTEM  P0571  Brake Switch "A" Circuit  


DESCRIPTION

When the brake pedal is depressed, the stop light switch assembly sends a signal to the power management control ECU. When the power management control ECU receives this signal, it cancels cruise control system control of vehicle speed. The fail-safe function operates to enable normal driving even if there is a malfunction in the stop light signal circuit. The cancellation condition occurs when voltage is applied to terminal STP. When the brake is applied, voltage is normally applied to terminal STP of the power management control ECU through the STOP fuse and the stop light switch assembly, and the power management control ECU turns the cruise control off.

DTC No. DTC Detection Condition Trouble Area
P0571 Voltage of STP signal and that of ST1- terminal of power management control ECU are less than 1 V for 0.5 seconds or more
·

Stop light switch assembly

·

Stop light switch assembly circuit

·

Power management control ECU



WIRING DIAGRAM

B389353E09
6.094,0.448 6.552,0.646 0.458,0.198 10 false STP 6.094,1.031 6.552,1.229 0.458,0.198 10 false ST1- 4.385,0.396 4.844,0.594 0.458,0.198 10 false 2 5.906,0.948 6.365,1.146 0.458,0.198 10 false 7 5.708,1.531 6.167,1.729 0.458,0.198 10 false A22 5.719,1.698 6.958,2.177 1.24,0.479 10 false Power Management Control System 5.854,0.396 6.313,0.594 0.458,0.198 10 false 23 4.385,0.948 4.844,1.146 0.458,0.198 10 false 4 4.01,0.469 4.469,0.667 0.458,0.198 10 false OUT 4.188,1.031 4.646,1.229 0.458,0.198 10 false L 3.604,0.375 4.063,0.573 0.458,0.198 10 false B 3.604,0.865 4.063,1.063 0.458,0.198 10 false B 3.604,1.188 4.063,1.385 0.458,0.198 10 false GND 3.24,1.604 3.698,1.802 0.458,0.198 10 false A80 3.229,1.75 4.375,2.188 1.146,0.438 10 false Stop Light Switch Assembly 2.49,1.01 2.948,1.208 0.458,0.198 10 false IGN 2.427,0.521 2.885,0.719 0.458,0.198 10 false STOP 0.646,0.365 1.521,0.844 0.875,0.479 10 false from Auxiliary Battery 0.573,0.875 1.823,1.156 1.25,0.281 10 false from IG2 Relay 3.427,0.292 3.885,0.49 0.458,0.198 10 false 1 3.427,0.781 3.885,0.979 0.458,0.198 10 false 5 3.427,1.125 3.885,1.323 0.458,0.198 10 false 3

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE, BODY GROUND)
a.
U190944E02
1.354,1.417 1.083,1.896 false 1.719,1.406 1.719,1.875 false 2.531,1.875 2.083,1.406 false 0.063,0.052 0.333,0.292 0.271,0.24 10 false *a 1.594,0.292 1.875,0.448 0.281,0.156 10 false A80 1.021,1.917 1.135,2.073 0.115,0.156 10 false B 1.563,1.906 1.917,2.052 0.354,0.146 10 false GND 2.521,1.896 2.76,2.052 0.24,0.156 10 false B

Disconnect the stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A80-3 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A80-1 (B) - A80-3 (GND) Always 11 to 14 V
A80-5 (B) - A80-3 (GND) Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


d.

Reconnect the stop light switch assembly connector.



OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

Inspect the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION).


OK

3.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL SYSTEM - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL SYSTEM - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the power management control system connector.


b.

Disconnect the stop light switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A22-23 (STP) - A80-2 (OUT) Always Below 1 Ω
A22-7 (ST1-) - A80-4 (L) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A22-23 (STP) or A80-2 (OUT) - Body ground Always 10 kΩ or higher
A22-7 (ST1-) or A80-4 (L) - Body ground Always 10 kΩ or higher


Result:
Result
NG
OK



d.

Reconnect the stop light switch assembly connector.


e.

Reconnect the ECM connector.



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B