Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2014.11–2017.12
RM2070E _51 Engine / Hybrid System _061914 CRUISE CONTROL _0301640 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  U0235  Lost Communication with Cruise Control Front Distance Range Sensor  U1104  Lost Communication with Driving Support ECU  


DESCRIPTION

The millimeter wave radar sensor assembly and driving support ECU assembly transmit the data for general vehicle control and diagnosis function via CAN communication line. The millimeter wave radar sensor assembly transmits information about the vehicle in front to the driving support ECU assembly.

DTC No. DTC Detection Condition Trouble Area
U0235 When the power switch is on (IG), a communication error between the millimeter wave radar sensor assembly and the driving support ECU assembly is detected for 1 second or more while the vehicle is being driven at a speed of 36 km/h (22 mph) or more.
·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly

·

CAN communication system


U1104 When the power switch is on (IG), a communication error between the driving support ECU assembly and the millimeter wave radar sensor assembly is detected for 1 second or more while the vehicle is being driven at a speed of 36 km/h (22 mph) or more.
·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly

·

CAN communication system



WIRING DIAGRAM

E248313E15
1.219,0.646 1.635,0.792 0.417,0.146 10 false CA1P 1.208,0.979 1.625,1.125 0.417,0.146 10 false CA1N 1.344,1.323 1.615,1.469 0.271,0.146 10 false IGB 1.177,1.646 1.594,1.792 0.417,0.146 10 false SGND 5.583,0.625 6,0.771 0.417,0.146 10 false CA1P 5.583,0.969 6,1.115 0.417,0.146 10 false CA1N 1.688,0.458 1.813,0.646 0.125,0.188 10 false 3 1.688,0.823 1.813,1.01 0.125,0.188 10 false 2 1.688,1.229 1.813,1.417 0.125,0.188 10 false 5 1.698,1.552 1.823,1.74 0.125,0.188 10 false 1 5.313,0.458 5.5,0.646 0.188,0.188 10 false 40 5.313,0.823 5.5,1.01 0.188,0.188 10 false 18 5.51,2.26 5.865,2.417 0.354,0.156 10 false L60 0.677,2.24 0.99,2.396 0.313,0.156 10 false A70 5.51,2.406 6.594,2.792 1.083,0.385 10 false Driving Support ECU Assembly 2.885,1.5 3.906,1.677 1.021,0.177 10 false ECU-IG NO. 2 0.667,2.406 2.073,2.802 1.406,0.396 10 false Millimeter Wave Radar Sensor Assembly 3.135,3.292 4.844,3.479 1.708,0.188 10 false : CAN Communication Line 3.521,2.052 4.896,2.24 1.375,0.188 10 false from IG1 NO. 1 Relay

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed (See page Engine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT).

·

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY)
a.

Disconnect the millimeter wave radar sensor assembly connector.


b.

Disconnect the driving support ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A76-3 (CA1P) - L60-40 (CA1P) Always Below 1 Ω
A76-2 (CA1N) - L60-18 (CA1N) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A76-3 (CA1P) or L60-40 (CA1P) - Body ground Always 10 kΩ or higher
A76-2 (CA1N) or L60-18 (CA1N) - Body ground Always 10 kΩ or higher



d.

Reconnect the millimeter wave radar sensor assembly connector.


e.

Reconnect the driving support ECU assembly connector.



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
a.
U191161E01
1.556,0.267 1.934,0.464 0.378,0.197 10 A76 2.642,0.546 3.030,0.685 0.388,0.139 10 IGB 0.052,0.044 0.365,0.183 0.314,0.139 10 *a 2,1.155 2.438,0.633 2.438,0.633 2.578,0.633 false

Disconnect the millimeter wave radar sensor assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A76-5 (IGB) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


c.

Turn the power switch OFF.


d.

Reconnect the millimeter wave radar sensor assembly connector.



OK

3.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BODY GROUND)
a.

Disconnect the millimeter wave radar sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A76-1 (SGND) - Body ground Always Below 1 Ω



c.

Reconnect the millimeter wave radar sensor assembly connector.



OK

4.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly (See page Engine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL).


b.

Adjust the millimeter wave radar sensor assembly (See page Engine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT).



NEXT

5.CHECK FOR DTCs (DTC U0235 OR U1104)
5.CHECK FOR DTCs (DTC U0235 OR U1104)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.



e.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the malfunction cannot be detected.


i.

Drive the vehicle at a speed of between approximately 50 km/h (30 mph) and 170 km/h (105 mph).


ii.

Turn the cruise control system on using the cruise control switch (ON-OFF button).


iii.

Push the cruise control switch to -/SET to begin control of vehicle speed using the cruise control system.



f.

Enter the following menus: Powertrain / Radar Cruise / Trouble Codes.


g.

Check for DTCs.

Result:
Result Proceed to
DTC is not output A
DTC U0235 or U1104 is output B




A

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)

B

REPLACE DRIVING SUPPORT ECU ASSEMBLY