Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2012.03–2014.11
RM2070E _51 Engine / Hybrid System _061914 CRUISE CONTROL _0301640 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  C1A05  Stop Light Switch Circuit  


DESCRIPTION

When the brake pedal is depressed, the stop light switch sends a signal to the driving support ECU assembly. Upon receiving the signal, the driving support ECU assembly cancels speed control by the dynamic radar cruise control system. Even if there is a malfunction in the stop light signal circuit while the cruise control is operating, normal driving is maintained due to the fail-safe function. Dynamic radar cruise control speed control operation is canceled when auxiliary battery voltage is applied to terminal STP-.

When the brake pedal is released, voltage is applied to terminal ST1- of the driving support ECU assembly through the IGN fuse and the stop light switch, and the driving support ECU assembly operates the dynamic radar cruise control.

The brake booster with master cylinder (skid control ECU) receives a signal from the driving support ECU assembly and operates the brake actuator. The brake booster with master cylinder (skid control ECU) operates the brake actuator and at the same time illuminates the stop lights by operating the stop light control relay.

The stop light switch assembly sends a brake pedal operation signal to the driving support ECU assembly.

After receiving the signal, the ECM performs fail-safe control by canceling cruise control system control of vehicle speed.

DTC No. DTC Detection Condition Trouble Area
C1A05 Voltages of terminals ST1- and STP- of driving support ECU assembly are both below 1 V for 1 second
·

Stop light switch assembly

·

Stop light switch circuit

·

Driving support ECU assembly



WIRING DIAGRAM

E230009E03
6.156,0.635 6.5,0.823 0.344,0.188 10 false ST1- 5.854,0.458 6.073,0.646 0.219,0.188 10 false 28 6.156,1.094 6.51,1.281 0.354,0.188 10 false STP- 4.49,3.021 4.844,3.208 0.354,0.188 10 false STP 4.917,2.896 5.052,3.083 0.135,0.188 10 false 5 4.49,3.417 4.844,3.604 0.354,0.188 10 false ACC 3.948,3.448 4.177,3.635 0.229,0.188 10 false +B 3.719,3.333 3.854,3.521 0.135,0.188 10 false 6 3.948,3.854 4.281,4.042 0.333,0.188 10 false GND 3.719,3.75 3.854,3.938 0.135,0.188 10 false 8 4.917,3.292 5.052,3.479 0.135,0.188 10 false 9 4.49,3.823 4.844,4.01 0.354,0.188 10 false OUT 4.917,3.698 5.052,3.885 0.135,0.188 10 false 1 5.854,0.906 6.073,1.094 0.219,0.188 10 false 27 6.156,3.01 6.5,3.198 0.344,0.188 10 false STP 5.854,2.896 6.073,3.083 0.219,0.188 10 false 33 6.156,3.427 6.552,3.615 0.396,0.188 10 false STPO 5.927,3.313 6.073,3.5 0.146,0.188 10 false 3 6.156,3.813 6.552,4 0.396,0.188 10 false STP2 5.927,3.698 6.073,3.885 0.146,0.188 10 false 6 5.781,1.521 6.031,1.719 0.25,0.198 10 false L60 6.083,1.531 7.063,1.896 0.979,0.365 10 false Driving Support ECU Assembly 4.771,0.448 4.906,0.635 0.135,0.188 10 false 3 4.083,0.448 4.219,0.635 0.135,0.188 10 false 4 4.771,0.906 4.906,1.094 0.135,0.188 10 false 1 4.083,0.906 4.219,1.094 0.135,0.188 10 false 2 3.813,1.375 4.427,1.625 0.615,0.25 10 false A26 4.125,1.375 5.24,1.781 1.115,0.406 10 false Stop Light Switch Assembly 3.104,4.208 3.396,4.406 0.292,0.198 10 false A28 3.385,4.208 5.583,4.427 2.198,0.219 10 false Stop Light Control Relay Assembly 2.417,5.219 2.708,5.417 0.292,0.198 10 false R17 3.625,4.917 3.781,5.115 0.156,0.198 10 false B 3.104,4.917 3.396,5.115 0.292,0.198 10 false E 3.854,4.646 4.031,4.844 0.177,0.198 10 false 4 2.854,4.646 3.031,4.844 0.177,0.198 10 false 5 2.719,5.219 4.458,5.438 1.74,0.219 10 false Rear Combination Light LH 2.406,6.26 2.698,6.458 0.292,0.198 10 false S18 3.854,5.677 4.031,5.875 0.177,0.198 10 false 4 2.854,5.677 3.031,5.875 0.177,0.198 10 false 5 2.719,6.26 4.458,6.479 1.74,0.219 10 false Rear Combination Light RH 2.427,7.292 2.719,7.49 0.292,0.198 10 false d1 3.854,6.719 4.031,6.917 0.177,0.198 10 false 2 4.021,7.99 4.146,8.188 0.125,0.198 10 false B 4.229,7.854 4.406,8.052 0.177,0.198 10 false 1 2.854,6.719 3.031,6.917 0.177,0.198 10 false 1 2.656,7.292 4.448,7.51 1.792,0.219 10 false Center Stop Light Assembly 3.385,8.323 3.677,8.521 0.292,0.198 10 false R32 3.708,8.323 4.406,8.542 0.698,0.219 10 false CLC Filter 5.594,4.25 5.885,4.448 0.292,0.198 10 false A58 5.917,4.25 7.115,4.875 1.198,0.625 10 false Brake Booster with Master Cylinder (Skid Control ECU) 1.573,1.333 1.875,1.521 0.302,0.188 10 false IG2 3,0.792 3.302,0.979 0.302,0.188 10 false IGN 2.073,2.313 2.375,2.5 0.302,0.188 10 false STP 2.469,2.177 2.688,2.365 0.219,0.188 10 false 23 1.333,2.031 1.552,2.219 0.219,0.188 10 false 2 1.552,2.146 1.906,2.333 0.354,0.188 10 false IG2D 0.844,3.677 1.323,3.865 0.479,0.188 10 false DC/DC 0.458,7.052 0.938,7.24 0.479,0.188 10 false MAIN 0.542,7.865 1.177,8.198 0.635,0.333 10 false Auxiliary Battery 2.063,3.667 2.542,3.854 0.479,0.188 10 false STOP 0.521,2.833 0.813,3.031 0.292,0.198 10 false A22 0.823,2.833 3,3.031 2.177,0.198 10 false Power Management Control ECU 0.438,1.229 0.74,1.417 0.302,0.188 10 false IG2 0.438,2.292 0.823,2.479 0.385,0.188 10 false P/I 1 3.615,5.958 3.771,6.156 0.156,0.198 10 false B 3.104,5.958 3.396,6.156 0.292,0.198 10 false E 3.615,6.99 3.771,7.188 0.156,0.198 10 false B 3.104,6.99 3.396,7.188 0.292,0.198 10 false E

CAUTION / NOTICE / HINT

HINT:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - POWER SOURCE)
a.
U190508E02
0.188,0.104 0.438,0.292 0.25,0.188 10 false *a 0.719,2.208 0.99,2.385 0.271,0.177 10 false A26

Disconnect the stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A26-2 - Body ground Always 11 to 14 V
A26-4 - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


c.

Reconnect the stop light switch assembly connector.



OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH - IG2 RELAY OR BATTERY)

2.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.
A167698E21
0.744,0.83 0.899,0.991 0.156,0.161 10 *b 2.086,0.83 2.287,0.996 0.200,0.166 10 *c 0.183,0.17 0.356,0.354 0.174,0.184 10 *a 2.377,2.052 2.484,2.200 0.107,0.148 10 1 1.004,2.052 1.121,2.209 0.116,0.157 10 2 1.004,2.733 1.103,2.877 0.098,0.143 10 4 2.377,2.733 2.484,2.881 0.107,0.148 10 3 1.127,2.131 1.637,2.3 false 1.133,2.806 1.624,2.532 false 1.897,2.532 2.36,2.8 false 1.886,2.301 2.344,2.147 false

Remove the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Switch pin not pushed Below 1 Ω
3 - 4 Switch pin not pushed 10 kΩ or higher
1 - 2 Switch pin pushed 10 kΩ or higher
3 - 4 Switch pin pushed Below 1 Ω


Text in Illustration
*a Component without harness connected
(Stop Light Switch Assembly)
*b Not pushed
*c Pushed



OK

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY)
a.

Disconnect the stop light switch assembly connector.


b.

Disconnect the driving support ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A26-3 - L60-28 (ST1-) Always Below 1 Ω
A26-1 - L60-27 (STP-) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A26-3 or L60-28 (ST1-) - Body ground Always 10 kΩ or higher
A26-1 or L60-27 (STP-) - Body ground Always 10 kΩ or higher



d.

Reconnect the stop light switch assembly connector.


e.

Reconnect the driving support ECU assembly connector.



OK

4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)
a.

Disconnect the stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A26-1 - Body ground Always 10 kΩ or higher
A26-3 - Body ground Always 10 kΩ or higher



c.

Reconnect the stop light switch assembly connector.



OK

REPLACE DRIVING SUPPORT ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)