When the driving support ECU assembly receives a hybrid control system or SFI system malfunction signal from the hybrid vehicle control ECU or ECM via CAN communication, DTC C1A40 is stored.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| C1A40 | While power switch is on (IG), hybrid control system or SFI system malfunction signal is detected for 1 second or more while the dynamic radar cruise control is operating | ·
Hybrid control system ·
Hybrid vehicle control ECU ·
SFI system ·
ECM ·
Driving support ECU assembly |
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC is output | B |
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC is output | B |
A
B
(See pageEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Clear the DTCs (See page Engine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR).
Perform the following to make sure that the DTC detection conditions are met.
If the detection conditions are not met, the malfunction cannot be detected.
Drive the vehicle at a speed of between approximately 50 km/h (30 mph) and 170 km/h (105 mph).
Turn the cruise control system on using the cruise control switch (ON-OFF button).
Push the cruise control switch to -/SET to begin control of vehicle speed using the cruise control system.
Enter the following menus: Powertrain / Radar Cruise / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC C1A40 is output | B |
A
B
Replace the hybrid vehicle control ECU (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID VEHICLE CONTROL ECU>REMOVAL).
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Clear the DTCs (See page Engine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR).
Perform the following to make sure that the DTC detection conditions are met.
If the detection conditions are not met, the malfunction cannot be detected.
Drive the vehicle at a speed of between approximately 50 km/h (30 mph) and 170 km/h (105 mph).
Turn the cruise control system on using the cruise control switch (ON-OFF button).
Push the cruise control switch to -/SET to begin control of vehicle speed using the cruise control system.
Enter the following menus: Powertrain / Radar Cruise / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC C1A40 is output | B |
A
B
Replace the ECM (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>ECM>REMOVAL).
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Clear the DTCs (See page Engine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR).
Perform the following to make sure that the DTC detection conditions are met.
If the detection conditions are not met, the malfunction cannot be detected.
Drive the vehicle at a speed of between approximately 50 km/h (30 mph) and 170 km/h (105 mph).
Turn the cruise control system on using the cruise control switch (ON-OFF button).
Push the cruise control switch to -/SET to begin control of vehicle speed using the cruise control system.
Enter the following menus: Powertrain / Radar Cruise / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC C1A40 is output | B |
A
B