Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2012.03–2014.11
RM2070E _51 Engine / Hybrid System _061914 CRUISE CONTROL _0301640 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  C1A4B  Stop Light Relay Circuit  


DESCRIPTION

The brake booster with master cylinder (skid control ECU) sends a stop light operation signal to the stop light control relay assembly. When the brake booster with master cylinder (skid control ECU) detects a malfunction in the stop light circuit, the driving support ECU assembly stores DTC C1A4B.

DTC No. DTC Detection Condition Trouble Area
C1A4B Either of the following conditions is met:
·

When the vehicle speed is approximately 50 km/h or more, the cruise control switch (ON-OFF button) is on, the IG1 terminal voltage is between 11 and 14 V and the stop light illumination output signal (STPO) is output, the signal is not received at terminal STP2 for 0.3 seconds or more.

·

When the vehicle speed is approximately 50 km/h or more, the cruise control switch (ON-OFF button) is on, the IG1 terminal voltage is between 11 and 14 V and the stop light illumination output signal (STPO) is not output, the signals received at terminals STP and STP2 are different for 0.3 seconds or more.


·

Lighting system

·

Electronically controlled brake system

·

Harness or connector

·

Stop light control relay assembly

·

Driving support ECU assembly



WIRING DIAGRAM

A318941E13
1.25,3.271 2.771,3.813 1.521,0.542 10 false Stop Light Control Relay Assembly 4.917,5.948 7.094,6.563 2.177,0.615 10 false Brake Booster with Master Cylinder (Skid Control ECU) 0.396,5.823 2.844,6.104 2.448,0.281 10 false Driving Support ECU Assembly 0.906,0.365 2.583,0.635 1.677,0.271 10 false from Auxiliary Battery 4.771,0.344 7.063,0.542 2.292,0.198 10 false from Stop Light Switch Assembly 0.531,1.365 1.146,1.563 0.615,0.198 10 false STOP 1.24,6.26 3.26,6.521 2.021,0.26 10 false : CAN Communication Line 2.865,3.594 3.938,3.792 1.073,0.198 10 false for Stop Light 1.583,1.198 1.896,1.396 0.313,0.198 10 false +B 1.573,2.26 2.031,2.458 0.458,0.198 10 false GND 2.365,1.198 2.823,1.396 0.458,0.198 10 false STP 5.625,1.229 6.083,1.427 0.458,0.198 10 false STP 2.344,1.896 2.802,2.094 0.458,0.198 10 false ACC 5.625,1.917 6.24,2.115 0.615,0.198 10 false STPO 5.646,2.604 6.26,2.802 0.615,0.198 10 false STP2 2.344,2.583 2.802,2.781 0.458,0.198 10 false OUT 1.385,1.104 1.542,1.302 0.156,0.198 10 false 6 1.375,2.146 1.531,2.344 0.156,0.198 10 false 8 2.74,1.115 2.896,1.313 0.156,0.198 10 false 5 2.74,1.813 2.896,2.01 0.156,0.198 10 false 9 2.74,2.49 2.896,2.688 0.156,0.198 10 false 1 5.365,1.115 5.625,1.323 0.26,0.208 10 false 33 5.427,2.479 5.583,2.677 0.156,0.198 10 false 6 5.417,1.802 5.573,2 0.156,0.198 10 false 3 1.25,3.115 2,3.49 0.75,0.375 10 false A28 4.906,5.792 5.729,6.177 0.823,0.385 10 false A58

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When this DTC is output, malfunction in the lighting system is suspected. Check if the lighting system is functioning normally (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed On
Brake pedal released Off




OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT CONTROL RELAY ASSEMBLY)

NG

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT CONTROL RELAY ASSEMBLY)
a.

Turn the power switch off.


b.

Disconnect the A28 Stop light control relay assembly connector.


c.
U190767E02
1.208,1.458 1.052,1.76 false 0.167,0.115 0.344,0.292 0.177,0.177 10 false *a 1.427,0.26 2.042,0.438 0.615,0.177 10 false A28 0.938,1.771 1.177,1.948 0.24,0.177 10 false +B

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A28-6 (+B) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Control Relay Assembly)



OK

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT CONTROL RELAY ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT CONTROL RELAY ASSEMBLY - BODY GROUND)
a.

Turn the power switch off.


b.

Disconnect the A28 stop light control relay assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A28-8 (GND) - Body ground Always Below 1 Ω




OK

4.CHECK TERMINAL VOLTAGE (STP TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK TERMINAL VOLTAGE (STP TERMINAL)
a.

Turn the power switch off.


b.

Disconnect the A58 brake booster with master cylinder (skid control ECU) connector.


c.
U190770E02
1.531,1.344 1.156,1.854 false 0.135,0.083 0.344,0.271 0.208,0.188 10 false *a 1.583,0.156 1.896,0.323 0.313,0.167 10 false A58 1,1.875 1.323,2.042 0.323,0.167 10 false STP

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A58-33 (STP) - Body ground Brake pedal depressed 11 to 14 V
A58-33 (STP) - Body ground Brake pedal released Below 1.5 V


Text in Illustration
*a Front view of wire harness connector
(to Brake Booster with Master Cylinder (Skid Control ECU))



OK

5.CHECK TERMINAL VOLTAGE (STP TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK TERMINAL VOLTAGE (STP TERMINAL)
a.

Turn the power switch off.


b.

Disconnect the A28 stop light control relay assembly connector.


c.
U190768E02
1.031,1.448 0.875,1.75 false 0.125,0.063 0.302,0.24 0.177,0.177 10 false *a 1.427,0.26 2.042,0.438 0.615,0.177 10 false A28 0.708,1.76 1.063,1.938 0.354,0.177 10 false STP

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A28-5 (STP) - Body ground Brake pedal depressed 11 to 14 V
A28-5 (STP) - Body ground Brake pedal released Below 1.5 V


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Control Relay Assembly)



OK

6.PERFORM ACTIVE TEST USING GTS (STOP LIGHT RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.PERFORM ACTIVE TEST USING GTS (STOP LIGHT RELAY)
a.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.


b.

Perform "Active Test" according to the display on GTS.

Tester Display Measurement Item Control Range Diagnostic Note
Stop Light Relay Stop light control relay assembly (STOP LP) ON or OFF Stop lights come on


c.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light Relay Output Stop light control relay assembly (STOP LP) output/
ON or OFF
ON: Relay output on (Stop light on)
OFF: Relay output off (Stop light off)
-

Result:
Result Result
Data List item changes between ON and OFF, but stop lights do not turn on A
Data List item changes between ON and OFF and stop lights turn on and off B




A

7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - STOP LIGHT CONTROL RELAY ASSEMBLY)

B

8.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - STOP LIGHT CONTROL RELAY ASSEMBLY)
7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - STOP LIGHT CONTROL RELAY ASSEMBLY)
a.

Turn the power switch off.


b.

Disconnect the A58 brake booster with master cylinder (skid control ECU) connector.


c.

Disconnect the A28 stop light control relay assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A58-3 (STPO) - A28-9 (ACC) Always Below 1 Ω
A58-3 (STPO) - A28-9 (ACC) Always 10 kΩ or higher




OK

8.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - STOP LIGHT CONTROL RELAY ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - STOP LIGHT CONTROL RELAY ASSEMBLY)
a.

Turn the power switch off.


b.

Disconnect the A58 brake booster with master cylinder (skid control ECU) connector.


c.

Disconnect the A28 stop light control relay assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A58-6 (STP2) - A28-1 (OUT) Always Below 1 Ω




OK

9.CHECK TERMINAL VOLTAGE (STP2 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK TERMINAL VOLTAGE (STP2 TERMINAL)
a.

Turn the power switch off.


b.

Disconnect the A58 brake booster with master cylinder (skid control ECU) connector.


c.
U190769E02
1.646,0.885 1.99,0.177 1.99,0.177 2.146,0.177 false 0.135,0.104 0.344,0.292 0.208,0.188 10 false *a 1.135,0.156 1.448,0.323 0.313,0.167 10 false A58 2.188,0.104 2.813,0.271 0.625,0.167 10 false STP2

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A58-6 (STP2) - Body ground Brake pedal depressed 11 to 14 V
A58-6 (STP2) - Body ground Brake pedal released Below 1.5 V


Text in Illustration
*a Front view of wire harness connector
(to Brake Booster with Master Cylinder (Skid Control ECU))



OK

10.CHECK FOR DTCs (RADAR CRUISE)

NG

REPLACE STOP LIGHT CONTROL RELAY ASSEMBLY

10.CHECK FOR DTCs (RADAR CRUISE)
a.

Turn the power switch off and wait for at least 2 minutes.



c.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.

·

Drive the vehicle at a speed of approximately 50 km/h or more with the cruise control switch (ON-OFF button) on.




d.

Check for DTCs (See page Engine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR).

Result:
Result Result
DTC C1A4B is not output A
DTC C1A4B is output B


NOTICE:

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.




A

END

B

REPLACE DRIVING SUPPORT ECU ASSEMBLY